DRV8323HRTAR
Product Specifications
DRV8323HRTAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8323HRTAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8323HRTAR: A 60 V Smart Gate Driver With Three Shunt Amplifiers and Pin Set Drive Strength
DRV8323HRTAR is a three phase smart gate driver with three current sense amplifiers in a WQFN (RTA) body of 40 pins. It drives three high side and three low side N channel FETs from a rail up to 60 V, and the H letter means the settings are pins rather than registers, so there is no serial port to program and no firmware to write before the first spin. Drive strength is one of seven settings between 10 mA and 1 A of source current, the three shunt amplifiers offer 5, 10, 20 or 40 V/V, and the part manages dead time itself with a handshake between the two gates of each half bridge.
Order code and package
| Ordering string | DRV8323HRTAR |
| Family document | DRV8320, DRV8320R, DRV8323, DRV8323R, SLVSDJ3D, revised March 2022 |
| Package | WQFN (RTA), 40 pins, 6.00 mm by 6.00 mm |
| Reel and packing | 2500 pieces on a large reel |
| Lead finish and moisture | NIPDAU, level 1 at 260 C with unlimited floor life |
| Temperature range | minus 40 to plus 125 degrees |
| Body marking | DRV8320RS, shared across the family |
| Small reel option | DRV8323HRTAT, 250 pieces |
| Interface | Hardware pins, seven drive strength settings |
| Current sense | Three low side shunt amplifiers on this member |
| Buck regulator | Not on this member, the R variants add it |
| Charge pump | Integrated, for 100 per cent duty on the high side |
Electrical parameters that decide the application
| Operating voltage | 6 to 60 V for the gate driver |
| Variant note | The document also quotes 4 to 60 V for the DRV8320 members |
| Gate drive source current | 10 mA to 1 A in sixteen settings on the serial version |
| Gate drive sink current | 20 mA to 2 A in the same sixteen settings |
| Settings on this hardware version | Seven drive strength settings within the same range |
| Shunt amplifier gain | 5, 10, 20 or 40 V/V |
| Drive time | 500 ns, 1000 ns, 2000 ns or 4000 ns before the gate current drops to the hold value |
| Hold current | 10 mA after the drive time, to keep the FET on without holding the full charge current |
| Dead time | Four extra settings of 50, 100, 200 or 400 ns added on top of the automatic insertion |
| VDS overcurrent levels | Sixteen settings starting at 10 mV |
| Enable to output ready | 40 us with the rail above the UVLO and the enable at 3.3 V |
| Protection | UVLO, charge pump undervoltage, VDS overcurrent, gate driver fault, thermal warning and shutdown |
Family variants and how they differ
| DRV8323H | This part, hardware interface, three shunt amplifiers |
| DRV8323S | The same silicon with a serial port and sixteen drive strength settings |
| DRV8323R | Adds a buck regulator in the 48 pin body |
| DRV8320 | One shunt amplifier configuration, in the 32 pin body |
| DRV8320R | The buck version of the 8320, in the 40 pin body |
| DRV8353 | A later family with a higher voltage rating and a different gate drive architecture |
Points to check before this part goes on a BOM
The H letter is the reason this part needs no firmware. Drive strength, gain and the VDS level are set by resistors on pins, which is what a small team wants for a first board, while the S letter exposes sixteen settings through a serial port and needs a configuration sequence before the first PWM edge. The two are not interchangeable on a board, because the pins carry different functions.
Sixteen drive strength steps become seven on this version, and that is still enough for most FETs. The source current sets how fast the gate rises, which sets the switching loss and the radiated emission at the same time, so the setting is a trade rather than a maximum. A large module with 100 nC of gate charge wants the top of the range, and a small FET in a dense board wants the bottom.
The drive time and the hold current are a two stage gate drive, and they are the part that most people miss. For 500 ns to 4000 ns the driver pushes its full current into the gate, then drops to 10 mA to hold it on. That keeps the gate charged through a long on time without burning the driver, and it means the gate resistor is chosen for the first stage only.
Dead time here is not a fixed number. The driver monitors the gate voltage of the FET that is turning off and only lets the other one start when that voltage has fallen, so the window adapts to the FET and to the temperature instead of being a guess in a register. Four digital settings of 50, 100, 200 and 400 ns are added on top of that automatic insertion, which is the number to use when a slow module needs a wider guard band.
The three shunt amplifiers are the reason to take the 8323 rather than the 8320. Each one measures the drop across a low side shunt with a gain of 5 to 40, and the outputs are analogue voltages for an ADC. The output swings inside a window set by the VREF pin, so a bidirectional measurement is biased to half of VREF on the hardware version and the ADC sees a signal centred rather than sitting on ground.
Where a smart gate driver is worth the extra pins
A 48 V or 60 V three phase drive with a 3.3 V controller is the target. The part makes its own gate supply from the motor rail with a charge pump, drives six FETs with a programmable edge rate, measures three phase currents on low side shunts and reports a fault on one pin. That is a complete power stage control block in 6 mm by 6 mm, which is what a compact pump, fan or actuator needs.
The 60 V rating fits a 48 V bus with the regen margin, and the 6 V floor keeps it away from single cell operation. A 12 V automotive rail needs a clamp in front because the absolute maximum is below a load dump, and the charge pump capacitors have to be rated for the highest rail the clamp allows.
What a replacement has to match
The body and the pin functions, not just the family name. The 8320 in 32 pins, the 8323 in 40 and the 8323R in 48 are three different footprints with different pin outs, and the R variants move pins to make room for the buck. A list that treats them as one part will get a board that does not fit.
The second item is the sense arrangement. This part expects three low side shunts and brings out three amplifier outputs. A board built for a single shunt, or for inline sensing, needs a different member of the family and a different set of pins, and the current loop in the firmware changes with it.
Where this order code fits
The part suits a 24 V to 48 V three phase power stage that needs three current readings and no configuration firmware, in a body small enough to sit beside the FETs. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does the H version need a serial port? No. Drive strength, gain and the overcurrent level are set by resistors on pins, so the part runs from the enable pin and the PWM inputs alone. The S version is the one that needs a configuration sequence.
Can it hold a high side FET on at 100 per cent duty? Yes, the charge pump keeps the high side gate supplied without a bootstrap refresh, which is the difference between this family and a bootstrap only driver at very low modulation.
Are the shunt amplifiers on all three phases? Yes on this member, one per low side leg, with a gain of 5, 10, 20 or 40 V/V. The DRV8320 has fewer of them, which is the first thing to check in a cross reference.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.