TPS7B8601QDDARQ1
Product Specifications
TPS7B8601QDDARQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7B8601QDDARQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7B8601QDDARQ1: a 500 mA, 40 V automotive regulator with power good and an adjustable output
TPS7B8601QDDARQ1 is a 500 mA low dropout regulator rated to 40 V at the input, built for battery connected automotive nodes that have to survive load dump and cold crank and still draw microamps when the vehicle is parked in a HSOIC body of 8 pins. The adjustable output runs from 1.2 V to 18 V, and the power good delay is set by external components rather than by a fixed internal timer.
Order code and package
| Catalogue string | TPS7B8601QDDARQ1, decoded against the vendor nomenclature TPS7B86xxzQyyyRQ1 |
| Decode | xx is 01 for the adjustable version, z is B for the version with power good, yyy is DDA for the eight pin HSOIC body, and the trailing Q1 marks the automotive grade part |
| Body | DDA, HSOIC, 8 pins with thermal pad, 4.90 mm by 6.00 mm, junction to ambient 41.8 C per watt |
| Second body | KVU, TO-252, 5 pins, 6.60 mm by 10.11 mm, junction to ambient 29.7 C per watt |
| Reel | the document carries the nomenclature and no orderable addendum table, so the reel size has to come from the distributor record or a vendor confirmation |
| Qualification | AEC-Q100 grade 1, ambient minus 40 to 125 C, junction minus 40 to 150 C |
| Leadframe note | the DDA body can ship on more than one leadframe, and the reel label carries ASO FMX for the new site or ASO ASE for the legacy site |
Electrical parameters that decide the application
| Input range | 3 V to 40 V operating, 42 V absolute, which covers a load dump without a clamp in most 12 V systems |
| Output range | 1.2 V to 18 V adjustable, or fixed 3.3 V and 5 V members of the same family |
| Output current | 500 mA maximum |
| Accuracy | plus or minus 0.85 per cent maximum over line, load and temperature, which is a maximum figure and not a typical one |
| Dropout | 475 mV maximum at 450 mA with the output at 3.3 V or above |
| Quiescent current | 17 uA typical at light load |
| Disabled current | 5 uA maximum with the enable pin low |
| Cold crank | plus or minus 2 per cent deviation of the output through a cold crank event |
| Line transient | plus or minus 2 per cent deviation at a 1 V per microsecond input slew |
| Overshoot recovery | the architecture is described as limiting overshoot on recovery from dropout, which is the case that normally pushes a downstream 3.3 V rail over its limit |
| Power good | programmable delay through external components |
| Output capacitor | stable with 2.2 uF or more |
| Thermal | 41.8 C per watt in the HSOIC body and 29.7 C per watt in the TO-252 body |
Family members and the letter that separates them
| TPS7B8601QDDARQ1 | the adjustable member with power good in the eight pin HSOIC body, the part on this page |
| Fixed members | the same family carries fixed 3.3 V and 5 V parts, so a BOM that does not need a divider can use those instead |
| Version letter | no letter means no power good, B means power good, and D means power good with a different pinout |
| Package letter | DDA and KVU are the two bodies, and the thermal numbers differ by more than ten degrees per watt between them |
| Grade | Q1 marks the AEC-Q100 part, and the plain string without Q1 is the industrial row |
Points to check before this part goes on a BOM
The accuracy figure is a maximum, which changes how it is used. A rail specified at plus or minus 0.85 per cent maximum leaves 0.85 per cent for the divider, the reference drift and the load step, and a budget that treats the number as typical will come out short at temperature extremes.
Seventeen microamps of quiescent current is the number that decides whether a node can stay connected while the vehicle is parked. At 17 uA a 60 Ah battery loses about 0.4 mAh a day to the regulator, which is small next to the self discharge of the cell and large next to nothing if the node were built around a regulator drawing milliamps.
The DDA body can arrive on two leadframes from two sites. The reel label is the only place that difference is visible, so a line that has qualified one leadframe thermally should read the ASO field on the label before the reel goes onto the machine.
Cold crank is where a battery connected regulator earns its place. A 2 per cent deviation through the event means a 3.3 V rail stays inside 3.23 V to 3.37 V, which is inside the operating window of most CAN transceivers and MCUs, so the node does not reset when the engine turns over.
Dropout of 475 mV maximum at 450 mA is a maximum over temperature, and it is quoted for outputs at 3.3 V and above. Below that the pass FET has less headroom to work with and the number to check is the one in the lower output rows rather than the headline.
Because the document carries no orderable addendum, a buyer cannot confirm the reel size from it. On a scheduled automotive programme that gap is worth closing with the vendor before the first release, since a 250 piece reel and a 2500 piece reel both ship under strings that look alike.
Where the power good delay comes from
The delay is set outside the part. That is deliberate on automotive nodes, where the same regulator feeds a CAN transceiver on one board and a cluster display on another, and the two need different amounts of time before they are allowed to signal readiness.
A delay that is longer than the rise of the downstream supply prevents a false ready state. A delay that is too long gets noticed at the vehicle level as a slow start, so the value is normally set from the measured rise of the slowest load rather than from the regulator datasheet.
Reading the nomenclature instead of an addendum
With no addendum table in the document, the string has to be checked field by field. The 01 at position seven and eight is the adjustable option, the B after it is the power good version, DDA is the body, R is the reel letter and Q1 is the automotive grade.
A string that does not follow that pattern is either a distributor creation or a different family member. Both are worth a query before a purchase order, because an adjustable part substituted for a fixed one arrives electrically correct and functionally wrong for a board with no divider fitted.
Where this order code fits
This is the regulator on the always on branch of an automotive node, the one that stays powered when the ignition is off and has to survive whatever the battery terminal does during a start. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.
Questions buyers ask
Why is the input range 3 V to 40 V rather than 42 V? 40 V is the operating range and 42 V is the absolute maximum. The gap is small on purpose and means a clamp is still worth having on a 24 V system, where a load dump can go far above either number.
Can the output be set below 1.2 V? No. The adjustable floor is 1.2 V, which is the reference plus the minimum divider ratio the loop is stable with. A 1.0 V rail needs a different family member.
Does the TO-252 body need a heatsink? At 29.7 C per watt and 500 mA it usually does not, provided the copper under the tab is sized for the dissipation. The HSOIC body at 41.8 C per watt needs more copper for the same current.
What happens if the enable pin floats? The enable pin has to be driven; the part is not specified to be off with the pin open. On an always on node the pin is normally tied to the battery through a divider so the node can be shut down in service.
Is the 5 uA disabled current the whole node current? No, it is the regulator current with the enable low. The rest of the node still draws whatever its own shutdown currents add up to, and those often dominate.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.