Contact Us

INA114BP

Brand: Texas Instruments
Texas Instruments INA114BP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA114BP — Power Management & Signal Chain | Superb Automation

INA114BP

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA114BP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA114BP: the tighter offset bin of the precision amplifier in a plastic DIP

The INA114BP is the B grade of the INA114 family in the eight pin plastic DIP. The die is the same three amplifier instrumentation amplifier with 40 V of input protection and a gain range from 1 to 10,000, and the B suffix is the tighter offset and drift bin: the family specification reads 50 µV of maximum offset and 0.3 µV per degree of drift at high gain, and the B row is the one that holds those numbers over the full temperature range rather than at a single point.

The carrier is a tube of 50, the body is 9.81 by 9.43 millimetres, and the temperature range is minus 40 to plus 85. The lead finish on the current revision row is nickel palladium gold, and the moisture level column reads not applicable because the part is a through hole plastic body rather than a taped surface mount part.

The INA114BP rows as the addendum publishes them

Part classThree amplifier instrumentation amplifier, B grade
Vendor statusACTIVE, production data
Data sheetSBOS014B, revised January 2026
Gain equationG = 1 + 50 kΩ divided by RG
Gain range1 to 10,000 V/V
Input offset voltage50 µV maximum at high gain on the B row
Offset drift0.3 µV per degree maximum at high gain
Input bias current2 nA maximum
Common mode rejection at G = 1000115 dB minimum
Input overvoltage protection40 V without damage
Supply range2.25 V to 18 V total
BodyPDIP, P outline, 8 pins
Carrier50 pieces in a tube
RoHSYes
Lead finishNickel palladium gold
Moisture levelLevel 3 at 260 degrees on the revision row
Temperature rangeMinus 40 to plus 85 degrees
Part markingINA114BP
Revision rowINA114BP.B
Status of both rowsActive, production data

This is the one string in the family where the through hole row carries a moisture level. The revision row reads level 3 at 260 degrees and 168 hour floor life even though the carrier is a tube, which tells the buyer that the parts were taped and re bagged at some point in the flow rather than packed straight from the assembly line. It is not a defect, but it does mean the tube has a clock attached that the other tube rows in the family do not.

What the B bin actually buys on a low level channel

The two bins share a data sheet, a body and a price band that differs by a small margin. The difference appears when the channel is specified at a low full scale. At a 10 mV full scale and a 0.5 per cent target the budget is 50 µV, and the drift over 40 degrees at 0.3 µV per degree is 12 µV, so the initial offset is the dominant term. The B bin starts inside the budget and the A bin may not, which is exactly the case where the premium pays for itself.

At a 1 V full scale the same 50 µV is 0.005 per cent and both bins pass with room to spare. A customer who buys the B bin for a 1 V channel is paying for accuracy they cannot use, and a customer who buys the A bin for a 10 mV channel is buying a trim step in disguise. The full scale of the channel is the first question to ask in a quotation, not the part number.

Through hole, sockets and the thermal EMF question

A plastic DIP is often socketed, and every socket adds a pair of dissimilar metal junctions in series with the input. On a channel measuring tens of millivolts, a few microvolts of thermal EMF per degree of gradient is a real error, and the gradient across a socket is larger than the gradient across a soldered joint because the socket is a poor thermal conductor. The standard fix is to keep the two input paths symmetric so the two junctions sit at the same temperature, which cancels the EMF rather than reducing it.

Where a socket is needed for service, a gold plated contact against the nickel palladium gold lead is the lowest EMF pair available, and the socket should be on the same side of the board as the connector so the thermal path from the connector does not cross one input only.

Protection, common mode and the 40 V rating in a 24 V loop

The 40 V protection rating is what makes this part usable in a 24 V actuator or relay loop, and the distinction between protection and linear range is the one that catches people. The part is protected against damage at 40 V, but the linear common mode range is set by the supply, so a plus or minus 15 V supply gives a common mode range of roughly plus or minus 13 V and a 24 V loop sits outside it. The usual arrangement is a resistive divider in front, which reduces the differential signal by the same ratio and costs the noise budget.

A difference amplifier with a high voltage input, such as the family that handles 200 V of common mode directly, is the alternative to a divider. The trade is accuracy against complexity: the divider needs matched resistors at 0.01 per cent to keep the common mode rejection, and the high voltage part has the matching built in.

Buying INA114BP

The tube of 50 and the active status make this an easy part to hold, and the die is shared with the A bin and with the SOIC bodies, so a shortage in one string can usually be covered from another with a board change. The grade is the constraint rather than the supply.

A customer who has qualified the B bin and receives an A bin substitute will not see the difference in a functional test at room temperature, and will see it in a drift test or in a low level accuracy check. That is why the marking on the body matters on this string more than on most: INA114BP reads on the DIP, and a tube that is labelled B with parts marked A is a substitution that only a temperature test will catch.

Questions that arrive with this part number

Whether the BP and the BU are the same die is the first question, and they are, with the package as the only difference. Whether the part can be used at a gain of 10,000 is the second, and the answer is yes with a 5.05 Ω gain resistor, which is a value that has to be a special order and whose tolerance dominates the gain error.

The third is whether a 5 V single supply works. The part runs from 2.25 V, so 5 V is inside the range, and the output needs a reference above ground to reach the converter.

For a customer moving a low level channel from an A bin to a B bin, our amplifier cross reference page lists the families we compare, and the lead time page explains how a tube quantity is held for a build that is not yet released.

The reference pin on a plastic DIP is the one node that a hand build often gets wrong. It has to be driven from a low impedance source, and on a socketed board the easiest route is a wire from the reference pin to the converter reference rather than a divider on the board. A 10 kΩ divider with a capacitor looks adequate on a bench and shows up as a gain error that changes when the output moves, because the divider impedance is in series with the gain network at the frequencies where the loop gain has fallen.

The other through hole specific point is the lead length. A DIP in a socket adds a few millimetres of lead, and at a gain of 1000 where the gain resistor is 50 Ω, that lead is a fraction of the gain term. A socket that is loose will change the gain as it warms, and the symptom is a channel that is accurate cold and drifts as the instrument warms up.