Contact Us

INA122U2K5

Brand: Texas Instruments
Texas Instruments INA122U2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA122U2K5 — Power Management & Signal Chain | Superb Automation

INA122U2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA122U2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA122U/2K5: the micropower single supply amplifier on a 2500 piece reel

This row is the production carrier of the INA122 family in the SO-8 body: 2500 pieces on a large reel, one tube's worth of handling removed from the line. The electrical rows do not change with the carrier, so the reel is a decision about the build rather than about the circuit: 60 µA, 2.2 to 36 V, rail to rail output, gain from 5 to 10,000 with a single resistor, 250 µV offset and 3 µV per degree drift.

The family is the micropower corner of the instrumentation amplifier market. A part that draws 60 µA and swings rail to rail on a 2.2 V supply is chosen for a portable instrument, and a portable instrument is built in volume, which is why the reel matters. Prototypes run on the tube; products run on the reel.

The INA122U/2K5 rows as the addendum publishes them

Part classSingle supply micropower instrumentation amplifier, two op amp
Vendor statusACTIVE, production data
Data sheetSBOS069B
Catalogue stringINA122U/2K5 with the slash, INA122U2K5 without
Supply range2.2 V to 36 V single or dual
Quiescent current60 µA
Output swingRail to rail
Gain equationG = 5 + 200 kΩ divided by RG
Gain range5 to 10,000 V/V
Input offset voltage250 µV maximum
Offset drift3 µV per degree maximum
Input bias current25 nA maximum
BodySOIC, D outline, 8 pins
Carrier2500 pieces on a large reel
Tube siblingINA122U, tube row for the same body
Grade siblingINA122UA/2K5, tighter bin on the same reel
Moisture levelLevel 3, 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees

The reel size and the build rate have to be read together. At 2500 pieces a reel and 300 boards a month with two channels each, a reel is a little over four months of production, which is a sensible quantity to hold. At 50 boards a month the same reel is two years, and at level 3 with a 168 hour floor life the tail of that reel will have been opened and resealed a dozen times before it is consumed.

Two channels per board and one reel

A differential input instrument often carries two of these amplifiers, one for the signal and one for a reference channel, and that doubles the consumption of the reel without changing the handling. It also makes the grade decision more consequential, because a mismatched pair of channels shows up as a differential error that cannot be calibrated out with a single trim. Ordering both channels from the same reel, with the same date code, is the cheapest way to keep them matched, and it is a discipline that costs nothing at the purchase order stage.

The date code point applies to any dual channel board and is worth stating plainly: two parts from different lots have different offset bins and different drift, and the difference is not in the data sheet because the data sheet describes one part. A production build that places two amplifiers per board should treat the reel as the unit of traceability.

Single supply, rail to rail and the noise floor

At 60 nV per root Hz this is not a low noise part, and it does not need to be for the applications it serves. A load cell with a 2 mV full scale at a gain of 100 produces 200 mV at the output, and the amplifier noise in a 10 Hz bandwidth is about 19 µV referred to the input, which is 1 per cent of the full scale. That is a workable ratio for a weighing instrument built to 0.1 per cent, and it is not workable for a 0.01 per cent instrument, which needs a lower noise part with a higher supply current.

The rail to rail output is what makes a 3 V circuit possible. A part that swings to within tens of millivolts of each rail gives back almost the whole supply as signal range, and on a 2.2 V minimum supply this is the difference between a usable channel and a channel that clips at half scale. The catch, as always with rail to rail outputs, is that the current available near the rail is lower than in the middle of the range, so a heavy load pulls the swing in.

Board rules for a 60 µA part on a reel

A micropower part is sensitive to leakage in a way that a milliamp part is not, because the leakage is compared against 60 µA rather than against 10 mA. A board that has been cleaned badly, or not at all, can show a leakage path from the supply to the input that is a significant fraction of the supply current. The board measures are the usual ones: a keep out around the input pins, no via in the input pad, and the gain resistor close to the part.

The second measure is the reference. On a single supply the output zero is set by the reference pin, and a resistive divider there draws current that is larger than the amplifier's own. A 100 kΩ divider across 3 V draws 30 µA, which is half the amplifier current, so the divider should be as high in value as the bias current allows, or buffered, or replaced with a shunt reference. The choice is a system trade and it should be made before the board rather than after.

Where the reel is the wrong answer

A reel is not automatically cheaper. Below a few hundred pieces per year the carrying cost, the moisture management and the risk of an obsolete tail outweigh the per piece saving, and a tube per build is the better answer. The calculation is not close: a reel that spends two years in a dry cabinet is a reel that has cost the price of the parts plus the cabinet space, and the price saving per piece is a few cents.

The other case where the reel is wrong is a build that will change. A programme in its first year, with a board revision expected, should not commit to 2500 pieces of a part that the revision may not use. A tube covers the first builds and the revision, and the reel comes after the circuit is stable.

Buying INA122U/2K5

The reel is active and the tube is active, and the strings differ by the slash. The grade is the plain bin; the A bin on the same reel is a separate string. A purchase order that says only INA122U/2K5 and expects the A bin has made an assumption that the addendum does not support.

For a portable instrument the documentation that travels with the part matters as much as the part: a medical build needs the material declaration and the traceability, and our medical device components page covers what we collect, while the safety stock planning page covers how a reel is sized against a build schedule.

Questions that arrive with this part number

Whether the reel quantity can be split across two builds is the first question, and it can, as long as the moisture log travels with the reel. Whether the part is available in a smaller reel is the second, and the vendor rows for this body are a tube and a 2500 piece reel, so a smaller quantity means a tube or a distributor split. The third question is the slash, which is cosmetic: both strings are the same part.

The fourth is the noise floor. A customer who needs 10 nV per root Hz will not get it from this family, and the honest answer is to move to a bipolar input part with a higher supply current rather than to add gain in a second stage.