Contact Us

INA126UA-2K5

Brand: Texas Instruments
Texas Instruments INA126UA-2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA126UA-2K5 — Power Management & Signal Chain | Superb Automation

INA126UA-2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA126UA-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA126UA-2K5: the hyphenated spelling of the A grade reel code

This entry is the hyphenated spelling of the A grade reel code, INA126UA-2K5, which the catalogue carries alongside the vendor form with a slash. The part is the A grade SOIC body on a large reel: the tighter offset bin, 175 µA per channel, a gain range from 5 to 10,000 set by one resistor, and the same plus or minus 1.35 V to plus or minus 18 V window as the rest of the family. The spelling is a catalogue artefact rather than a different device, and the page exists so that a buyer who searches either form finds the specification instead of a near duplicate.

The practical consequence of the spelling is at receiving. A distributor confirms an order in the vendor form, a reel label carries the vendor form, and a receiving clerk comparing either string against a purchase order written the other way has to know that the two are the same part. The check that matters is the grade letter and the carrier, not the separator.

The INA126UA-2K5 rows as the addendum publishes them

Part classMicropower instrumentation amplifier, two op amp, single channel
Vendor statusActive, production
Data sheetSBOS062D, revised December 2025
Vendor stringPrinted as INA126UA/2K5 with a slash
Catalogue stringAlso indexed with a hyphen and without a separator
GradeA suffix, tighter offset and gain error window
Gain equationG = 5 + 80 kΩ divided by RG
Input offset voltageFamily row 250 µV maximum, tighter on the A bin
Offset drift3 µV per degree maximum
Input bias current25 nA maximum
Bandwidth200 kHz at a gain of 5, 9 kHz at a gain of 100
Supply rangePlus or minus 1.35 V to plus or minus 18 V
Quiescent current175 µA typical per channel
BodySOIC, D outline, 8 pins
CarrierLarge reel, quantity per the addendum row
Moisture levelLevel 3, 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees
Tube siblingINA126UA in a 75 piece tube

The 80 kΩ term, 0.1 per cent resistors and the resistance you forgot

Gain accuracy on INA126UA-2K5 is set by the external resistor and by the 80 kΩ term inside the equation, and the internal term is trimmed. What is not trimmed is the resistance from the RG pins to the resistor itself: the socket, the solder joint, the trace and the resistor lead all sit in series with RG, and at a gain of 1000 where RG is 80 Ω a single ohm of that path is 1.25 per cent of gain error. That is why the vendor note says sockets and wiring resistance matter at high gain, and why the resistor should be placed within a few millimetres of the pins.

The resistor itself should be a 0.1 per cent metal film part with a 25 ppm per degree coefficient, and it should be the same type on every channel of a multi channel board so that the channels track rather than each drifting its own way. A 1 per cent resistor at a gain of 100 contributes 1 per cent of gain error before temperature, which is larger than the amplifier gain error row. The cost difference between a 1 per cent and a 0.1 per cent resistor is a few cents, and it is the cheapest accuracy in the whole channel.

250 µV of offset and 3 µV per degree of drift on a bridge channel

The offset row for this family is 250 µV maximum on the plain parts and tighter on the A grade, and the drift row is 3 µV per degree maximum. Against a 10 mV full scale bridge those numbers are 2.5 per cent of range and 0.03 per cent per degree, so the offset is trimmed at the bench and the drift is lived with. Against a 100 mV full scale the offset is a quarter of a per cent and the drift is negligible, which is the region where the part is comfortable and where most pressure and flow transmitters actually sit.

The comparison that matters is against the amplifier the part replaces. A general purpose op amp pair built into an instrumentation front end can easily carry 1 mV of offset and 10 µV per degree, and at that level the drift, not the bridge, sets the annual recalibration interval. Moving to a trimmed instrumentation amplifier buys the interval back. The other half of the budget is the bridge excitation: a 5 V excitation on a 350 Ω bridge draws 14 mA, which is two orders of magnitude more than INA126UA-2K5 draws, so the current budget is set by the sensor rather than by the amplifier.

175 µA per channel and the supply window that comes with it

At 175 µA per channel typical and 200 µA maximum, INA126UA-2K5 is built for a product that runs from a battery or from a loop supply, and the supply window of plus or minus 1.35 V to plus or minus 18 V is what makes that possible. The bottom of the window is low enough that a pair of fresh alkaline cells in series will run the part directly, and the top is high enough for a plus or minus 15 V industrial rack. Nothing in between needs a regulator, which is the point: a channel that does not need a regulator does not need the quiescent current of one either.

