INA128UA
Product Specifications
INA128UA
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA128UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA128UA: the A grade SOIC in a 75 piece tube
The INA128UA is the A grade of the eight pin SOIC body in a 75 piece tube, which makes it the calibrated build carrier of this family. The A suffix is the tighter offset and gain error bin on the same die, and it is chosen when the channel full scale is small enough that the plain grade offset would need a trim and the tighter bin removes it. The tube matches a build of a few hundred boards and a bench that does not want to open a reel.
The family rows are unchanged: 0.5 µV per degree of drift on both grades, 5 nA of bias current, 8 nV per root hertz of noise, 120 dB of common mode rejection, 700 µA of quiescent current and a supply range from plus or minus 2.25 V to plus or minus 18 V. The gain equation is G = 1 + 50 kΩ divided by RG, and the current feedback stage holds 200 kHz at a gain of 100.
The INA128UA rows as the addendum publishes them
| Part class | Precision instrumentation amplifier, three op amp, current feedback |
| Vendor status | Active, production |
| Data sheet | SBOS051G, revised January 2026 |
| Grade | A suffix, tighter offset and gain error window |
| Gain equation | G = 1 + 50 kΩ divided by RG |
| Gain range | 1 to 10,000 V/V |
| Input offset voltage | Family row 50 µV maximum, tighter on the A bin |
| Offset drift | 0.5 µV per degree maximum, both grades |
| Input bias current | 5 nA maximum |
| Voltage noise | 8 nV per root hertz at 1 kHz |
| Common mode rejection | 120 dB minimum |
| Bandwidth | 1.3 MHz at a gain of 1, 200 kHz at a gain of 100 |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Quiescent current | 700 µA typical |
| Body | SOIC, D outline, 8 pins, 4.9 by 6 mm |
| Carrier | 75 pieces per tube |
| Lead finish | Nickel palladium gold on the published rows |
| Moisture level | Level 2, 260 degrees, one year floor life |
50 µV of offset and half a microvolt per degree
The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA128UA can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.
The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.
Gain error rows, the A grade and the 0.024 per cent window
Gain error on this family is quoted per gain setting and per grade, and the tightest row is 0.024 per cent at a gain of 1 on the A grade parts. That figure is smaller than the tolerance of the resistor that sets the gain, so the resistor, not the amplifier, is what a calibration adjusts. At a gain of 100 the family rows widen and the A grade still holds a window about half as wide as the plain grade, which is the practical difference between the two bins on a channel that is calibrated once rather than per unit.
Nonlinearity is 0.001 per cent of full scale on the plain grade and 0.0005 per cent on the A grade, which is well below any converter this part is likely to drive. The number that limits a real channel is the gain drift, quoted in ppm per degree, because it cannot be trimmed at the bench and it moves with the cabinet temperature. On INA128UA the drift row is the one to put in a specification that has to hold over temperature, and the room temperature gain error row is the one to put in a production test limit.
Current feedback input stage and bandwidth at a gain of 100
The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA128UA serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.
Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.
The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm
The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.
The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA128UA the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.
The REF pin, the 8 Ω rule and single supply references
The REF pin sets the output level and is part of the signal path in a way that is easy to forget. Any resistance in series with it appears as a common mode error at the input and as a gain error at the output at the same time, and the vendor states that 8 Ω is enough to degrade common mode rejection on a typical part. A divider made of two 10 kΩ resistors has a source impedance of 5 kΩ, which is three orders of magnitude above that, so an unbuffered divider is not a reference for INA128UA at any gain.
On a bipolar supply the REF pin goes to ground, and ground has to be the same ground the converter uses or the difference appears as an offset. On a single supply the pin goes to a buffered mid rail, and the buffer has to be able to sink and source the current the REF pin draws, which is small but not zero. A shunt reference with a 1 µF capacitor is the cheap answer; an op amp buffer is the answer when the reference also has to drive other channels. Both are one more part than a divider and both are the reason a single supply channel measures what it claims.
120 dB of common mode rejection and the source imbalance that removes it
The common mode rejection row is 120 dB minimum on the family, measured with a 1 kΩ source imbalance, and it is the number that decides whether a bridge channel can reject a 50 Hz disturbance. Rejection degrades with source imbalance at roughly 1 dB per 100 Ω above the test condition, so a channel with a 10 kΩ mismatch between the two input legs has thrown away most of the 120 dB. In practice that mismatch comes from the sensor rather than from the board: a 350 Ω bridge with one leg 5 Ω high, or a thermocouple with a 2 kΩ cable resistance on one side only.
The fix is a pair of matched resistors at the input, or a buffer for each leg, or a sensor with a trimmed output impedance. The REF pin is part of the same problem: the vendor notes that 8 Ω in series with REF is enough to degrade rejection on a typical part, so the reference has to be driven from a low impedance source such as an amplifier or a shunt reference with a capacitor, not from a divider alone. On INA128UA the rejection also falls with frequency, and the vendor curve of rejection against frequency is the one to read for a switching supply disturbance rather than the dc row.
Buying INA128UA in the tube
The A grade is a specification decision, not a purchasing preference. On a 1 mV full scale the plain grade offset is five per cent of range and the A bin is roughly half of that, so the grade is the difference between a trim and no trim. On a 100 mV full scale neither matters and the plain grade is the better buy at the same price band.
The tube suits a build that finishes in a few months. Beyond that the reel rows of the same die carry a lower per piece cost and a level 3 floor life that has to be managed. Our component lead time page covers how the tube and reel schedules are set, and the amplifier cross reference page lists what we compare when this grade is short.
Questions that arrive with this part number
Whether the grade is visible on the part is the first question and the answer is no, so the label and the order line are the only record. The second is whether the A grade helps over temperature, and it does not: the drift row is the same on both bins, so the grade buys room temperature accuracy and the cabinet performance is set by the family drift.
The third is the reference again. It is the pin most often left as a divider, and at 8 Ω the vendor is naming a threshold three orders of magnitude below a 10 kΩ divider. Driving REF from a buffer or a shunt reference with a capacitor is the difference between 120 dB of rejection and whatever the divider happens to give.