Contact Us

DRV8825PWPR

Brand: Texas Instruments
Texas Instruments DRV8825PWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8825PWPR — Power Management & Signal Chain | Superb Automation

DRV8825PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8825PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8825PWPR: 1/32 microstepping bipolar stepper driver rated 2.5 A per winding

DRV8825PWPR is an integrated microstepping bipolar stepper motor driver in a HTSSOP body of 28 pins. It contains two full H-bridges, a microstepping indexer and a current regulator, and it takes step and direction pulses from a controller with no external indexer. The PWP order code is the 28-pin HTSSOP with a PowerPAD on the underside.

Order code and package

Order codeDRV8825PWPR
Package28-pin HTSSOP with exposed PowerPAD, 9.7 mm by 6.4 mm
Packingtape and reel
Motor supply8.2 V to 45 V on VM
Drive current2.5 A per winding at 24 V and 25 degrees ambient
Microsteppingfull step to 1/32 step, set by three mode pins
InterfaceSTEP and DIR pulses, nSLEEP, nRESET, nENBL, nFAULT
Reference output3.3 V regulator for the reference divider

Electrical parameters that decide the application

High side on resistance0.2 ohm typical at 25 degrees, 0.32 ohm maximum
Low side on resistance0.25 ohm typical at 25 degrees
Current chopping frequency30 kHz internal PWM
Current sense blanking4 microseconds
Trip voltage660 mV nominal at the 100 percent setting
Under voltage lockout7.8 V to 8.2 V rising on VM
Thermal shutdown160 to 180 degrees junction
Sleep current10 to 20 microampere on VM

Family variants and how they differ

M0 M1 M2 = 000full step
M0 M1 M2 = 100half step
M0 M1 M2 = 010quarter step
M0 M1 M2 = 001sixteenth step
M0 M1 M2 = 101thirty-second step

Points to check before this part goes on a BOM

The 2.5 A figure is quoted at 24 V and 25 degrees ambient with proper heat sinking, and it is a package limit rather than a silicon limit. At 0.2 ohm high side and 0.25 ohm low side, 2.5 A burns about 1.1 W in one bridge, and the HTSSOP has to pass that through the PowerPAD into the board, so the current a build can hold depends on the copper under the part.

Full scale current is the reference voltage divided by five times the sense resistor, so 1.25 V on xVREF with a 0.2 ohm shunt gives 1.25 A, and 2.5 V gives the headline 2.5 A. Accuracy is degraded below 1 V of reference, so a very low current setting is better reached by a larger shunt than by a smaller reference.

Microstepping changes the current per step, not the thermal budget. At 1/32 step the two windings carry sine and cosine currents of the same peak value, so the total dissipation in the package stays close to the full step case while the mechanical output falls, and a 2.5 A setting is a 2.5 A setting whether the motor is stepping in full steps or in thirty-seconds.

Decay mode selection is the setting that most often surprises a new board. Mixed decay keeps the current loop stable at low speed, fast decay gives up torque for faster current fall, and slow decay lets the current recirculate in the bridge. On a high inductance motor the wrong mode shows up as audible noise and as missed microsteps rather than as a fault flag.

The trip comparator works against a 660 mV nominal threshold at the 100 percent setting and is blanked for 4 microseconds after each switching edge. On a small inductance winding the current rises faster than the blanking window, so the effective current is higher than the set value and the 30 kHz chopper becomes the limit rather than the reference divider.

Under voltage lockout sits between 7.8 V and 8.2 V rising, which is above the 8.2 V bottom of the stated operating range. A 9 V rail that sags under motor acceleration therefore crosses the lockout and the outputs go high impedance, so the supply has to hold above 8.2 V at the trough of the current pulse and not only at no load.

The 3.3 V reference output supplies the divider that sets xVREF, and its load rating is small enough that a low resistance divider loads it. Two 10 k resistors draw 165 microampere, which is inside the rating, while a 1 k pair would not be.

The supply voltage changes the thermal answer more than the current setting does. On resistance is quoted at 24 V, and at 12 V the same 2.5 A setting dissipates less in the bridge but the motor needs twice the current for the same torque, so a 12 V build runs at a lower current setting and a higher duty cycle than the headline figure suggests.

Bulk capacitance at VM is what absorbs the current a stepper returns during deceleration. A driver without enough local capacitance sees VM rise above the 45 V rating when a moving load is braked, and the resulting over voltage event is fast enough that the protection does not report it as a fault, it simply damages the part.

Where this order code fits

The part drives bipolar steppers in printers, scanners, automated teller machines, security cameras, laboratory instruments and small factory automation axes. Teams comparing it with a neighbouring part start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it need an external indexer? No. The indexer is inside and the mode pins select full, half, quarter, eighth, sixteenth or thirty-second step, so a controller only supplies STEP and DIR plus the enable and sleep signals.

What sets the current limit? The analog voltage on xVREF against the sense resistor on xISENSE, with full scale equal to the reference divided by five times the shunt value. The reference should stay at or above 1 V where the accuracy is specified.

Can two motors share one driver? No. Each H-bridge drives one winding of one bipolar motor, so a two motor build needs two devices and two sets of sense resistors.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.