TPS22925BYPHR
Product Specifications
TPS22925BYPHR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS22925BYPHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS22925BYPHR: a 3 A load switch in a 0.9 mm by 1.4 mm wafer scale package with a 97 us ramp and quick output discharge
TPS22925BYPHR is a single channel load switch that gates a 0.65 V to 3.6 V rail through a 9 mOhm N channel FET with a controlled ramp, so a bulk capacitor downstream charges without pulling the supply down in a DSBGA body of 6 pins. The YPH body is six solder bumps on a 0.5 mm pitch at 0.90 mm by 1.40 mm by 0.40 mm, and the family splits four ways on exactly two choices, how fast the output ramps and whether the output is discharged when the switch turns off.
Order code and package
| Catalogue string | TPS22925BYPHR, the code printed in the page title |
| Body | DSBGA, six bumps, 0.90 mm by 1.40 mm, 0.40 mm height, 0.5 mm pitch |
| Reel | 250 pieces on a small tape and reel. The R letter in this string maps to the small reel in the vendor addendum, and the T letter row, TPS22925BYPHT, is the 3000 piece large reel, which matters on a line that expects a full reel per shift |
| Finish and moisture | SNAGCU bumps, moisture level 1, 260 C, unlimited floor life |
| Temperature | minus 40 to 105 C free air, which is the package rating rather than a junction figure |
| Marking | 12A8 |
| Document | SLVS840D, revised August 2016 |
| Family split | the B rows carry quick output discharge and a 97 us ramp, the C rows keep the discharge and stretch the ramp to 810 us, and the BN and CN rows drop the discharge altogether |
Electrical parameters that decide the application
| Input range | 0.65 V to 3.6 V, so the part works below a silicon bandgap and off a single cell that is nearly flat |
| Resistance at 3.6 V | 9.2 mOhm typical, which is the figure the family name is built around |
| Resistance at 1.8 V | 9.2 mOhm typical, unchanged from the 3.6 V row |
| Resistance at 1 V | 10.2 mOhm typical |
| Resistance at 0.65 V | 13.1 mOhm typical, the worst point in the range and the one to use for a dropout budget on a low battery |
| Continuous current | 3 A maximum switch current, which is a rating of the FET and not a promise about the board |
| Rise time | 97 us typical at 3.6 V on the B rows against 810 us on the C rows, both measured into a 0.1 uF load |
| ON pin thresholds | 1.5 V, 1.8 V, 2.5 V and 3.3 V logic all drive the pin, and hysteresis at 1.8 V runs 82 to 215 mV |
| Quiescent current | 29 uA typical at 3.6 V and 25 C, 49 uA maximum over the full temperature range |
| Shutdown current | 0.5 uA typical and 16 uA maximum with the ON pin at 0 V, which is the figure that decides shelf life |
| Reverse current | minus 0.2 uA with the input and ON pin at 0 V and 3.6 V held on the output, which is what the blocking claim rests on |
| Discharge resistance | the internal pull down on the B and C rows is 150 Ohm, enough to empty a small output capacitor in a few time constants |
| Protection | no current limit and no thermal shutdown appear anywhere in the specification, so a short on the load side is not clamped by the part |
| Thermal resistance | 110.9 C per W junction to ambient on a standard board and 1.2 C per W junction to case, which puts 3 A at 9.2 mOhm at about 0.24 W of conduction |
The four family members and what the letters change
| TPS22925B | quick output discharge present, 97 us ramp at 3.6 V, the row this page describes |
| TPS22925BN | the same silicon with the discharge FET removed, so the output floats when the switch opens |
| TPS22925C | discharge present, 810 us ramp, for a load that needs a softer inrush than the B can give |
| TPS22925CN | no discharge and the slow ramp together |
| TPS22925BYPHR | the 250 piece small reel row used on this page |
| TPS22925BYPHT | the same device on a 3000 piece large reel, which is the string to quote for volume |
Points to check before this part goes on a BOM
A 3 A rating is not a 3 A guarantee on any given board. The current path is the die, the bumps and the copper under them, and 3 A at 9.2 mOhm is 83 mW inside a package the size of a pin head. The 110.9 C per W junction to ambient figure means that 83 mW raises the junction by roughly 9 C on a standard board, and considerably more on a flex with no copper pour. Ask for the copper area before quoting the load.
