INA128U2K5
Product Specifications
INA128U2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA128U2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA128U/2K5: the plain grade SOIC on a 2500 piece large reel
The INA128U/2K5 is the plain grade SOIC body on a 2500 piece large reel, the production carrier of this family. The die, the grade and the body are the same as the tube code; what changes is the feeder, the moisture level and the quantity that has to be consumed before the reel is finished. On a board with one channel per unit, a 2500 piece reel is 2500 boards, which is a year for a mid volume instrument.
The electrical summary is the family one: 50 µV maximum offset, 0.5 µV per degree drift, 5 nA bias current, 8 nV per root hertz noise, 120 dB common mode rejection, 700 µA quiescent, gain from 1 to 10,000 with G = 1 + 50 kΩ divided by RG, and a supply window from plus or minus 2.25 V to plus or minus 18 V. The current feedback stage holds 200 kHz at a gain of 100, which is what makes the reel code usable behind a multiplexer rather than only on a slow channel.
The INA128U/2K5 rows as the addendum publishes them
| Part class | Precision instrumentation amplifier, three op amp, current feedback |
| Vendor status | Active, production |
| Data sheet | SBOS051G, revised January 2026 |
| Grade | Plain, the family offset and gain error rows |
| Gain equation | G = 1 + 50 kΩ divided by RG |
| Input offset voltage | 50 µV maximum |
| Offset drift | 0.5 µV per degree maximum |
| Input bias current | 5 nA maximum on the standard rows |
| Voltage noise | 8 nV per root hertz at 1 kHz |
| Common mode rejection | 120 dB minimum |
| Bandwidth | 1.3 MHz at a gain of 1, 200 kHz at a gain of 100 |
| Settling | Quoted against gain on the vendor curve, microseconds at a gain of 100 |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Quiescent current | 700 µA typical |
| Body | SOIC, D outline, 8 pins |
| Carrier | 2500 pieces on a large reel |
| Moisture level | Level 3, 260 degrees, 168 hour floor life |
| Tube sibling | INA128U, 75 pieces per tube, level 2 |
700 µA of quiescent current across a plus or minus 2.25 V to 18 V window
INA128U/2K5 draws 700 µA typical, which is four times the current of the micropower INA126 and a twentieth of what a fully featured instrumentation amplifier usually costs. The supply window of plus or minus 2.25 V to plus or minus 18 V covers a plus or minus 15 V industrial rack and a plus or minus 2.5 V single cell analogue front end in the same part number, and the common mode range tracks the rails rather than sitting at a fixed offset from ground.
The current is flat with load and nearly flat with temperature, so the supply budget can be set from the data sheet row rather than measured. What is not in the row is the reference divider and the load current. A plus or minus 15 V part driving a 10 kΩ load at 10 V adds a milliamp, which is more than the amplifier, and a single supply channel with an unbuffered mid rail divider can add a quarter of a milliamp. The amplifier is therefore rarely the largest item in the budget, and the budget is still small enough that a battery instrument can afford two channels.
Current feedback input stage and bandwidth at a gain of 100
The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA128U/2K5 serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.
Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.
Tubes, reels and two different moisture levels
The SOIC rows ship 75 pieces in a tube or 2500 pieces on a large reel, and the DIP rows ship 50 pieces in a tube. The carrier decides the handling, not the part: a 75 piece tube is a prototype or a small build, and a 2500 piece reel is a production run that will take months to consume. Between those two there is nothing on the addendum, which is why a build of 500 boards is usually bought as several tubes and hand fed rather than as a partial reel.
The moisture level differs between the carriers on this family. The tube rows are published at level 2 with a one year floor life, and the reel rows at level 3 with a 168 hour floor life, so the same die has a different shop floor rule depending on how it arrived. A level 3 reel that is opened for a partial build has to go back into dry storage or be baked, and a 2500 piece reel can easily sit open across two builds. Reading the level off the label rather than off the part number is the practical control, and INA128U/2K5 is the code to check it against.
50 µV of offset and half a microvolt per degree
The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA128U/2K5 can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.
The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.
8 nV per root hertz of voltage noise against 0.17 pA of current noise
The voltage noise row is 8 nV per root hertz at 1 kHz and the current noise is 0.17 pA per root hertz on the standard rows, which places the crossover source resistance at about 47 kΩ. Below that the voltage noise dominates and the amplifier is as quiet as the source; above it the current noise dominates and a FET input part would be quieter. On a 350 Ω bridge the voltage noise is the whole story and 8 nV per root hertz over a 10 Hz bandwidth is 25 nV, which against a 10 mV full scale is 2.5 parts per million.
The 0.1 to 10 Hz noise is quoted as 0.2 µV peak to peak, which is the figure that matters for a slow channel: a 10 mV full scale signal with 0.2 µV of low frequency noise has a resolution floor of 20 parts per million, better than most 16 bit converters can use. A channel that needs more resolution than that is limited by the sensor, and the amplifier stops being the item to change. On INA128U/2K5 the noise is flat enough that a higher gain does not improve the input referred figure below the crossover.
Settling time against gain on a multiplexed front end
The settling time curve on this family is the one to read before a channel is put behind a multiplexer. At a gain of 100 the part settles to 0.01 per cent in a few microseconds, which allows a scan rate in the tens of kilohertz; at a gain of 1000 the same figure stretches out and the scan rate falls with it. The stage before the converter has to settle from the previous channel's value, not from zero, so the worst case is a full scale step between two adjacent channels, and that is the step the vendor curve uses.
The other half of the settling budget is the multiplexer and the filter between it and the amplifier. A 1 kΩ series resistor with a 100 nF capacitor has a 100 µs time constant, which dominates the amplifier completely and is the usual reason a scan runs slower than the data sheet suggests. On INA128U/2K5 the settling figure is only useful when the input network in front of it is faster than the amplifier, and a channel that ignores that rule will show an inter-channel error that moves with the source impedance.
Buying INA128U/2K5 on the reel
A 2500 piece reel is a commitment to a build rate. On a product that ships 500 boards a year the reel is five years of stock under a level 3 floor life, and the amount of baking and dry storage that implies is usually more expensive than buying tubes. On a product that ships 2000 boards a year the reel is a single purchase order and a single feeder setting.
The moisture level is the part of the reel purchase that gets forgotten. Level 3 with a 168 hour floor life means the reel goes back into dry storage between partial runs, and the hours accumulate unless the parts are dried. Our date code management page covers how the floor life is tracked, and the safety stock page covers how many weeks of reel to hold against the schedule.
Questions that arrive with this part number
Whether the reel and the tube carry the same part is the first question and they do, with the moisture level and the carrier as the differences. The second is whether a partial reel can be stored for a year, and the answer is that it can be stored but not used without drying, because the level 3 floor life is a cumulative clock rather than a per use allowance.
The third is about the gain resistor at a gain of 1000, where RG is about 50 Ω and the pin, the trace and the resistor lead are in series with it. A 0.1 per cent metal film resistor placed within a couple of millimetres of the pins is the practical answer, and a longer trace shows up as peaking in the step response rather than as a gain error.