Contact Us

INA126EA-250

Brand: Texas Instruments
Texas Instruments INA126EA-250 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA126EA-250 — Power Management & Signal Chain | Superb Automation

INA126EA-250

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA126EA-250 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA126EA/250: the A grade DGK body on a tape and reel, and a suffix that does not mean 250 pieces

The INA126EA/250 is the A grade of the eight pin VSSOP body supplied on tape and reel, and the number at the end of the string is the part most often misread. On this family the vendor addendum prints small reel and large reel rows under suffixes that are not consistent with each other, so a buyer who reads 250 as the quantity can receive ten times more parts than the build needs, or a tenth of what it needs. The quantity has to be named on the purchase order in pieces and carrier, not inferred from the last three characters of the code.

Electrically the part is the family: a two op amp instrumentation amplifier with 175 µA per channel, a gain range from 5 to 10,000 set by one resistor, 250 µV of maximum offset on the plain grade and a tighter bin on this A grade, running from plus or minus 1.35 V to plus or minus 18 V. The DGK body is the smallest of the three this family uses and the reason the code is bought at all on a dense board.

The INA126EA/250 rows as the addendum publishes them

Part classMicropower instrumentation amplifier, two op amp, single channel
Vendor statusActive, production
Data sheetSBOS062D, revised December 2025
GradeA suffix, tighter offset and gain error bin than the plain EA row
Gain equationG = 5 + 80 kΩ divided by RG
Gain range5 to 10,000 V/V
Input offset voltage250 µV maximum on the family row, tighter on the A grade
Offset drift3 µV per degree maximum
Input bias current25 nA maximum
Voltage noise35 nV per root hertz at 1 kHz
Bandwidth200 kHz at a gain of 5, 9 kHz at a gain of 100
Supply rangePlus or minus 1.35 V to plus or minus 18 V
Quiescent current175 µA typical, 200 µA maximum per channel
BodyVSSOP, DGK outline, 8 pins, 0.65 mm pitch
CarrierTape and reel, quantity printed on the addendum row
Moisture levelLevel 2, 260 degrees, one year floor life
Temperature rangeMinus 40 to plus 85 degrees
Dual siblingINA2126 in the 16 pin SSOP carries two of these channels

The DGK body and what a 2.1 mm package means on the line

The DGK suffix is the eight pin VSSOP body, roughly 2.3 mm by 2 mm of body with a 0.65 mm pitch, and it is the smallest of the three bodies this family uses. On INA126EA/250 the small body is the reason to choose the part and also the source of most of the process questions: the pins are fine enough that the stencil aperture and the paste volume have to be set for the package rather than for the rest of the board, and the part is not comfortable to inspect without a microscope. A board that also carries 0402 passives will already have the process, and a board that is otherwise 0805 will not.

Thermally the body has little copper to spread heat into, and the part dissipates very little, so the junction stays close to ambient. The number that matters instead is the moisture level: this body is published at level 2 with a one year floor life, which is more forgiving than the level 3 parts on the same board. A reel that sits open over a long build is still a reel that has to be counted, but it does not have to be baked after a weekend.

Two op amp topology and why the gain floor is 5

The INA126 is a two op amp instrumentation amplifier rather than the three op amp arrangement used by the larger instrumentation parts, and that choice explains most of what is unusual about it. The first stage is a pair of amplifiers sharing one gain resistor, and the second stage is a difference amplifier that removes the common mode. Fewer amplifiers means less supply current, and it also means the gain cannot go all the way down: the minimum stable gain is 5, and the vendor states that a minimum circuit gain of 5 is what keeps the dc common mode range and the bandwidth usable. On INA126EA/250 there is no resistor value that gives unity gain, so a channel that needs a buffer is a different part.

The gain equation is G = 5 + 80 kΩ divided by RG, which is a different shape from the 1 + 50 kΩ form used by the INA128 family. The five is inside the equation, so the external resistor only ever adds to a gain that is already 5. At a gain of 100 the resistor is 842 Ω, at a gain of 1000 it is 80.4 Ω, and at the top of the range the resistor is a couple of ohms, which is where the resistance of the socket and the wiring starts to matter as much as the resistor itself.

