Contact Us

INA128P

Brand: Texas Instruments
Texas Instruments INA128P is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA128P — Power Management & Signal Chain | Superb Automation

INA128P

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA128P from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA128P: the plain grade eight pin plastic DIP in a 50 piece tube

The INA128P is the plain grade of the eight pin plastic DIP in a 50 piece tube, and it is the member of this family that a bench prototype reaches for. The DIP body is 9.81 mm by 9.43 mm, it can be socketed, and it survives being inserted and removed during calibration in a way that a SOIC part does not. The plain grade carries the family offset row of 50 µV maximum and the family gain equation of G = 1 + 50 kΩ divided by RG.

Behind the package the part is a three op amp instrumentation amplifier with a current feedback input stage, 700 µA of quiescent current, 120 dB of common mode rejection, 5 nA of bias current and 8 nV per root hertz of voltage noise, running from plus or minus 2.25 V to plus or minus 18 V. At a gain of 100 the bandwidth is 200 kHz, which is the number that makes this family usable behind a multiplexer and is the reason it is not a general purpose op amp pair.

The INA128P rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, current feedback
Vendor statusActive, production
Data sheetSBOS051G, revised January 2026
GradePlain, the family offset and gain error rows
Gain equationG = 1 + 50 kΩ divided by RG
Gain range1 to 10,000 V/V
Input offset voltage50 µV maximum
Offset drift0.5 µV per degree maximum
Input bias current5 nA maximum on the standard rows
Voltage noise8 nV per root hertz at 1 kHz
Common mode rejection120 dB minimum
Bandwidth1.3 MHz at a gain of 1, 200 kHz at a gain of 100
Input protectionPlus or minus 40 V without damage
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current700 µA typical
BodyPDIP, P outline, 8 pins, 9.81 by 9.43 mm
Carrier50 pieces per tube
Temperature rangeMinus 40 to plus 85 degrees

Current feedback input stage and bandwidth at a gain of 100

The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA128P serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.

Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.

700 µA of quiescent current across a plus or minus 2.25 V to 18 V window

INA128P draws 700 µA typical, which is four times the current of the micropower INA126 and a twentieth of what a fully featured instrumentation amplifier usually costs. The supply window of plus or minus 2.25 V to plus or minus 18 V covers a plus or minus 15 V industrial rack and a plus or minus 2.5 V single cell analogue front end in the same part number, and the common mode range tracks the rails rather than sitting at a fixed offset from ground.

The current is flat with load and nearly flat with temperature, so the supply budget can be set from the data sheet row rather than measured. What is not in the row is the reference divider and the load current. A plus or minus 15 V part driving a 10 kΩ load at 10 V adds a milliamp, which is more than the amplifier, and a single supply channel with an unbuffered mid rail divider can add a quarter of a milliamp. The amplifier is therefore rarely the largest item in the budget, and the budget is still small enough that a battery instrument can afford two channels.

The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm

The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.

The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA128P the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.

50 µV of offset and half a microvolt per degree

The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA128P can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.

The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.

120 dB of common mode rejection and the source imbalance that removes it

The common mode rejection row is 120 dB minimum on the family, measured with a 1 kΩ source imbalance, and it is the number that decides whether a bridge channel can reject a 50 Hz disturbance. Rejection degrades with source imbalance at roughly 1 dB per 100 Ω above the test condition, so a channel with a 10 kΩ mismatch between the two input legs has thrown away most of the 120 dB. In practice that mismatch comes from the sensor rather than from the board: a 350 Ω bridge with one leg 5 Ω high, or a thermocouple with a 2 kΩ cable resistance on one side only.

The fix is a pair of matched resistors at the input, or a buffer for each leg, or a sensor with a trimmed output impedance. The REF pin is part of the same problem: the vendor notes that 8 Ω in series with REF is enough to degrade rejection on a typical part, so the reference has to be driven from a low impedance source such as an amplifier or a shunt reference with a capacitor, not from a divider alone. On INA128P the rejection also falls with frequency, and the vendor curve of rejection against frequency is the one to read for a switching supply disturbance rather than the dc row.

Plus or minus 40 V of input protection and the bias current return path

The inputs survive 40 V beyond the rails without damage, which covers the ordinary fault of a transducer cable being plugged in while the rack is powered, and it covers a miswired bridge. It does not cover a sustained fault at the supply pin, and it does not protect the source: a 40 V fault drives current through the protection network and into whatever is driving the amplifier, so a series resistor at the connector is still worth the board space. The protection also stops being transparent above roughly a megohm of source resistance.

The bias current return path is the second half of the input requirement. Each input needs a dc path to a defined potential, and a floating source such as a transformer or a capacitive sensor will let the inputs drift until the amplifier saturates. The vendor shows the ordinary arrangements, and the one to avoid on INA128P is a path through a high value resistor on one leg only, because that converts the bias current into a differential offset. Matched paths on both legs, or a path to the reference rather than to ground, keep the error common mode.

Buying INA128P in the DIP

Fifty pieces in a tube is a prototype quantity and it is also the quantity that a socketed bench fixture consumes over a year. The carrier is the reason this code exists: a DIP that is inserted by hand into a socket is a calibration and service strategy, and a production board that never sees a socket should use the SOIC code with the same die. The two are electrically identical and only the footprint and the process change.

The plain grade is right when the channel has a trim or when the full scale is large. On a 10 mV full scale the 50 µV offset is half a per cent of the range, which is small enough to live with, and the 0.5 µV per degree drift is 0.2 per cent over 40 degrees. A channel that needs better than that is a different part, not a different grade. Our amplifier cross reference page lists the parts we compare when the DIP cannot be found.

Questions that arrive with this part number

Whether the P and the U codes are interchangeable is the first question and they are on the electrical side, with the same die, the same pinout and the same data sheet, and they are not on the mechanical side, because a DIP footprint will not take a SOIC part. The second question is whether the DIP is worth the second process step on a production board, and it usually is not once the board has moved to reflow.

The third is about the socket. A socket adds resistance in series with the gain resistor pins, and at a gain of 1000 where the resistor is about 50 Ω, a socket contact of an ohm is 2 per cent of gain error. A socketed channel should be calibrated in its socket rather than on a bare board, and the socket should be a turned pin type rather than a stamped contact.