Contact Us

HXN40040

Brand: Hisiwell
Hisiwell HXN40040 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXN40040 — Discrete & Power Semiconductors | Superb Automation

HXN40040

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXN40040 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXN40040: 398 W on the 3.1 to 3.4 GHz window

The HXN40040 is the largest 54 to 56 dBm step on the 3.1 to 3.4 GHz window and the last 12 dB part before the wider 57.5 dBm member. Saturated output is at least 56 dBm, which is 398.1 W, with 12 dB of gain and at least 48 per cent typical drain efficiency from a 50 V rail, in 100 microsecond pulses at 10 per cent duty, with plus or minus 0.8 dB of flatness across 300 MHz.

At 48 per cent the rail supplies 829.4 W during the pulse, the drain current is 16.59 A at 50 V, and the heat is 431.3 W. That is a four hundred watt radio and a four hundred watt heater in the same flange, keyed in 100 microsecond bursts, and every part of the assembly has to be built for 16.6 A of pulse current.

On a 10 per cent duty the average dissipation is 43.1 W and the average current 1.66 A. The average is manageable on a good carrier; the peak is what decides the feed, the capacitor bank, the flange and the die attach, and none of those can be sized from the average.

The efficiency row is the cost of this step. Two hundred watts more output than the 54 dBm member on the same window, for two points less efficiency, means the heat rises from 205.5 W to 431.3 W, a factor of 2.1 for a factor of 1.59 in radio frequency. That is the normal shape at the top of a power ladder, and it is why the largest part is not automatically the cheapest way to reach a given power.

The parameter rows Hisiwell publishes for HXN40040

Part classGallium nitride power transistor, internally matched
Frequency range3.1 to 3.4 GHz
Bandwidth, calculated300 MHz, 9 per cent fractional
Saturation output power as publishedat least 56 dBm
Saturation output power in watts, calculated398.1 W
Gain as publishedat least 12 dB
Drain efficiency as publishedat least 48 per cent, typical
Drain voltage50 V
Flatness across the bandplus or minus 0.8 dB
Operating modepulsed, 100 microsecond width at 10 per cent duty
Input impedance50 ohm
Output impedance50 ohm
Output at 1 dB compressionnot published, the index prints a slash
DC input at saturation, calculated829.4 W
Drain current at saturation, calculated16.59 A at 50 V
Dissipation during the pulse, calculated431.3 W
Average dissipation at 10 per cent duty, calculated43.1 W
Average drain current at 10 per cent duty, calculated1.66 A
Charge drawn per 100 microsecond pulse, calculated1.66 mC
Drive power for the rated output, calculated44 dBm, 25.1 W
Dissipation if efficiency falls to 45 per cent, calculated486.6 W
Thermal resistance, junction to casenot published
Transient thermal impedancenot published
Package outline and dimensionsnot published in text, one image on the product page
Scattering parametersnot published
Pinch off voltage and gate bias pointnot published on this page
Operating and storage temperaturenot published
Moisture level and floor lifenot published
Orderable addendum and packingnot published
Neighbour below at 251 W and 55 per centHXN40039 on the same window
Neighbour above at 562 W and 13.5 dBHXN42013 over 3.1 to 3.5 GHz on a 48 V rail

Twenty five watts of drive and sixteen amps of pulse current

Twelve decibels of gain at 398 W means 25.1 W of drive, which is a power stage in front of this part rather than a packaged amplifier. On the same window the 251 W member needs 12.6 W, so the step to 398 W doubles the driver as well as the heat, and a chain planned around this part has three stages: a small signal front end, a 25 W driver and this flange.

Sixteen point six amperes through a flange, a bond wire array and a feed is a packaging question. The vendor publishes one outline image and no dimension table, so the pin arrangement and the current path have to be established with the vendor before the assembly is fixed. A feed with the wrong inductance limits the pulse edge before the device does, and a flange with the wrong pin orientation will not fit at all.

The charge drawn per pulse is 1.66 mC, so a rail allowed to sag 2 V needs 0.83 mF close to the device and a rail allowed 1 V needs twice that. At 16.6 A of leading edge current the ESR of the bank and the geometry of the loop produce a droop that appears as a power slump at the start of every pulse, which is the most common reason a 56 dBm part measures 55 dBm in a system.

The drive side has the same problem in a smaller size: 25.1 W of drive with a plus or minus 0.8 dB band has to stay inside the linear window of the driver, and the driver itself needs a compression point above the level it is asked to deliver.

Four hundred watts of heat in a hundred microseconds

Average dissipation of 43.1 W is easy to remove; 431.3 W inside each pulse is not, and with no transient thermal impedance published the excursion cannot be computed. The defensible route is a measured case temperature at the rated pulse condition on the first article, and a die attach and carrier chosen for the transient rather than for the average.

The comparison worth making is with the 251 W member. Two hundred watts more radio frequency costs 226 W more pulse heat, 100 W of which is the efficiency difference and the rest is the extra output. On a system that does not need the last 2 dB, the smaller part on the same window is the cheaper build, and the case where the larger part wins is a system that has already paid for the cooling and the 25 W driver.

Efficiency at 45 per cent raises the pulse heat to 486.6 W and the current to 17.69 A, which is 13 per cent more heat in the same flange. The typical marker on the efficiency row means this is a number to specify rather than to hope for.

Where a 398 W pulse stage at 3.1 to 3.4 GHz fits

The fit is a long range radar, an instrumentation radar for range and cross section work, a satellite ground station high power driver or a laboratory load pull amplifier. Three hundred megahertz around 3.2 GHz is a radar window, and 398 W in 100 microsecond pulses is enough for a surveillance front end with a modest antenna.

It is a poor fit for a compact airborne unit without a liquid or heat pipe path, for continuous wave, for a long pulse at the same duty, and for a system whose driver cannot produce 25.1 W with stability. Our RF power transistor cross reference work carries the output, efficiency, rail and drive of the 3.1 to 3.4 GHz members in one table, and the defence grade component supply view covers the screening and temperature class questions that go with a radar build.

Where the next step up is being considered, the 57.5 dBm member on 3.1 to 3.5 GHz delivers 562 W at 13.5 dB of gain from a 48 V rail, which is a different supply voltage and a different match, so the step is not a drop in replacement and should not be planned as one.

Questions we answer on HXN40040 before a lot is booked

The first is the flange. At 16.6 A of pulse current the outline, the pin arrangement and the mounting torque are part of the device, and the vendor has not published them.

The second is the pulse condition. One hundred microseconds at 10 per cent is the published row; a longer key or a higher duty is a different thermal question at 431 W.

The third is the lot. With no orderable addendum and no marking code, the purchase order names the band, the rail and the pulse condition, and the incoming inspection plan records the flange and the DC behaviour of each lot. The RF procurement process puts the droop allowance and the cooling interface in front of the vendor before the first shipment.