Contact Us

INA131AP

Brand: Texas Instruments
Texas Instruments INA131AP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA131AP — Power Management & Signal Chain | Superb Automation

INA131AP

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA131AP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA131AP: a fixed gain of 100 in an eight pin DIP, in the wider of the two offset bins

The INA131AP is the A grade of a fixed gain 100 instrumentation amplifier in an eight pin plastic DIP. It is the member of the family with the wider offset window: 125 µV maximum against 50 on the BP grade, and 1 µV per degree of drift against 0.25. The gain itself is trimmed inside the package and cannot be changed, which removes the external resistor and its tolerance from the error budget entirely.

The rest of the sheet is a rack instrument part: 3 mA of supply current, a plus or minus 2.25 V to plus or minus 18 V window, 70 kHz of bandwidth at the fixed gain, 0.7 V per microsecond of slew and 100 microseconds of settling to 0.01 per cent. On a bridge, an RTD or a thermocouple channel sampled a few times a second it is comfortable; on a multiplexed front end the settling figure sets the scan rate.

The INA131AP rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, fixed gain of 100
Vendor statusActive, production
Data sheetSBOS016, Burr-Brown PDS-1144E, March 1998
GradeAP, 125 µV maximum offset and 1 µV per degree drift
Gain100 V/V, trimmed on the die, no external resistor
Gain error0.1 per cent maximum on the AP grade
Gain drift20 ppm per degree maximum on the AP grade
Input offset voltage125 µV maximum initial, 1 µV per degree over temperature
Input bias current2 nA maximum, 8 pA per degree of drift
Voltage noise12 nV per root hertz at 1 kHz, 0.4 µV peak to peak from 0.1 to 10 Hz
Common mode rejection106 dB minimum with a 1 kΩ source imbalance
Bandwidth70 kHz at a gain of 100
Slew rate0.7 V per microsecond
Settling100 µs to 0.01 per cent, 20 µs overload recovery from a 50 per cent overdrive
OutputPlus or minus 13.7 V at 5 mA on a plus or minus 15 V supply
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current2.2 mA typical, 3 mA maximum
Body8 pin plastic DIP, drawing 006
Temperature rangeMinus 40 to plus 85 degrees

A gain of 100 fixed inside the package

The INA131 has no gain resistor pin. The three op amp network and the resistors that set the gain are trimmed on the die to a fixed 100 V/V, and the eight pin body carries only the two inputs, the two supplies, the reference and the output. That removes the external resistor, its tolerance, its temperature coefficient and the resistance of the path to it, which at a gain of 100 is worth more than a tenth of a per cent on its own. It also means the gain cannot be moved: a channel that needs 50 or 200 is a different part.

The trimmed ratio is quoted as a gain error of 0.024 per cent maximum on INA131AP in the BP grade and 0.1 per cent in the AP grade, with a gain drift of 10 and 20 ppm per degree. Nonlinearity is 0.002 per cent of full scale on the BP row. On a 10 mV bridge those numbers are far below the offset and the noise, so the fixed gain is not what limits a bridge channel; on a channel that is calibrated against a reference the 0.024 per cent is the number that decides whether the calibration holds across temperature.

3 mA of supply current and the plus or minus 2.25 V to 18 V window

At 2.2 mA typical and 3 mA maximum, INA131AP draws four times what the INA128 family draws, and that is the price of the wider bandwidth and the fixed gain network. It is a loop powered transmitter part only at the top of the current budget; on a 4 to 20 mA loop with 3.5 mA allocated to the electronics it fits with little left over for a reference. On a rack instrument with a plus or minus 15 V supply it is irrelevant.

The supply window runs from plus or minus 2.25 V to plus or minus 18 V, so the part runs from a single 5 V rail as long as the reference sits mid rail, and from a plus or minus 15 V rail without a regulator. The absolute maximum is 18 V per rail, which means a 15 V rail with a 10 per cent transient is already at the limit, and a supply that can ring above 18 V needs a clamp rather than a hope. Power supply rejection is 3 microvolts per volt maximum on the BP grade.

50 microvolts on the BP and 125 on the AP

The two grades in this family are INA131AP AP and BP, and the difference is the offset window. The BP row is 50 microvolts maximum initial offset with 0.25 microvolts per degree of drift; the AP row is 125 microvolts maximum with 1 microvolt per degree. Both are laser trimmed at wafer level, both share the 2 nA bias current and the 12 nanovolts per root hertz of voltage noise, and both are specified over minus 40 to plus 85 degrees.

