DRV5055A2QDBZR
Product Specifications
DRV5055A2QDBZR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5055A2QDBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5055A2QDBZR: A Linear Hall Sensor With 50 mV per Millitesla and a Ratiometric Output
DRV5055A2QDBZR is a ratiometric linear Hall effect sensor in a SOT-23 (DBZ) body of 3 pins. It converts a magnetic field into an analog voltage that sits at half the supply with no field present, moving 50 mV per millitesla over a plus or minus 42 mT range at 5 V, with a 20 kHz sensing bandwidth and a quiescent output that tracks the supply so a ratiometric converter cancels the rail error.
Order code and package
| Ordering string | DRV5055A2QDBZR |
| Family | DRV5055 linear Hall sensor, document SBAS640C revised June 2026 |
| Package | SOT-23, DBZ body, 3 pins, 2.92 mm by 2.37 mm nominal |
| Second package | TO-92, LPG body, 3 pins, 4 mm by 1.52 mm, as DRV5055A2QLPG |
| Reel and packing | 3000 pieces on a large reel, tin lead finish |
| Moisture level | Level 2, 260 C peak, one year floor life |
| Part marking | 55A2 |
| Temperature range | Minus 40 to plus 125 degrees |
| Supply | 3.3 V or 5 V, with every sensitivity quoted at 5 V |
| Suffix meaning | The A prefix carries magnet temperature compensation, the Z prefix does not |
Electrical parameters that decide the application
| Sensitivity at 5 V | 50 mV per millitesla on this A2 member |
| Sensing range at 5 V | Plus or minus 42 mT, which sets the travel the magnet has to span |
| Other sensitivity options | 100 mV per mT at plus or minus 21 mT, 25 mV per mT at plus or minus 85 mT, 12.5 mV per mT at plus or minus 169 mT and 66 mV per mT at plus or minus 75 mT |
| Quiescent output | Half the supply voltage with no field applied |
| Ratiometric behaviour | The quiescent point and the sensitivity both scale with the supply |
| Sensing bandwidth | 20 kHz, which is fast enough for a current sensor in a switching stage |
| Output drive | Plus or minus 1 mA, so the load has to be a high impedance converter input |
| Supply current | 5 mA maximum at 5 V and 4 mA maximum at 3.3 V |
| Temperature compensation | The A versions counter the drift of a magnet, the Z versions do not |
| Field direction | Measured perpendicular to the top of the package, and the two bodies sense from different faces |
| Output range | The swing stops short of both rails, so the converter cannot use the full supply span |
| Propagation delay | Quoted from a change in flux to a change in the output, read it before closing a fast loop |
Family variants and how they differ
| DRV5055A1QDBZR | The 100 mV per mT member for a short travel and the highest resolution |
| DRV5055A3QDBZR | The 25 mV per mT member for a longer travel |
| DRV5055A4QDBZR | The 12.5 mV per mT member for the longest travel of the family |
| DRV5055A8QDBZR | 66 mV per mT over plus or minus 75 mT, a middle option with a wider range |
| DRV5055Z2QDBZR | The same 50 mV per mT member without magnet temperature compensation |
| DRV5053 | An earlier linear Hall family with a fixed sensitivity, for a board that cannot change its firmware |
| DRV5013 | A latching digital Hall sensor when only a position switch is needed rather than an analog reading |
Points to check before this part goes on a BOM
The 50 mV per millitesla figure is quoted at 5 V and shrinks with the supply. At 3.3 V the same part delivers about two thirds of the swing per millitesla, because the output is ratiometric and the sensitivity scales with the rail. A converter configured for the 5 V figure reads about a third low on a 3.3 V board.
The quiescent point sits at half the supply, not at a fixed voltage. A 5 V board puts it at 2.5 V and a 3.3 V board at 1.65 V, and the converter reference has to come from the same rail to cancel the error. Using an internal fixed reference throws away the ratiometric benefit and adds the supply tolerance straight into the reading.
The output stops short of both rails. The swing is limited by the output stage, so the usable range is smaller than the supply and a magnet that saturates the part produces a clamped reading that looks like a valid position. The travel and the air gap have to be chosen so the field stays inside the rated plus or minus 42 mT over the whole mechanical tolerance, not just at the nominal point.
The A suffix compensates for the magnet, not for the sensor. The internal compensation counters the temperature coefficient of a typical magnet so the reading stays proportional over minus 40 to plus 125 degrees. A magnet with a different coefficient, or a field that comes from a current carrying conductor rather than a permanent magnet, is outside what the compensation was built for and needs the Z version with software correction.
The two bodies do not sense the same face. The SOT-23 part senses perpendicular to the top of the package and the TO-92 part senses through its flat face, so a mechanical assembly drawn for one does not automatically work with the other. Changing the body late in a programme is a mechanical change, not just a part number change.
Position sensing with a magnet and a converter
A linear Hall sensor plus a permanent magnet is the cheapest absolute position sensor for travels of a few millimetres to a few centimetres. The magnet moves over the package, the field changes linearly with the distance, and the converter reads a voltage that maps to position. The 50 mV per mT member covers a plus or minus 42 mT window, which for a typical 6 mm diameter magnet is a travel of several millimetres with the field falling off with distance.
The ratiometric output is what makes that arrangement stable in a product that runs from a battery or a loosely regulated rail. When the converter uses the same supply as its reference, a rail drop moves both the signal and the reference together and the ratio, which is the position, stays put. That is the reason the sensor is specified as ratiometric rather than as an absolute voltage output.
Why the bandwidth matters for a current sensor
The same part can measure current by measuring the field a conductor produces, and there the 20 kHz bandwidth matters. A motor current loop closed at 2 to 5 kHz needs a sensor that does not add a pole inside the loop, and a Hall sensor with a 20 kHz front end keeps the phase margin where the controller expects it.
The trade is noise. A 20 kHz front end passes more of the sensor noise than a filtered one, and the output noise figures are quoted over that band. Systems that only need a slow position reading can add an RC filter at the converter input and get a quieter reading at the cost of bandwidth, which is a board level decision rather than a part change.
Where this order code fits
The part is used where a small magnet has to be read as an absolute position over a few millimetres of travel, or where a conductor field has to be read as a current. Teams comparing it with a neighbouring part start from our Medical Device Components page, and teams replacing a part that has gone end of life start from the Drone UAV Components page.
Questions buyers ask
Can this part run from 3.3 V? Yes, and the sensitivity drops with the rail because the output is ratiometric. The 50 mV per mT figure is a 5 V number, and the same part at 3.3 V delivers roughly two thirds of that. The firmware constants have to match the rail in use.
What is the difference between the A and Z versions? The A version compensates for the temperature drift of a permanent magnet inside the sensor. The Z version leaves the raw signal alone, which is what a system measuring a conductor field wants, because there is no magnet to compensate for.
Does the package direction matter? Yes. The field is sensed perpendicular to the top of the SOT-23 body and through the flat face of the TO-92 body, so the magnet has to be placed against the sensing face of the body that is actually fitted. A mechanical drawing made for one body does not transfer to the other.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.