Bandwidth that falls with gain: 200 kHz at 5, 9 kHz at 100

The bandwidth row is quoted at three gains on this family: 200 kHz at a gain of 5, 9 kHz at a gain of 100 and 1.8 kHz at a gain of 500. That is a steep fall, and it is the price of running the input stage at 175 µA. For a pressure or temperature channel sampled a few times a second it is irrelevant. For a vibration channel or a multiplexed data acquisition front end it is the number that decides whether the part can be used at all, and it has to be read at the gain the channel actually runs rather than at the gain in the headline.

Settling follows the same curve: 30 µs to 0.01 per cent at a gain of 5, 160 µs at a gain of 100 and 1.5 ms at a gain of 500, with a 4 µs overload recovery from a 50 per cent overdrive. On a multiplexed front end the settling time, not the bandwidth, sets the channel scan rate, because the amplifier has to recover from the previous channel before the converter samples. A 16 channel scan at a gain of 100 therefore runs at a few kilohertz at best, and a board that assumes otherwise will show crosstalk that looks like a converter fault.

Single supply operation and the mid rail that is not optional

INA126EA/250 runs from a single rail as long as the input signal sits inside the common mode window and the output has somewhere to swing. On a 5 V single supply the input window stops roughly 1 V below the positive rail and the output stops about 0.75 V short of it, so the usable span is smaller than the supply suggests. A bridge with a 2.5 V common mode and a plus or minus 20 mV signal fits easily; a sensor that sits at 0.2 V does not, and a channel that has to measure near ground needs either a negative rail or an input level shifted before the amplifier.

The mid rail reference is the second half of the problem. The REF pin has to be driven from a low impedance, because any resistance in series with it turns into a common mode error and a gain error at the same time. The vendor quotes 8 Ω as the point at which a typical part starts to lose common mode rejection, which is low enough that a divider alone is not a reference: the divider has to be buffered, or the reference has to come from a shunt regulator with a capacitor across it.

The 80 kΩ term, 0.1 per cent resistors and the resistance you forgot

Gain accuracy on INA126EA/250 is set by the external resistor and by the 80 kΩ term inside the equation, and the internal term is trimmed. What is not trimmed is the resistance from the RG pins to the resistor itself: the socket, the solder joint, the trace and the resistor lead all sit in series with RG, and at a gain of 1000 where RG is 80 Ω a single ohm of that path is 1.25 per cent of gain error. That is why the vendor note says sockets and wiring resistance matter at high gain, and why the resistor should be placed within a few millimetres of the pins.

The resistor itself should be a 0.1 per cent metal film part with a 25 ppm per degree coefficient, and it should be the same type on every channel of a multi channel board so that the channels track rather than each drifting its own way. A 1 per cent resistor at a gain of 100 contributes 1 per cent of gain error before temperature, which is larger than the amplifier gain error row. The cost difference between a 1 per cent and a 0.1 per cent resistor is a few cents, and it is the cheapest accuracy in the whole channel.

One die, two channels: the INA2126 in the same document

The same data sheet covers the dual INA2126, which is two of these channels in a 16 pin body, and the dual is worth knowing about because a two channel board built from two singles carries twice the part count and twice the placement cost for the same silicon. The dual shares a supply pin pair and nothing else: each channel has its own gain resistor pins and its own reference pin, so the two channels can run at different gains and different references without interacting. Channel to channel crosstalk is specified through the shared supply, and at 175 µA per channel there is very little current to couple.

What the dual does not give is isolation. A single body means a single thermal mass and a single die, so a fault that drives one input beyond the rails heats the whole package, and a channel that has to be protected against a field fault is easier to protect on its own. That is the reason a two channel industrial board often uses two singles even when a dual exists, and it is a decision about the fault path rather than about the price.

Buying INA126EA/250 without guessing the reel

The purchase order should carry the code, the words tape and reel, the piece count and the reel diameter, because the suffix alone does not pin any of them down on this family. A receiving inspection that counts the reel label against the order is the cheapest control against a ten to one quantity error, and it takes a minute per reel. For a build that has to be auditable our component traceability report records the carrier and the reel count against each line, and the incoming inspection plan sets out what is checked at the door.

Questions that arrive with this part number

Whether the last three characters are the quantity is the first question and the answer is no on this family. Whether the EA and the E rows are the same die is the second and they are, with the A suffix marking the tighter offset bin rather than a different silicon, so a channel that has qualified one grade will work with the other and may fail its offset budget.

The third question is about the body. The DGK footprint is not interchangeable with the SOIC D footprint, so a board that was drawn for the D body cannot take this code without a new stencil aperture and a new land pattern, and the two are usually confused because both are eight pin parts with the same pinout.