Contact Us

INA110KU

Brand: Texas Instruments
Texas Instruments INA110KU is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA110KU — Power Management & Signal Chain | Superb Automation

INA110KU

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA110KU from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA110KU: the surface mount member of the fast instrumentation family

The INA110KU is the 16 pin surface mount version of the INA110, published ACTIVE in a 40 piece tube, with the same pin selectable gains of 1, 10, 100, 200 and 500 and the same picoamp input bias current. The specified temperature range is minus 25 to plus 85, the operating range is minus 55 to plus 125, and the quiescent current is 4.5 mA maximum. It is the row to use when the board is assembled on a reflow line and the product needs the speed of this family.

The part sits between two other members of the family on the specification sheet, and the comparison is worth making explicitly. The INA101 has a higher input impedance but is ten times slower. The INA103 is faster still at high gain but has only 60 Ω of differential input impedance. This part has both a very high input impedance and a fast settling time, which is why it is the default choice for a scanned bridge array.

The INA110KU rows as the addendum publishes them

Part classInstrumentation amplifier, surface mount body
Vendor statusACTIVE, production data
Data sheetSBOS147A, September 1986, revised July 2005
Gain range1 to 800, five pin strapped settings
Gain equationG equals 1 plus 40 kΩ divided by the sum of RG and 50 Ω
Initial bias current20 pA typical, 100 pA maximum
Input offset100 µV plus 1000 µV divided by G
Offset drift2 µV per degree plus 20 µV per degree divided by G
Common mode rejection, G equals 170 dB minimum, 90 dB typical
Common mode rejection, G equals 100100 dB minimum, 110 dB typical
Gain error, G equals 1000.02 per cent typical, 0.2 per cent maximum
Bandwidth at G equals 1 and 102.5 MHz
Bandwidth at G equals 100470 kHz
Bandwidth at G equals 500100 kHz
Slew rate17 V per microsecond typical
Settling to 0.1 per cent at G equals 50011 µs
Output into 2 kΩPlus or minus 10 V over temperature
Capacitive load5000 pF stable
Supply rangePlus or minus 6 V to plus or minus 18 V
Quiescent current3 mA typical, 4.5 mA maximum
Thermal resistance100 degrees per watt junction to ambient
BodySOIC, 16 pins, wide body
Tube rowINA110KU, 40 pieces, tube, Active
Moisture levelLevel 3 at 260 degrees, 168 hours floor life
MarkingINA110KU
Temperature, specifiedMinus 25 to plus 85 degrees
Temperature, operatingMinus 55 to plus 125 degrees

Only a tube row appears, at 40 pieces, with no reel string in the addendum. That is a real constraint for a production build: it means the carrier is a tube, and a tube is a manual feed to a pick and place machine or a hand placement. For a board with one of these parts per channel and eight channels, the tube is workable; for a high volume line it is not, and the customer has to plan the placement step around it.

The settling chain in a multiplexed front end

When a multiplexer switches from channel to channel, the amplifier has to settle through the source capacitance, the multiplexer on resistance and its own dynamics. The 4 µs figure at unity gain is measured with a step at the input, and in a real scanner the settling is slower because the source network adds a time constant. A 1 kΩ source and a 100 pF multiplexer capacitance give a 100 ns time constant, which is small compared with 4 µs, so the amplifier dominates.

At a gain of 500 the settling is 11 µs, and that is the number to use for a thermocouple scanner running at high gain. A 16 channel scan at 12 µs per channel is a 5 kHz frame rate, which is faster than any thermal process needs and slow enough that the multiplexer can be a simple CMOS switch.

Working with picoamp inputs

A picoamp input demands a clean board. Flux residue with a few hundred megohms of leakage across the input pins will inject more current than the amplifier's own bias, and the offset will drift with humidity. Conformal coating or a guard ring around the input pins is the standard remedy, and on a 16 pin SOIC the guard ring has to be routed on both sides of the board to be effective.

The input capacitance of 6 pF in differential mode is low for a FET input, so a high impedance sensor with a long cable will form a pole at a frequency that depends on the cable capacitance. A 100 pF cable with a 1 MΩ source is a 1.6 kHz pole, which limits the useful bandwidth long before the amplifier does.

Thermal behaviour and the 100 degree per watt figure

At 4.5 mA of quiescent current and a 30 V total supply, the part dissipates 0.135 W, which at 100 degrees per watt is a 13.5 degree rise above ambient inside the package. That is small, and it is why the offset drift from self heating is not a first order term in this part. The output stage is the larger heat source when it drives a heavy load, and 10 mA into a 1 kΩ load is another 0.1 W.

The surface mount body has a shorter thermal path than the DIP, so the junction runs cooler for the same dissipation, which matters on a board with eight channels packed together.

Buying INA110KU

A 40 piece tube at level 3, no reel. The level 3 rating means the tube has a 168 hour floor life once opened, which for a tube of 40 parts consumed over a week is not a constraint. A tube that is opened for two parts and put back on the shelf needs a bake before the next use if the interval exceeds the window.

The absence of a reel row is the practical limit on volume. A customer building more than a few thousand boards a year should ask the vendor about a tape and reel option, because the addendum as published does not list one.

Questions that arrive with this part number

Whether the gain can be switched in circuit is the first, and it can, by switching the gain pins with a relay or an analogue switch, with the caveat that the switch resistance adds to the 50 Ω internal term and changes the gain. The second is whether the part can drive a 5000 pF load without oscillation. It can, which is unusual and useful for a cable or a filter.

The third is the difference between this row and the ceramic G grade. The G grade is specified over minus 55 to plus 125 and comes in a ceramic DIP, and it is the row to use when the specification has to hold at the extremes. The plastic row is specified over minus 25 to plus 85 only.

Switching the gain pins in circuit has one more consequence worth stating. The pins carry the internal gain network, so a switch that is not fully settled during a conversion injects a transient into the summing node, and the output shows a step that lasts as long as the switch takes to settle. A relay is slow but clean; a CMOS switch is fast but injects charge. For a scanner that changes gain once per frame, the relay is the better choice.

A last point on the tube of 40: it is the only carrier the addendum lists, so a build plan that assumes a reel has to be checked against the vendor current packaging list before the order is placed.

For a scanner that is comparing the family rows, the amplifier cross reference page lists them, and the drop in verification page covers the gain pin differences.