Contact Us

INA115BU

Brand: Texas Instruments
Texas Instruments INA115BU is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA115BU — Power Management & Signal Chain | Superb Automation

INA115BU

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA115BU from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA115BU: the tighter bin of the switched gain amplifier

The INA115BU is the B grade of the INA115 family in the 16 pin wide body SOIC. The circuit is the precision three amplifier instrumentation amplifier with the input stage outputs brought out, so a gain switch can sit at the second stage instead of at the input. The B suffix is the tighter offset and drift bin, and the family numbers are 50 µV of maximum offset, 0.25 µV per degree of maximum drift, 2 nA of maximum bias current, 115 dB of minimum common mode rejection at a gain of 1000, and 40 V of input protection on a supply range from 2.25 V to 18 V.

The carrier is a tube of 40, the reel of the same body is 1000 pieces, and the temperature range is minus 40 to plus 85. The quiescent current is 3 mA maximum, which is the number that matters on a battery instrument with four channels, because four of these plus a converter and a reference is a power budget rather than a single part choice.

The INA115BU rows as the addendum publishes them

Part classThree amplifier instrumentation amplifier, B grade, input stage access
Vendor statusACTIVE, production data
Data sheetSBOS021
Gain equationG = 1 + 50 kΩ divided by RG
Gain range1 to 10,000 V/V
Input offset voltage50 µV maximum on the B row
Offset drift0.25 µV per degree maximum
Input bias current2 nA maximum
Common mode rejection at G = 1000115 dB minimum
Input overvoltage protection40 V without damage
Supply range2.25 V to 18 V total
Quiescent current3 mA maximum
Extra pinsInput amplifier outputs and the gain resistor pair
BodySOIC, DW outline, 16 pins
Carrier, tube row40 pieces in a tube
Carrier, reel row1000 pieces on a large tape and reel
RoHSYes
Lead finishNickel palladium gold
Moisture level, tube rowLevel 3 at 260 degrees on the revision row
Moisture level, reel rowLevel 3 at 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees
Part markingINA115BU
Revision rowINA115BU.A, same body and quantity
Status of both rowsActive, production data

The B grade in this family is the one that holds the 0.25 µV per degree drift figure, which is tighter than the 0.3 µV per degree of the INA114 family. That difference is small in absolute terms and large in a budget: over 40 degrees it is 10 µV against 12 µV, which on a 10 mV full scale is 0.1 per cent against 0.12 per cent.

The second stage is where the accuracy is decided

In a three amplifier instrumentation amplifier the first stage provides gain and the second provides the difference. When the input stage outputs are brought out, the second stage becomes a part of the board rather than a part of the die, and its resistor matching sets the common mode rejection of the whole channel. A 0.01 per cent mismatch in the four resistors of the difference stage is about 86 dB of rejection, which is well below the 115 dB the amplifier itself provides at a gain of 1000. The amplifier is not the limit any more, the resistors are.

That is the trade a customer makes when choosing this part for a switched gain channel. The switch is cleaner and the offset does not change with gain, but the common mode rejection depends on four external resistors that have to be matched over temperature. A thin film network in one package is the usual answer, and its ratio tolerance rather than its absolute tolerance is the specification that matters.

Quiescent current and a four channel battery instrument

At 3 mA maximum per amplifier, four channels are 12 mA before the converter is counted, and a battery instrument that runs for eight hours needs a 100 mAh cell for the amplifiers alone. That is a real constraint on a handheld instrument, and it is the reason a newer family with a lower quiescent current appears in the same category. The INA115 was specified in an era of mains powered instruments, and a battery product should compare it against a part that draws a tenth of the current.

Where the instrument has a mains supply and the channels are few, the 3 mA is irrelevant and the accuracy is worth the current. The decision is about the product rather than the part.

Offset drift across a switched gain channel

The drift of the input stage is 0.25 µV per degree, and it appears at the output multiplied by the gain selected at the second stage. A channel that switches between a gain of 1 and a gain of 100 therefore has a drift that changes by a factor of a hundred when the range changes, and a calibration performed on the low range does not hold on the high range. The practical answer is a calibration per range, or a channel where the high range has its own offset correction.

The second stage contributes its own drift, which is set by the resistor network rather than by the amplifier. A thin film network with a 5 ppm per degree ratio tracking adds 5 ppm of the signal per degree, which at a 1 V output is 5 µV per degree, larger than the amplifier drift. The network, not the amplifier, is the term to specify on a high accuracy channel.

Buying INA115BU

The tube is 40, the reel is 1000, and both are active. The family only exists in this body, so a customer who needs a different package has to change families rather than suffixes. The B grade is the one to quote for a channel with a full scale below about 100 mV, and the A grade is the cheaper answer above that.

Stock is thin enough that a 500 piece order may be filled from a reel, and a reel is 1000 pieces, so the customer either takes the whole reel or waits for a tube. That is the practical shape of the supply for this string, and it is worth telling a customer before they plan a build around 500 pieces.

Questions that arrive with this part number

Whether the BU and the AU are interchangeable is the first question, and they are pin compatible with a different offset bin. Whether the extra pins can drive a multiplexer directly is the second, and they can, provided the multiplexer sees a high impedance and the trace is guarded.

The third is whether the part is suitable for a 3.3 V single supply instrument. It runs at 3.3 V, but the output headroom and the reference arrangement have to be planned, and the quiescent current of 3 mA per channel is a large share of a small battery budget.

For a customer comparing this family against a modern programmable gain part, our amplifier cross reference page sets out the parameters we compare, and the medical device sourcing page explains the traceability we hold for instrument grade parts.

One further point on the second stage: the two feedback resistors and the two input resistors of the difference amplifier should be the same package and the same value, and they should be placed symmetrically about the amplifier. A network in one package does that by construction, and four discrete resistors do it only if the board is drawn that way. A mismatch of 0.01 per cent in those four parts is 86 dB of rejection against the 115 dB the amplifier itself delivers, which is the clearest example of an external part setting the specification.

The switch that changes the gain should be placed so that its leakage current flows into a low impedance node rather than into the summing junction. A leakage of a nanoamp into a 25 kΩ node is 25 µV, which on a 10 mV channel is 0.25 per cent. That is the argument for a reed relay at this position on a channel that measures small signals, and the argument for a CMOS switch on a channel that measures large ones.