TPS62231TDRYRQ1
Product Specifications
TPS62231TDRYRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62231TDRYRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62231TDRYRQ1: 3 MHz automotive step down in a 1 by 1.5 mm body
TPS62231TDRYRQ1 is a synchronous step down converter for camera and sensor rails in a SON body of 6 pins. The die sits in a 1.0 mm by 1.5 mm by 0.6 mm package and switches at 3 MHz, which lets a 1 uH inductor and a 4.7 uF output capacitor carry a 500 mA rail in about 12 square mm of board. The input range of 2.05 V to 6 V covers a pre-regulated rail and a lithium cell, and the output is fixed at 1.8 V.
Order code and package
| TPS62231TDRYRQ1 | active, production, SON DRY 6 pins, 5000 pieces on a large reel |
| Reel size | 5000 pieces, not the 3000 used by most of this family |
| Lead finish | NIPDAUAG |
| Moisture level | Level 2, 260 C, one year floor life |
| Temperature | minus 40 to 125 C, AEC-Q100 grade 1 |
| Output | 1.8 V fixed, the 622314 member is 1.5 V in the same body |
Electrical parameters that decide the application
| Input voltage | 2.05 V to 6 V |
| Output current | up to 500 mA peak |
| Switching frequency | 3 MHz nominal, up to 3.8 MHz over the operating range |
| Quiescent current | 22 uA typical in power save |
| Shutdown current | under 1 uA |
| Reference | internal, output fixed by the order code |
| PSRR | up to 90 dB, measured at a stated ripple frequency |
| Duty cycle | 100 per cent for the lowest dropout |
| Start up | 100 us typical soft start |
| Inductor and output capacitor | 1 uH and 4.7 uF, 2.2 uH for higher input voltages |
Family variants and how they differ
| TPS622314-Q1 | 1.5 V output, same body and same pinout |
| MODE pin | high forces PWM across the load range, low enables power save |
| Power save | reduces the switching frequency at light load and holds 22 uA |
| 100 per cent mode | the high side switch stays on when the input falls to the output |
| PWM only | the setting to use in a camera rail where the switching tone matters |
| Package | 1 x 1.5 x 0.6 mm SON with the pad on the underside |
Points to check before this part goes on a BOM
The 500 mA figure is a peak current. Continuous output current at 1.8 V from a 3.3 V input is limited by the inductor current ripple and the switch resistance, and a 1 uH inductor at 3 MHz gives enough ripple that the usable continuous current is below the peak rating at the top of the input range.
PSRR of 90 dB is quoted at one frequency, not across the band. For a camera rail the relevant figure is the rejection at the switching frequency of the upstream converter, usually 1 to 2 MHz, and the datasheet curves there are several tens of dB lower than the headline.
Forcing PWM by holding the MODE pin high removes the variable frequency behaviour at light load and costs quiescent current. In an always-on sensor rail the power save mode is the reason the part was chosen; in a camera rail the forced mode is. The same order code serves both, so the pin strap is a build decision.
The package is 1 mm by 1.5 mm. Dissipation at 500 mA with a 3.3 V input into 1.8 V is about 750 mW at full load, which that body cannot shed without a copper pour under the pad. In practice the rail is a 100 to 200 mA camera supply and the package size is the point.
At 100 per cent duty the part tracks a falling input instead of regulating, which is useful on a battery rail and dangerous on a rail that also feeds a 1.8 V logic domain with a 1.9 V absolute maximum: the output follows the input upward if the input is pulled above the set point by a transient.
The reel carries 5000 pieces rather than the 3000 that most of this family uses. That changes line side handling and the minimum order quantity, and it is the reason a small build sometimes finds this code short while the 1.5 V sibling is in stock.
AEC-Q100 grade 1 covers minus 40 to 125 C ambient. The junction runs above ambient by the dissipation times the thermal resistance, so at 500 mW in a small body the ambient limit is reached before the grade limit.
Replacing a linear regulator
The vendor positions this part against a 1.8 V linear regulator on a 3.3 V rail. The arithmetic is straightforward: a linear part burns 1.5 V times the load current, which at 200 mA is 300 mW in a body that cannot hold it, while the converter burns a fraction of that plus switching loss.
The trade is noise. A converter puts a 3 MHz tone on the rail and a linear regulator does not, so the replacement only works when the load rejects that tone or when a small LC filter follows it.
Reading the current rating correctly
Peak current, continuous current and the current at which the part limits are three different numbers. The first is in the feature list, the second comes from the inductor and duty cycle, and the third is in the electrical table under the high side switch limit.
For a rail that must survive a 400 mA load step without dropping below 1.7 V, the useful figure is the load transient response in the curves, not any of the three numbers above.
Where 3 MHz shows up on the board
At 3 MHz the switching loop has to be small. The input capacitor, the high side switch and the low side switch form a loop that carries a pulse of current every cycle, and anything longer than a few millimetres turns that loop into a radiator that a nearby camera or radio front end will pick up.
The inductor value is also part of the noise story. A 2.2 uH part at the top of the input range lowers the ripple current and the conducted emissions, and the small loss in efficiency is usually worth it in an automotive module that has to pass a conducted emissions scan.
The load side matters just as much. A 4.7 uF ceramic on the output with a short return to the ground pad keeps the transient response flat, while a capacitor placed on the far side of a connector turns the trace inductance into a resonant tank that rings at a few megahertz and shows up as a peak in the emissions plot rather than as a supply problem.
Where this order code fits
The order code is bought for surround view cameras, radar modules and instrument cluster rails where the supply has to fit behind the sensor. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is a 2.2 uH inductor acceptable? Yes, and the vendor recommends it at the higher input voltages because it keeps the ripple current in proportion. The 1 uH value belongs to the 3.3 V input case.
Can the output be adjusted? No. The output is fixed inside the die and set by the order code. A different rail needs the adjustable member of the family or a different part.
What is the MODE pin for? It selects forced PWM or power save. Tying it high keeps the switching frequency fixed and removes the light load tone at the cost of quiescent current.
Does the part need an external compensation network? No. The loop is internally compensated and the output capacitor range is fixed, which is why the vendor gives one capacitor value and one inductor value rather than a table.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.