Contact Us

INA111AP

Brand: Texas Instruments
Texas Instruments INA111AP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA111AP — Power Management & Signal Chain | Superb Automation

INA111AP

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA111AP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA111AP: a FET input instrumentation amplifier in an eight pin plastic DIP

The INA111AP is the plastic DIP member of a high speed FET input instrumentation amplifier family, and the A in the suffix is the looser of the two offset grades. A single external resistor sets any gain from 1 to over 1000, the topology is current feedback so the bandwidth stays usable as the gain rises, and the settling time to 0.01 per cent is 4 microseconds at a gain of 100. Input bias current is 20 pA maximum, which is what makes the part suitable for a source that cannot be loaded, and common mode rejection is 106 dB minimum at a gain of 100.

The A grade is the point to be clear about before a specification is signed. The family is laser trimmed in two bins, and the B grade holds an input offset that is roughly a quarter of the A grade row at the same gain. On a channel with a 10 mV full scale and a 1 per cent accuracy target the difference is 75 µV of headroom, which is enough to matter when the offset of the source and the offset of the converter are already counted.

The INA111AP rows as the addendum publishes them

Part classFET input instrumentation amplifier, current feedback
Vendor statusACTIVE, production data
Data sheetSBOS015, March 1998
Gain equationG = 1 + 50 kΩ divided by RG
Gain range1 to over 1000 V/V
Input bias current20 pA maximum, each input
Input offset current0.1 pA typical, 10 pA maximum
Offset drift5 µV per degree maximum
Common mode rejection at G = 100106 dB minimum
Common mode rejection at G = 180 dB minimum, 90 dB typical
Input noise at 1 kHz13 nV per root Hz, 10 nV per root Hz at 10 kHz
Bandwidth at G = 102 MHz
Bandwidth at G = 100450 kHz
Bandwidth at G = 100050 kHz
Settling to 0.01 per cent4 µs at G = 100
Gain error at G = 1000.15 per cent typical, 0.7 per cent maximum
Nonlinearity at G = 1000.001 per cent typical, 0.005 per cent maximum of full scale
Output swing11 V minimum, 12.7 V typical at 5 mA
Short circuit current25 mA
Capacitive load stability1000 pF
Supply range6 V to 18 V, plus or minus 15 V nominal
Quiescent current3.3 mA typical, 4.5 mA maximum
BodyPDIP, P outline, 8 pins
Carrier50 pieces in a tube, the only carrier the addendum lists
Lead finishNickel palladium gold
Moisture levelNot applicable to this package type
Temperature rangeMinus 40 to plus 85 degrees
Part markingINA111AP

The tube of 50 and the absence of a reel is worth flagging at the quotation stage. This is an eight pin plastic DIP with no surface mount sibling carrying the same reel, so a production build runs on tubes, and a pick and place line that only accepts reels needs a tube feeder or a pre taped supply. The AU suffix in the same family is the SOIC body with a 1000 piece reel, which is the route for volume, and the two differ in the package rather than the die.

Why current feedback keeps the bandwidth at high gain

A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, because the loop gain falls as the closed loop gain rises. This family holds 2 MHz at a gain of 10 and 450 kHz at a gain of 100, which is a much gentler slope, and the reason is the current feedback input stage. The practical consequence is that the same part can serve a unity gain buffer channel and a gain of 1000 transducer channel without a second part number, and the settling time stays in the microsecond range instead of climbing into tens of microseconds.

The trade is stability. A current feedback amplifier is sensitive to the feedback impedance rather than the feedback ratio, so a 50 kΩ gain resistor that works at a gain of 100 will show peaking at a lower gain set by a smaller resistor. The data sheet gain equation is the guide, and the resistor should be a metal film part with short leads, placed within a few millimetres of the RG pins. A 1 per cent carbon resistor with 200 nH of lead inductance is enough to put a step in the frequency response that a sine sweep will not reveal.

What a 20 pA bias current asks of the board

20 pA into a 1 MΩ source resistance is 20 µV of offset, which is comparable with the amplifier's own offset at unity gain. Into 10 MΩ it is 200 µV, and the source resistance rather than the part has become the dominant error. That is the reason the family is specified with a bias current rather than an input current noise figure alone, and it is why the input traces on a board using this part should be short, on the top layer, with no solder flux residue between them.

Offset current of 10 pA maximum is the matching term. If the two source resistances are equal, the bias currents cancel and only the offset current remains, which is why a differential source with a balanced impedance is worth the two extra resistors. An unbalanced source converts the full 20 pA into an error, and that error drifts with temperature because bias current roughly doubles every ten degrees on a FET input.

Overload recovery and the multiplexer in front of it

An instrumentation amplifier fed by a multiplexer sees the full scale of the previous channel at the moment the switch closes. The overload recovery of this family is specified at 50 per cent overdrive, and it is the figure that decides the sample rate of the whole system: a channel that needs 2 microseconds to recover after a 10 V overload cannot be sampled at 500 thousand times a second no matter how fast the converter is. The 4 microsecond settling figure applies after the amplifier is out of overload, so the two numbers add.

The input protection is another consequence of that use. The inputs are protected to within 0.7 V of the rails on the low side and 15 V above the positive rail on the high side, which means a 24 V transducer supply that appears on an input pin during a fault will not destroy the part. What it will do is force the output to the rail, and a converter behind the amplifier sees a full scale code that looks like a real measurement. A series resistor of 1 kΩ and a clamp diode to the rail is the standard guard, and it costs 1 kΩ of source imbalance, which the offset current then turns into a few microvolts.

Buying INA111AP

The string is active, the tube is 50 pieces, and the moisture level is not applicable because the body is a through hole plastic package. A build that needs a thousand pieces is buying twenty tubes, and the handling cost of twenty tubes on a line is real. Where the board can take a surface mount part, the AU suffix in the same family ships 1000 pieces on a reel and carries the same die, so the substitution is a board change rather than a performance change.

The grade question is the one to settle first. The BP suffix is the same plastic DIP with the tighter offset bin, and the price difference is small compared with the cost of a calibration step on the line. If the channel is trimmed at test anyway, the A grade is the cheaper route; if the channel is not trimmed, the B grade is the one that meets a 1 per cent accuracy target over temperature without a pot.

Questions that arrive with this part number

The first question is whether the part can run from a single 5 V supply. It cannot in the sense most people mean: the supply range starts at 6 V total, so a 5 V rail is outside the specification, and the reference pin has to sit inside the output swing rather than at ground. A single 12 V rail with a mid supply reference is the practical single supply arrangement.

The second is whether the 4 microsecond settling figure applies to the A grade. It does, because settling is set by the loop and not by the offset bin, but the A grade reaches that settling from a larger initial error, so a channel that needs 0.01 per cent of a 10 mV signal will see the difference.

For a programme that is moving this part onto a surface mount board, our amplifier cross reference page lists the package variants we can compare, and the lead time page explains how we hold a tube quantity for a build that is not ready to buy a reel.