The reel letter is the trap in this string. TPS22925BYPHR is 250 pieces on a small reel and TPS22925BYPHT is 3000 pieces on a large reel, and both are the same die in the same body. A purchase order that copies the page title gets a small reel, and a line that expects a full reel per shift will stop early. This is the sort of detail worth settling on the offer rather than after the goods land.
Reverse current blocking is the reason this part appears in power path work as well as in simple on off duty. With the switch disabled and the input at 0 V, the body diode path is blocked and the output holds its charge, which lets two supplies share a node without one of them back feeding the other. The blocking works while the switch is off, so a multiplexing scheme that leaves both switches on defeats it.
Quick output discharge is a decision, not a free extra. The 150 Ohm pull down empties the output when the switch opens, which is what makes a rail come back cleanly on the next enable and keeps a peripheral from being held up by a charged capacitor. On a rail that another source also drives, that same resistor is a load on the other source, which is why the N rows exist.
The 97 us ramp is chosen against inrush, not against speed. A 100 uF load charged through a switch that turns on in a microsecond draws an amp for a microsecond and drops the supply for everything else on the rail. At 97 us the same charge is spread over a time the source can supply, and at 810 us the C rows spread it further for a supply that is weaker still. Both are longer than any inrush the load itself produces.
There is no current limit in this device. The data sheet specifies reverse blocking, discharge and the ramp, and nothing else protects the load, so a board that needs a hard short clamped has to add that function outside. It is a deliberate trade: a current limit inside a six bump body this small would cost resistance in the main path, and the family is built for the lowest resistance at 3 A.
Working out whether 3 A is real on a given board
Start from the conduction loss at the actual current and the actual input voltage. At 3.6 V and 3 A the switch is 9.2 mOhm, which is 83 mW. At 1.8 V and 3 A the resistance is the same but the current the supply has to deliver is the same too, so the loss stays at 83 mW while the supply works harder. At 0.65 V the resistance rises to 13.1 mOhm and the loss rises to 118 mW, and that is the point where a small board with two ounces of copper starts to matter.
Then add the ambient. The free air rating is 105 C, which is a package limit and not a junction limit. With 110.9 C per W, a 118 mW loss raises the junction by 13 C on a standard board, so a 70 C enclosure leaves plenty of room and a 95 C enclosure does not. A load switch is often the last part anyone checks for thermal margin, and it is also often the part sitting in the hottest corner of the board next to the connector.
Why the discharge resistor changes a rail sharing scheme
Two switches feeding one node is a normal arrangement for a battery and an adapter, and the discharge resistor is what decides whether that arrangement works. The enabled switch carries the load. The disabled switch presents 150 Ohm from the node to ground, so a node held at 3.3 V by the other source loses 22 mA through the discharge path alone. That current is invisible on a drawing unless the resistor is drawn, and it is the reason the BN and CN rows exist.
On a single source rail the same resistor is an asset. It guarantees that the downstream capacitor is empty before the next enable, so the next ramp starts from zero and the inrush is predictable. Without it a rail that was switched off a second ago can still be holding most of its charge, and the second enable produces a much smaller inrush than the first, which makes an inrush measurement look better than the worst case really is.
Where this order code fits
This is the switch between a battery and a subsystem that has to be powered down completely, in a handset, a solid state drive, a tablet, a wearable or a point of sale terminal Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.
Questions buyers ask
Can it carry 3 A continuously? The die can, and the package can on a board with enough copper under the bumps. 3 A at 9.2 mOhm is 83 mW and 110.9 C per W junction to ambient, so the answer depends on the copper area and the ambient, not on the switch alone.
What happens if the output is held up by another supply? With the switch disabled the part blocks reverse current, so the other supply does not feed back into the input. The 150 Ohm discharge resistor on the B row is still connected to the node, so the other supply sees that load unless the N version is used.
Is there a current limit? No. The data sheet specifies reverse blocking, the controlled ramp and the discharge resistor, and no current limit or thermal shutdown. A load that can short needs protection outside the switch.
Why does the page title end in R? The R is the small reel letter in the vendor addendum, 250 pieces. The same die on a 3000 piece large reel is TPS22925BYPHT. Both are active rows and both are the same part.
What sets the inrush? The 97 us ramp and the output capacitance. A 100 uF load draws an average of about 3.7 A during a 97 us ramp into 3.6 V, which is why the ramp is the feature that keeps the supply from drooping.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.