Contact Us

INA110KP

Brand: Texas Instruments
Texas Instruments INA110KP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA110KP — Power Management & Signal Chain | Superb Automation

INA110KP

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA110KP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA110KP: a fast instrumentation amplifier with internal gain settings

The INA110KP is a three op amp instrumentation amplifier in a 16 pin plastic DIP, published ACTIVE in a 25 piece tube, with internal gain settings of 1, 10, 100, 200 and 500 selected by pin strapping and a continuous range to 800 set by one resistor. Its distinguishing feature is speed: 4 µs settling to 0.1 per cent at unity gain, 12 V per microsecond of slew rate and 2.5 MHz of bandwidth at a gain of 1 and also at a gain of 10. Most instrumentation amplifiers at this offset level are ten times slower.

The input stage is a pair of junction FETs, which is why the bias current is measured in picoamps rather than nanoamps and why the settling is fast without a large input capacitance. That combination is what makes the part useful for a scanned array of high impedance sensors, where each channel has to settle quickly after the multiplexer switches.

The INA110KP rows as the addendum publishes them

Part classInstrumentation amplifier with pin selected gains
Vendor statusACTIVE, production data
Data sheetSBOS147A, September 1986, revised July 2005
Gain range1 to 800
Gain equationG equals 1 plus 40 kΩ divided by the sum of RG and 50 Ω
Internal gains1, 10, 100, 200 and 500 by pin strapping
Initial bias current20 pA typical, 100 pA maximum on this grade
Offset current2 pA typical, 50 pA maximum
Differential input impedance5 times 10^12 Ω in parallel with 6 pF
Common mode input impedance2 times 10^12 Ω in parallel with 1 pF
Input offset100 µV plus 1000 µV divided by G, typical
Offset drift2 µV per degree plus 20 µV per degree divided by G
Common mode rejection, G equals 100100 dB minimum, 110 dB typical
Gain error, G equals 1000.02 per cent typical, 0.2 per cent maximum
Bandwidth at G equals 12.5 MHz
Bandwidth at G equals 102.5 MHz
Bandwidth at G equals 100470 kHz
Slew rate12 V per microsecond minimum, 17 typical
Settling to 0.1 per cent, G equals 14 µs
Settling to 0.01 per cent, G equals 15 µs typical, 12.5 maximum
Overload recovery1 µs from 50 per cent overdrive
Output into 2 kΩPlus or minus 10 V over temperature
Output current5 mA over temperature, 25 mA short circuit
Capacitive load5000 pF stable
Supply rangePlus or minus 6 V to plus or minus 18 V
Quiescent current3 mA typical, 4.5 mA maximum
BodyPDIP, 16 pins
Tube rowINA110KP, 25 pieces, tube, Active
Temperature, specifiedMinus 25 to plus 85 degrees
Temperature, operatingMinus 55 to plus 125 degrees

The picoamp bias current is the row that decides the application. A 1 MΩ source with 100 pA of bias produces 100 µV of offset, which is the whole offset budget, so even this part has a source impedance ceiling. Above about 100 kΩ the bias current term starts to dominate, and a part with a femtoamp input is the right choice rather than this one.

The internal gain pins and the 50 Ω term

The gain equation carries a 50 Ω term in series with the external resistor, which is the resistance of the internal gain network that the pin strapping cannot remove. At a gain of 100 the external resistor is 353 Ω, and the 50 Ω term is 12 per cent of the total, so the accuracy of the gain depends on knowing that term. At a gain of 500 the external resistor is 30 Ω, and the internal term is larger than the external one, which is why the pin strapped settings stop at 500.

Using the internal settings removes the resistor from the error budget entirely, and the gain error for a pin strapped setting is specified as a percentage of the setting rather than of the resistor. For a scanned system that switches between gains, the pin strapped settings are also faster to change than a relay and a resistor network.

Speed, settling and the multiplexer

The 4 µs settling at unity gain is what makes this part suitable for a multiplexed front end. A 16 channel scanner with a 5 µs per channel budget can sample all sixteen in 80 µs, which is a 12 kHz frame rate. The same scanner with a 40 µs part would manage 1.5 kHz, and that difference decides whether the instrument can watch a transient.

The bandwidth is flat at 2.5 MHz for gains of 1 and 10, which is unusual: most parts lose bandwidth as gain rises. The reason is that the first stage has a fixed transconductance and the second stage gain is what changes, so the loop gain stays high until the second stage runs out of bandwidth. At a gain of 100 the bandwidth falls to 470 kHz, which is still high for an instrumentation amplifier.

Noise and the FET input

The voltage noise is 10 nV per root hertz at 10 kHz, and the current noise is 1.8 femtoamps per root hertz, which is negligible for any source under a megaohm. That combination is why the part suits a high impedance capacitive sensor: the current noise does not become a voltage noise through the source impedance until the impedance is enormous.

The 0.1 to 10 Hz noise is 1 µV peak to peak, which is low for a FET input amplifier and is the figure that matters for a DC bridge measurement.

Buying INA110KP

A 25 piece tube is the only carrier for the plastic DIP. The surface mount row is the production route, and the ceramic and military grades are separate orderable strings in different bodies. For a small instrument build the tube is exactly the right quantity and it has no moisture sensitivity limit.

The specified range is minus 25 to plus 85, while the operating range in the addendum is minus 55 to plus 125. As with the rest of this family, the addendum figure is the operating limit rather than the specified one.

Questions that arrive with this part number

Whether the internal gain settings can be combined with an external resistor is the first question, and they cannot, because the pin strapping shorts out the network that the external resistor would use. The second is whether the part can run from a single supply. It cannot without a rail splitter, because the input and output ranges are centred on the midpoint.

The third is whether the 800 gain limit can be exceeded. It cannot be guaranteed, because the internal 50 Ω term becomes comparable to the external resistor, and the gain error grows faster than the gain.

The FET input needs protection that a bipolar input does not. The gate of the input transistor will break down if the input is driven more than about 20 V beyond the supply, and a sensor cable that is plugged in while the instrument is powered is exactly that event. A pair of series resistors and clamp diodes to the rails is the standard guard, and the resistors add to the source impedance, which is why they are usually kept under 10 kΩ.

A last point on the package: the plastic DIP has a copper lead frame and a 100 degree per watt junction to ambient figure, so a socketed part in a warm cabinet runs about ten degrees hotter than the same part soldered to a plane, and that difference shows up as a drift that the calculation did not predict at the first thermal cycle.

For a scanned front end that is choosing between this part and a slower one, the amplifier cross reference page lists the family, and the incoming inspection plan covers the grade marking.