TPS22910AYZVR
Product Specifications
TPS22910AYZVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22910AYZVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22910AYZVR: a 2 A load switch in a 0.9 mm wafer scale body with reverse current protection that stays active whether the switch is on or off
TPS22910AYZVR is a single P channel switch that connects a 1.4 V to 5.5 V rail to a subsystem, blocks current flowing backwards from the output to the input in both states, and turns off when the input falls below its lockout in a DSBGA body of 4 pins. The YZV body is four bumps on 0.90 mm by 0.90 mm at a 0.5 mm pitch and 0.50 mm height, and the part exists for boards where a load switch is the only component allowed to take up space.
Order code and package
| Catalogue string | TPS22910AYZVR, the A revision of the single channel part and the R letter for the large reel |
| Body | DSBGA, YZV, four bumps, 0.90 mm by 0.90 mm, 0.5 mm pitch, 0.50 mm height |
| Reel | 3000 pieces on a large tape and reel for the R row and 250 pieces for the T row |
| Finish and moisture | SNAGCU bumps, moisture level 1, 260 C, unlimited floor life |
| Temperature | minus 40 to 85 C, which is narrower than the rest of the family and is the first thing to check on an automotive or outdoor board |
| Marking | the A revision rows print a two character code that the reel label carries more clearly than the body |
| Document | SLVSB49F, November 2011, revised January 2015 |
| Family split | four devices in one document, TPS22910A and TPS22912C without a discharge resistor, TPS22913B and TPS22913C with a 150 Ohm one |
Electrical parameters that decide the application
| Input range | 1.4 V to 5.5 V, so the part works from a single cell and from a 5 V rail with one order code |
| Output current | 2 A maximum continuous switch current |
| On resistance | 60 mOhm typical at 5 V, 60.7 mOhm at 3.3 V, 74.2 mOhm at 1.8 V and 83.9 mOhm at 1.5 V, all at 25 C and 200 mA of test current |
| Resistance limits | 80 mOhm maximum at 5 V and 3.3 V, 100 mOhm at 1.8 V and 120 mOhm at 1.5 V at 25 C, rising to 110 and 130 mOhm over the full range |
| Quiescent current | 2 uA typical and 10 uA maximum with the switch on and no load, at 3.6 V and above |
| Off state current | 0.1 uA typical at 3.6 V with the switch off, 1.2 uA typical at 5.25 V, and 7 to 10 uA maximum |
| Reverse protection | an internal comparator disables the switch when the output is driven above the input, and the response is 10 us typical, active in both the on and the off state |
| Lockout | the part turns off when the input falls below its undervoltage lockout, and the lockout is what keeps the output from following a collapsing rail down |
| Enable levels | 1.1 V minimum for a high input when the supply is between 3.61 V and 5.5 V, and 0.4 V maximum for a low input, so 1.2 V logic drives it directly |
| Discharge | no discharge resistor on this device, and 150 Ohm on the TPS22913B and 22913C, which is the only difference that matters for a rail sharing scheme |
| Thermal | 189.1 C per W junction to ambient and 1.9 C per W junction to case, so 2 A at 60 mOhm is 240 mW and a 45 C rise in still air |
| Input capacitor | 1 uF minimum recommended at the input pin, which the four bump body has no room to integrate |
Four devices, two enable polarities and one resistor
| TPS22910AYZVR | 2 A, no discharge resistor, 3000 pieces large reel, the row on this page |
| TPS22910AYZVT | the same device on 250 pieces small reel |
| TPS22912C | the same switch with a different enable polarity, for a rail that has to come on when a controller pin goes low |
| TPS22913B | 2 A with a 150 Ohm discharge resistor, for a rail that must be empty before the next enable |
| TPS22913C | the discharge resistor with the other enable polarity |
| TPS22966 | the dual channel 6 A part in a 3 mm by 2 mm body for a board that needs two switches and more current |
Points to check before this part goes on a BOM
Reverse current protection that works in both states is the reason this part is specified into battery products. A conventional load switch blocks reverse current only while it is off, because the body diode of the P channel conducts when the output is driven above the input. Here a comparator watches the two pins and turns the pass device off when the output climbs, in about 10 us, and it does so whether the enable pin is high or low. That is what lets a subsystem hold its own rail while the main supply is removed without draining the subsystem back into the main rail.
