DRV8323RHRGZR
Product Specifications
DRV8323RHRGZR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8323RHRGZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8323RHRGZR: 60 V gate drive, three sense amplifiers and a 600 mA buck in 48 pins
The DRV8323RHRGZR is the fullest member of the 60 V DRV832x family: three half-bridge gate drivers for external N-channel FETs, three low-side current sense amplifiers, a 600 mA buck regulator, and the hardware interface instead of SPI. It arrives in a 48-pin VQFN at 7 mm by 7 mm, which is one body size up from the 40-pin 8323H and two up from the 32-pin 8320H.
The three amplifiers are the reason this variant exists. They sit on the low side of each half bridge, take the voltage across an external shunt, and present it with a gain of 5, 10, 20 or 40 V/V selected on the GAIN pin. Each channel can be wired for bidirectional sensing, which is what a field oriented control loop needs to see the current change sign during a regenerative brake, or for unidirectional sensing with an offset if the controller ADC only reads above ground.
The buck regulator is the second reason. It is an LMR16006X running at a nominal 700 kHz, from an input window of 4 V to 60 V, with an adjustable output from 0.8 V up to 60 V at 600 mA. The switching frequency sits between 595 kHz and 805 kHz over the part spread, the maximum duty is 96 percent, and the peak current limit is around 1.2 A, so a 5 V rail at 300 mA for a controller and a radio is a comfortable load and a 5 V rail at 600 mA is the ceiling with the inductor chosen for it.
Everything else is shared with the family. Peak gate current runs 10 mA to 1 A source and 20 mA to 2 A sink in seven IDRIVE steps, the charge pump holds VM plus 11 V at 25 mA average, 100 percent duty is supported, and the sleep current is 12 uA. The part is aimed at drives where the controller needs a rail, the loop needs phase current, and the board cannot carry a separate buck converter and three op amp channels.
Key data for the DRV8323RHRGZR
| Operating range | 6 V to 60 V on VM for the gate driver, 4 V to 60 V for the buck input |
| Outputs | Three half bridges for external N-channel FETs |
| Gate current | 10 mA to 1 A peak source, 20 mA to 2 A peak sink, seven IDRIVE settings |
| Sense amplifiers | Three low-side channels, gain 5, 10, 20 or 40 V/V on the GAIN pin, bidirectional or unidirectional |
| Buck regulator | LMR16006X, 0.8 V to 60 V output, 600 mA, 700 kHz nominal, 96 percent maximum duty |
| Buck current limit | 1.2 A peak typical, which is the figure that sets the real load ceiling |
| Charge pump | VM plus 11 V regulated, 25 mA average output current |
| PWM modes | 6x, 3x, 1x and independent inputs, 100 percent duty supported |
| Sleep current | 12 uA typical |
| Logic | 1.8 V, 3.3 V and 5.0 V CMOS inputs |
Body, packing and marking data
| Body | 48-pin VQFN, the RGZ outline, 7.00 mm by 7.00 mm, 0.9 mm maximum height |
| Carrier | 2500 pieces on a 330 mm large tape and reel, 250 pieces on a 180 mm small reel under the RGZT suffix |
| Finish | NIPDAU lead finish, moisture level 2, 260 C peak reflow, one year floor life |
| Temperature | Minus 40 C to plus 125 C operating |
| Marking | DRV8323RH on the body, lot and date code on the reel label |
Reading the code before you buy it
DRV8323 is the circuit with three sense amplifiers, R is the buck regulator, H is the hardware interface, RGZ is the 48-pin 7 by 7 body, and the final R is the large reel. Change the H to an S and the part becomes DRV8323RSRGZR, which is the same physical body with the SPI port enabled, so this is one of the few places in the family where the interface can be changed without changing the footprint.
What cannot be changed on the same board is the buck. DRV8323HRGZR is the same interface and the same body without the converter, and it is listed at 2500 pieces on a large reel exactly like the R version. Teams that start with the buck and later decide they do not need it, or the other way round, keep the same pad pattern and simply do not fit the inductor and the feedback divider. That is a rare kind of flexibility in a motor driver family and it is worth confirming on the drawing before an approved vendor list is frozen.
The gain pin deserves a note of its own. It is a four level input set by a resistor to DVDD, to ground, or by two intermediate divider values, so a change of gain is a resistor change. The amplifier bandwidth and the offset move with the gain setting, which means a board tuned at 20 V/V and reworked to 40 V/V will read a larger signal and a larger offset at the same time.
Where the DRV8323RHRGZR fits
Servo drives and e-bike controllers with field oriented control are the natural home, because they need all three phase currents and a controller rail from the same 48 V or 60 V bus. Cordless vacuum cleaners and power tools use the buck for the controller and the sense amplifiers for the stall detection that keeps the tool from burning a winding when the brush bar jams.
Drone and robotics propulsion use the same parts at a lower voltage and a much higher current, and there the buck output usually feeds a flight controller that wants 5 V at a few hundred milliamps. That load sits close to the 600 mA rating, so the inductor, the output capacitor and the thermal path under the RGZ body all have to be sized together rather than one at a time.
The 48-pin body also buys routing room that the 32-pin part does not have: three sense lines, the buck switch node and its feedback divider all need to stay away from the gate drive traces, and the extra pins let the analog side of the board sit on one edge. Buyers comparing the family usually start from a cross reference, and the power management cross reference page lists what swaps by body and what needs a new board.
Questions we get on this code
Is 600 mA enough to run a controller and a radio? A Cortex-M4 at 120 MHz draws under 40 mA, a 2.4 GHz radio adds 120 mA in transmit, and an SD card can pull 100 mA in a burst. The sum fits, the peak does not always, so the output capacitor has to carry the burst and the 1.2 A current limit has to be far enough above the steady load to avoid a hiccup on every transmit slot.
Why does the sense amplifier have four gain steps instead of a programmable one? Because it is set by a resistor on a hardware part, and four steps cover the common shunt values with a 3.3 V ADC. A 1 mOhm shunt at 20 A gives 20 mV, which needs the 40 V/V step to reach 0.8 V; a 10 mOhm shunt at 2 A gives the same 20 mV, and the same step works.
Can the buck be disabled and the inductor removed? The gate driver still needs the pins to be at a defined potential, and the vendor document treats the converter as part of the part. Removing the inductor without moving to the non R variant leaves a switch node floating, which is a board that fails on the bench rather than in the field.
What is the difference against the SPI version for a production line? The hardware part has no registers to program, so the test station verifies resistor values rather than a register map, and there is no code dependency at first power up. The SPI part gives fault history and per event configuration, which matters for a drive that has to log why it tripped.
When the 48-pin part is on allocation and the board can grow slightly, the question becomes what can be built this month, and our component lead time page covers the second source routes that keep a line running without changing the drive circuit.