Contact Us

DRV8353SRTAR

Brand: Texas Instruments
Texas Instruments DRV8353SRTAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8353SRTAR — Power Management & Signal Chain | Superb Automation

DRV8353SRTAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8353SRTAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8353SRTAR: 100 V gate drive with three shunt amplifiers on an SPI bus

The DRV8353SRTAR is the SPI member of the 100 V DRV835x family in the 40-pin 6 mm by 6 mm WQFN body. It has three half-bridge gate drivers for external N-channel FETs, three low-side current shunt amplifiers, and a serial port that carries every setting that the hardware variants put on a resistor. That combination is what a drive needs when the current loop is closed in software, when the fault history matters, and when the same board has to run different motors without a rework station.

The amplifiers take the voltage across three external shunts and present it with a gain of 5, 10, 20 or 40 V/V, this time selected in a register rather than by a resistor. A VREF pin sets the amplifier bias, which is how the same channel is configured for bidirectional sensing with a mid rail offset or for unidirectional sensing referenced to ground. Settling to one percent is 0.15 microseconds typical at a 5 V/V gain with a 0.5 V step, fast enough that the sample window of a PWM synchronous ADC is not the limiting factor.

The gate drive is the 100 V block: 50 mA to 1 A source and 100 mA to 2 A sink in seven IDRIVE steps, charge pump at VDRAIN plus 10.5 V with 25 mA average, VGLS at 14.5 V and 11 V at the gate outputs, VDS overcurrent in seven thresholds, gate to source monitoring and a minimum dead time. All of those settings are reachable over the bus, which means a single board can be tuned for a 20 A stage and a 60 A stage by writing registers instead of changing parts.

This member has no buck regulator. The 350 mA converter belongs to the R variants, and a drive that needs a housekeeping rail from the 100 V bus either moves to DRV8353RSRTAR in the 48-pin body or keeps its own converter. The 40-pin body is the compromise: three amplifiers and the bus, without the converter and without the extra pins that the 48-pin outline needs.

Key data for the DRV8353SRTAR

Operating range9 V to 100 V on VM
OutputsThree half bridges for external N-channel FETs
Gate current50 mA to 1 A peak source, 100 mA to 2 A peak sink, 25 mA average
Shunt amplifiersThree low-side channels, gain 5, 10, 20 or 40 V/V in a register, 0.15 us settling to 1 percent
ReferenceVREF pin sets the amplifier bias for bidirectional or unidirectional sensing
InterfaceSPI for configuration and fault readback, plus the nFAULT pin for a hard fault
Gate suppliesVCP at VDRAIN plus 10.5 V, VGLS 14.5 V, gate outputs 11 V
PWM modes6x, 3x, 1x and independent inputs
Sleep current20 uA typical at 48 V VM
Not fittedNo buck regulator on the 40-pin body

Body, packing and marking data

Body40-pin WQFN, the RTA outline, 6.00 mm by 6.00 mm, 0.75 mm maximum height
Carrier2000 pieces on a 330 mm large tape and reel, 250 pieces on a small reel under the RTAT suffix
FinishNIPDAUAG lead finish, moisture level 2 with one year floor life on the plain row, level 1 with unlimited floor life on the A row
TemperatureMinus 40 C to plus 125 C operating
MarkingDRV8353S on the body, lot and date code on the reel label

Reading the code before you buy it

DRV8353 is the circuit with three shunt amplifiers, S is the SPI interface, RTA is the 40-pin 6 mm by 6 mm body, and R is the large reel. Add an R after the circuit name and the part becomes DRV8353RSRTAR, which is the same body with the 350 mA buck. Move to RGZ and the body grows to 48 pins at 7 mm by 7 mm. Three parts, one family, three different board areas.

The moisture row is where this order code differs from the rest of the family. The plain DRV8353SRTAR row reads level 2, 260 C, one year, while the A row of the same string reads level 1 with unlimited floor life, and the marking column for the small reel rows is blank in the addendum. A receiving inspection that reads only the line item can accept either row, and the two rows behave differently once the bag is open.

One more detail belongs in the incoming check. The 40-pin body has 2000 pieces on the large reel, against 2500 for the 48-pin RGZ and 3000 for the 32-pin RTV. A planning sheet that assumes 3000 pieces per reel across the family will over-order on this part by a third, and a line that expects a 330 mm reel for every DRV835x will find one body size that does not match its feeder setting.

Where the DRV8353SRTAR fits

Servo drives that close the current loop in software are the main application, because the three amplifiers and the register set give the controller everything it needs to reconstruct phase current from a low-side shunt. Factory automation axes, collaborative robot joints and linear motor stages all use this pattern, and the ability to change gain and threshold over the bus is what lets one drive board serve several motor sizes.

Battery test equipment and electronic loads use the same part for a different reason: the SPI readback gives a fault history that a test station can log, and the VDS thresholds can be moved between test recipes without a rework. That is a smaller market but a demanding one, because a test instrument that trips without a reason is a support ticket.

Power tools and garden equipment use the 100 V rating as margin on a 48 V pack and drive the FETs directly from a controller that already has an SPI port. The amplifier settling time of 0.15 microseconds matters there, because the current sample has to be taken inside a short PWM window at high duty. Buyers who consolidate several drive boards onto this part usually start from a list of what is available, and the power management cross reference page is where the family comparison starts.

Questions we get on this code

Does the SPI port need to be programmed before the motor can turn? The gate driver has default settings that will drive a motor, but the thresholds and the gain come up at their default values, which may not match the stage. In practice the controller writes the configuration at power up and verifies it by reading the register back before it enables the bridge, which is also the check that catches a bus that is not connected.

Can the three amplifiers measure a phase current that reverses? Yes if VREF is set to a mid rail bias, which is the bidirectional configuration. With VREF at ground the output saturates at zero for a negative current, which is fine for a unidirectional drive and wrong for a regenerative one.

Why is the settling time quoted at 5 V/V? Because the amplifier bandwidth falls as the gain rises, and the vendor quotes the fastest configuration. At 40 V/V the settling is slower, and a current sample taken 0.5 microseconds after the switch edge will be short of its final value at that gain.

Is the buck really necessary? Only if the board has no other rail from the 100 V bus. A drive that already carries a 12 V housekeeping supply does not need it, and the 40-pin part is then the smaller and cheaper choice. The 48-pin part exists for the boards that do need it.

What is the risk of a mixed BOM between the S and H variants? The SPI and hardware parts are different bodies, so a mixed BOM is a mixed board. Where a line has both, a stock control that keeps the strings apart is cheaper than a rework, and our safety stock planning page covers how the two are held without confusing them.