The 10 us response is fast and it is not instant. A hard reversal, such as a battery being inserted backwards or a charger being plugged into a live output, produces a current spike for the duration of the comparator delay, and that spike flows through the body diode before the switch turns off. On a rail with a large output capacitor the spike is short and large; on a rail with a small one it is small. Either way the diode sees it, and a diode that is repeatedly asked to take a spike is a reliability question rather than a data sheet figure.
There is no discharge resistor on this device and that is a deliberate split in the family. A rail with no discharge holds its charge after the switch opens, which is what a subsystem that must retain state wants and what a rail that is re-enabled into a charged capacitor does not. The 22913B and 22913C add a 150 Ohm resistor, which empties a 10 uF capacitor to 5 per cent in about 4.5 ms. Choosing between them is choosing what the next enable sees, not choosing a feature.
The 189.1 C per W junction to ambient figure in a 0.9 mm body is the number that bounds the current. At 2 A and 60 mOhm the switch dissipates 240 mW, which is a 45 C rise in still air, so a 60 C enclosure puts the junction at 105 C against an 85 C ambient rating. The part will work in that corner and it will not work at 2 A on a hot board without copper under the bumps, and the copper under a four bump wafer scale body is whatever the board provides. The 2 A rating is a die rating.
The input range starts at 1.4 V, which is below the threshold of the P channel gate drive at the low end. The resistance rises to 83.9 mOhm at 1.5 V and the maximum is 120 mOhm at 25 C and 130 mOhm over temperature, so a 1.5 V rail at 1 A drops 84 to 130 mV. On a 1.5 V rail that is 6 to 9 per cent of the rail, which is a real constraint on a memory or a radio that expects 1.5 V plus or minus 5 per cent. The part is usable there and the drop has to be budgeted rather than assumed away.
The temperature range stops at 85 C on this device, and that is narrower than the 105 C of the dual channel part in the same catalogue. It is also narrower than most automotive and outdoor specifications. A board that needs a load switch above 85 C ambient has to move to another member, and the move is not a drop in because the bodies differ. This is exactly the sort of parameter that is missed when a part is chosen on current and resistance alone.
Using the reverse protection on a two source board
Two sources feeding one node, a battery and a wall adapter for example, is the classic case for a switch that blocks in both directions. The adapter path has a switch that is on while the adapter is present, and the battery path has one that is on while it is not. When the adapter is inserted, the battery switch sees its output driven above its input and turns off in 10 us instead of conducting through the body diode. The node voltage stays where the adapter puts it and the battery is not charged backwards.
The trap is the sequencing. Both switches must not be on at the same moment during the handover, and the comparator's 10 us is fast enough that a short overlap is survivable. What is not survivable is a board where the enable pins are driven from a comparator with hysteresis that allows both to be on for milliseconds. In that window the higher source charges the lower one through the two switches and the current is limited only by the two resistances and the sources themselves.
What 2 A looks like on a real board
The 2 A figure is a maximum continuous switch current for the die, and the board sets the rest. 240 mW at 2 A in a 0.9 mm by 0.9 mm body has to leave through four bumps into the copper, and a board with a solid plane under the part spreads that heat into a few square centimetres. A board with a narrow trace and no plane gives a rise closer to the junction to ambient figure, which is 45 C at 240 mW and 90 C at 480 mW.
The resistance also moves with current because of the package and the copper. The 60 mOhm figure is measured at 200 mA, which is a small signal measurement. At 2 A the same path is carrying ten times the current and the local heating in the bump and the trace adds to the drop. A calculation that budgets 120 mV of drop at 2 A from the data sheet figure is close to right, and one that budgets 60 mV is not.
Where this order code fits
This is the switch between a main rail and a subsystem that must not back feed it, in a notebook, a tablet, a portable instrument or a battery powered module where the switch has to fit in under a square millimetre Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.
Questions buyers ask
Does it block reverse current when it is on? Yes. The comparator turns the pass device off within 10 us when the output rises above the input, and it does that in both the on and the off state.
Is there an output discharge? Not on this device. The TPS22913B and TPS22913C have a 150 Ohm resistor, and choosing between the two families is a decision about the next enable.
How much current can it pass at 1.8 V? 2 A is the die rating, and the resistance at 1.8 V is 74.2 mOhm typical and 100 mOhm maximum at 25 C, which is 150 to 200 mV of drop at 2 A.
What temperature does it work to? 85 C ambient. That is narrower than the 105 C of the dual channel part and it rules the device out of a hot enclosure.
What logic level drives the enable pin? 1.1 V is enough for a high when the supply is above 3.61 V, so 1.2 V logic works directly. A low is 0.4 V maximum.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.