Contact Us

TPS7B8133DGNR

Brand: Texas Instruments
Texas Instruments TPS7B8133DGNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7B8133DGNR — Power Management & Signal Chain | Superb Automation

TPS7B8133DGNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7B8133DGNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7B8133DGNR: a 150 mA, 40 V regulator with a fixed 3.3 V output and 2.7 uA of quiescent current

TPS7B8133DGNR is a 150 mA low dropout regulator with a fixed 3.3 V output that runs from 3 V to 40 V and draws microamps at light load, built for battery packs, detectors and power tools in a HVSSOP body of 8 pins. The 45 V transient tolerance is what removes the external clamp on an inductive load, and the 2.7 uA typical quiescent current is what lets the node stay connected for years.

Order code and package

Catalogue stringTPS7B8133DGNR, that is the 3.3 V fixed member in the DGN body with the R reel letter
BodyDGN, HVSSOP, 8 pins with thermal pad, 3.00 mm by 3.00 mm, junction to ambient 63.9 C per watt
Second bodyDRV, WSON, 6 pins, 2.00 mm by 2.00 mm, junction to ambient 72.8 C per watt
Reel2500 pieces on the DGN body, against 3000 on the DRV body
Temperaturejunction minus 40 to 150 C
DocumentSBVS402, April 2020
Voltage optionsfixed 3.3 V and fixed 5 V, no adjustable member in this family

Electrical parameters that decide the application

Input range3 V to 40 V, with 45 V of transient tolerance for inductive kickback
Output3.3 V fixed, 150 mA
Quiescent current2.7 uA typical at light load and 4.5 uA maximum in the features table
Package splitthe electrical table prints separate quiescent rows for the DGN and DRV bodies, so the maximum to use in a standby budget is the row for the body on the board
Shutdown current0.3 uA typical, 1 uA maximum with the enable low
Accuracyplus or minus 1.5 per cent over line, load and temperature
Dropout180 mV typical at 100 mA
Current limit180 mA minimum, 510 mA typical, 690 mA maximum with the output shorted to 90 per cent of nominal
Undervoltagethe output turns off as the input ramps down at 2.7 V, with 200 mV of hysteresis
Enable thresholds2 V high, 0.7 V low, 10 nA of pin current
Ripple rejection60 dB at 100 Hz with a 0.5 V peak to peak ripple and a 2.2 uF output capacitor
Output capacitor1 uF to 200 uF, a range wide enough to take a small ceramic or a large electrolytic
Thermal shutdown175 C junction with 20 C of hysteresis
Line and load regulation10 mV and 20 mV on the DGN body in the published rows

The four catalogue rows for this family

TPS7B8133DGNR3.3 V fixed in the eight pin HVSSOP body, 2500 piece reel
TPS7B8133DRVR3.3 V fixed in the six pin WSON body, 3000 piece reel
TPS7B8150DGNR5.0 V fixed in the eight pin HVSSOP body, the member for a 5 V sensor or relay rail
TPS7B8150DRVR5.0 V fixed in the six pin WSON body
Body tradethe eight pin body is 63.9 C per watt and the six pin body 72.8 C per watt, which is the only electrical reason to prefer one over the other

Points to check before this part goes on a BOM

Forty volts of input with 45 V of transient tolerance is the reason this part appears on power tool and battery pack boards. An inductive kick from a motor or a relay coil that would take out a 30 V regulator is inside the transient window here, so the clamp and its leakage can come off the board.

The quiescent rows are split by body. The feature list gives 2.7 uA typical and 4.5 uA maximum, and the electrical table prints a separate typical and maximum for the DGN and DRV bodies. A standby budget built from the feature list alone is the wrong number to sign off, because the body on the board decides which row applies.

Dropout of 180 mV typical at 100 mA has to be read against the 150 mA rating. At full load the pass FET is at its limit and the dropout figure that matters is the one in the 150 mA row, not the headline at 100 mA.

A current limit window of 180 mA to 690 mA is wide. The minimum 180 mA is only 20 per cent above the 150 mA rating, so a load that draws a short inrush pulse of 200 mA can trip the limit before the output capacitor is charged. Soft starting the load, rather than raising the limit, is the usual answer.

Undervoltage at 2.7 V falling with 200 mV of hysteresis sets the floor of the usable battery range. On a two cell lithium pack that floor is well below the discharge cut off, so the regulator is not what stops the system, and on a 3 cell alkaline pack it is the point where the cells are already flat.

A 1 uF to 200 uF output window is unusually permissive and it is worth using. A 1 uF ceramic saves board area on a detector, and a 100 uF part on a power tool holds the rail through a motor stall, both without a stability note being needed for either.

What 45 V of transient tolerance buys

A 40 V operating range covers the steady state of a 24 V system and most 36 V packs. The 45 V transient figure covers what happens when the load is inductive: a solenoid, a motor winding or a long cable releasing energy back into the rail.

Without that headroom the board needs a transorb and a series element, and the transorb brings its own leakage and its own capacitance to ground. Removing it also removes the leakage path that quietly drains a battery pack in storage.

Standby budget arithmetic

At 2.7 uA a 5 Ah pack loses about 0.065 mAh a day to the regulator, which is far below the self discharge of the cells. At the 4.5 uA maximum the figure is 0.108 mAh a day, still small, but the two numbers differ by more than half, which is why the maximum row is the one to quote to a customer.

Everything else on the node has to be in the same order for that to matter. A microcontroller in deep sleep at 1 uA and a regulator at 4.5 uA is a node that lasts its shelf life, while the same regulator behind a leaking capacitor is not.

Where this order code fits

This is the regulator behind a smoke detector, a thermostat, a motion sensor or a power tool pack, where the node has to sit for months on a battery and still wake up instantly. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Safety Stock Planning page.

Questions buyers ask

Is the 3.3 V output fixed or trimmed? Fixed, trimmed in test. There is no adjustable member in this family, so a board that needs 2.5 V or 5 V uses the other fixed row or a different part.

Can the output capacitor be a 1 uF ceramic? Yes, the recommended window starts at 1 uF. The effective capacitance after DC bias and temperature is what the loop sees, so a 1 uF part in a small body may measure well under its nominal value at 3.3 V.

What happens on a shorted output? The current limit folds the output back to between 180 mA and 690 mA depending on the part, and thermal shutdown at 175 C takes over if the short stays. The 20 C of hysteresis means the part cycles rather than latching.

Why do the two bodies have different quiescent current? They are different dice in different packages with different thermal paths. The vendor prints both, and the difference is small enough that it only matters on a node where the regulator is the largest standby load.

Does the enable pin need a pull up? The pin draws 10 nA, so a high value resistor is enough to hold it either way. Leaving it floating is not specified and is the usual cause of a node that will not wake.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.