The current is quoted per channel and with no load, so the total for a dual INA2126 is twice the figure. What the number does not include is the reference divider. A single supply channel needs a mid rail reference, and a 10 kΩ divider across 5 V draws 250 µA, which is more than the amplifier itself. A 100 kΩ divider draws 25 µA and needs a capacitor to hold it stiff; that trade is made once per board rather than once per channel, and it decides whether the microamp budget survives.

Running from plus or minus 1.35 V and what stops working

The supply floor of plus or minus 1.35 V is the reason this family appears in battery instruments, and it comes with conditions. The input common mode window is quoted relative to the rails and does not shrink with the supply, so at plus or minus 1.35 V the window is roughly plus or minus 0.35 V of usable common mode, which is enough for a bridge running at a 0 V common mode and not enough for anything referenced to the positive rail. The output swing also stops about 0.8 V short of each rail, so the usable signal swing at the floor is under a volt peak to peak.

On a 3 V single supply the same arithmetic gives a 1.5 V reference and a signal window of about a volt, which is workable for a strain gauge and marginal for a thermocouple. The part is not a rail to rail amplifier and should not be treated as one. What the low supply does buy is headroom against a dying battery: the amplifier keeps working while the rail falls, and the failure mode is a signal that runs out of range rather than an amplifier that stops.

Bandwidth that falls with gain: 200 kHz at 5, 9 kHz at 100

The bandwidth row is quoted at three gains on this family: 200 kHz at a gain of 5, 9 kHz at a gain of 100 and 1.8 kHz at a gain of 500. That is a steep fall, and it is the price of running the input stage at 175 µA. For a pressure or temperature channel sampled a few times a second it is irrelevant. For a vibration channel or a multiplexed data acquisition front end it is the number that decides whether the part can be used at all, and it has to be read at the gain the channel actually runs rather than at the gain in the headline.

Settling follows the same curve: 30 µs to 0.01 per cent at a gain of 5, 160 µs at a gain of 100 and 1.5 ms at a gain of 500, with a 4 µs overload recovery from a 50 per cent overdrive. On a multiplexed front end the settling time, not the bandwidth, sets the channel scan rate, because the amplifier has to recover from the previous channel before the converter samples. A 16 channel scan at a gain of 100 therefore runs at a few kilohertz at best, and a board that assumes otherwise will show crosstalk that looks like a converter fault.

The DGK body and what a 2.1 mm package means on the line

The DGK suffix is the eight pin VSSOP body, roughly 2.3 mm by 2 mm of body with a 0.65 mm pitch, and it is the smallest of the three bodies this family uses. On INA126UA-2K5 the small body is the reason to choose the part and also the source of most of the process questions: the pins are fine enough that the stencil aperture and the paste volume have to be set for the package rather than for the rest of the board, and the part is not comfortable to inspect without a microscope. A board that also carries 0402 passives will already have the process, and a board that is otherwise 0805 will not.

Thermally the body has little copper to spread heat into, and the part dissipates very little, so the junction stays close to ambient. The number that matters instead is the moisture level: this body is published at level 2 with a one year floor life, which is more forgiving than the level 3 parts on the same board. A reel that sits open over a long build is still a reel that has to be counted, but it does not have to be baked after a weekend.

Buying INA126UA-2K5 and keeping the records straight

Two lines on a purchase order and one line on a reel label are the usual source of a receiving query, and the query is always about the separator or about the grade. Writing the vendor string on the order, quoting the vendor string back at confirmation, and checking the grade letter on the label closes both. A quantity mismatch is the expensive version of the same error and it has nothing to do with the spelling.

The A grade on this code removes a trim on a small full scale channel, and the reel removes a tube feeding operation. Neither changes the electrical behaviour of the board, so a programme can move from the tube to the reel code without requalification. Our incoming inspection plan sets out what is checked on arrival, and the traceability report page covers what is recorded against the reel.

Questions that arrive with this part number

Whether the three spellings are the same part is the first question and they are, with the vendor form carrying a slash and the catalogue carrying both a hyphen and no separator. The second is whether the reel quantity can be confirmed from the code, and on this family it cannot, because the addendum prints small and large reel rows under suffixes that do not line up with the numbers.

The third is about the A grade at temperature. The drift row is the same 3 µV per degree on both grades, so the grade helps at room temperature and does not change the cabinet performance. A channel that fails over temperature fails on the drift row, and no bin of this family fixes that.