At a gain of 100 an input offset of 50 microvolts is 5 millivolts at the output, which against a 2 V output span is a quarter of a per cent and can be trimmed once in production. The drift is the part that cannot be trimmed: 0.25 microvolts per degree over a 45 degree swing is 11 microvolts at the input, a fifth of the initial offset, while the AP row moves 45 microvolts over the same swing. On a channel calibrated at 25 degrees and used at 70, the grade decides the error.

70 kHz at a gain of 100 and 0.7 V per microsecond

Fixed gain means a fixed bandwidth: INA131AP is quoted at 70 kHz for a 3 dB point at a gain of 100, with a slew rate of 0.7 volts per microsecond and a settling time of 100 microseconds to 0.01 per cent. The slew rate, not the small signal bandwidth, sets the large signal behaviour, and 0.7 volts per microsecond means a 10 V step takes 14 microseconds before settling even starts.

For a multiplexed front end the 100 microsecond settling figure is the scan budget: sixteen channels at that rate is 1.6 milliseconds per scan, or about 600 scans per second, with nothing left for the converter. That is still fast enough for a temperature or pressure logger and too slow for a vibration channel. Overload recovery from a 50 per cent overdrive is 20 microseconds, which matters when a multiplexer switches from an open channel to a live one.

40 V of input protection and a 2 nA bias current

The inputs on INA131AP survive 40 volts beyond either rail without damage, and the protection is internal, so a transducer plugged in while the rack is live does not take the amplifier with it. The safe input voltage row is quoted as plus or minus 40 V with the source at zero ohms, which is the worst case for the internal clamp current and the number to size the external resistor against.

Bias current is 2 nA maximum at 25 degrees, rising with temperature at about 8 picoamps per degree, and it flows in the source impedance. A 10 kohm bridge impedance and 2 nA is 20 microvolts of offset, which is a fifth of the input offset and worth knowing before blaming the part. A 1 kohm source keeps that error at 2 microvolts. The bias current return path has to exist: on a floating source such as a thermocouple, a DC path to the reference is required or the input sits at whatever leakage allows.

The eight pin DIP only, 100 degrees per watt to the board

INA131AP is available in one body, the eight pin plastic DIP with drawing 006, and there is no surface mount row in the current addendum. That decides the assembly route: through hole, wave or selective solder, and a board that is otherwise all SMD needs a mixed process for one part. The junction to ambient figure is 100 degrees per watt, so 3 mA at 15 V per rail, about 90 milliwatts, raises the junction 9 degrees above ambient, which is comfortable.

The output swings to within 1.3 V of each rail at 5 mA, so on a plus or minus 15 V supply the usable span is plus or minus 13.7 V, and a 1000 pF load is stable. Short circuit current is plus 20 and minus 15 mA, which is enough to hold a cable but not to drive a speaker. Common mode rejection is 110 dB minimum on the BP grade and 106 on the AP grade, measured with a 1 kohm source imbalance at plus or minus 10 V.

Buying INA131AP

This is a through hole part with no surface mount row in the current addendum, so the assembly route has to be decided before the part is bought: a mixed process for one DIP on an otherwise surface mount board, or a socket on a small board. The DIP is also the reason the part survives in rack instruments that were built in the 1990s and are still in service, which is where most of the demand comes from.

The grade is the only real choice. The BP row halves the offset and quarters the drift for a price step, and on a channel that is calibrated once at 25 degrees the AP drift of 1 µV per degree is 45 µV over the industrial range against 11 on the BP, which at a gain of 100 is 4.5 mV against 1.1 mV at the output. Our obsolete part cross reference page is where a long lived DIP part usually starts when the line needs a second source.

Questions that arrive with this part number

Whether the gain can be changed is the first question, and it cannot: the network is trimmed at 100 and the package has no gain pins, so a channel that needs 50 or 200 is a different part. The second is whether the AP grade can stand in for the BP, and the answer is only where the offset budget has room, because the drift is four times larger and drift is the term that cannot be trimmed at test.

The third is the body. There is no surface mount row, so a reel fed line needs a hand place or a selective solder step for this part, and a board file that assumed a SOIC will not find one in the addendum. That is worth confirming before a board is released rather than after the stencil is cut.