Contact Us

TPS54336ADRCR

Brand: Texas Instruments
Texas Instruments TPS54336ADRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54336ADRCR — Power Management & Signal Chain | Superb Automation

TPS54336ADRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54336ADRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54336ADRCR: 4.5 V to 28 V, 3 A synchronous buck with adjustable soft start

TPS54336ADRCR is a synchronous buck converter with both FETs inside the package in a VSON body of 10 pins. It converts 4.5 V to 28 V down to a rail set by two resistors at 3 A, with a fixed 340 kHz switching frequency and a soft start set by one capacitor.

Order code and package

Order codeTPS54336ADRCR, DRC package, 3000 pieces on a large reel
BodyVSON, 3.00 mm by 3.00 mm, ten pins with a heat pad
Switch resistance128 mOhm high side and 84 mOhm low side
Frequency340 kHz fixed, the adjustable frequency member of the family is the TPS54335A
Reference0.8 V at 0.8 per cent, 1.5 per cent over temperature

Electrical parameters that decide the application

Input range4.5 V to 28 V
Output range0.8 V up to the input, 3 A continuous
ControlCurrent mode, monotonic start up into a pre-biased output
Light loadPulse skipping, which keeps efficiency up at a few milliamps
Current limitCycle by cycle on the high side FET, with a low side sourcing limit and a sinking limit
OverloadHiccup mode after the preset overcurrent time
Shutdown current2 uA with the enable pin low
ProtectionThermal shutdown and an overvoltage transition clamp

Family variants and how they differ

TPS54335ASame silicon with a 2 ms internal soft start and a 50 kHz to 1.5 MHz adjustable frequency
TPS54335-1ASame part in a DRC body with a narrower heat pad for more pin clearance
TPS54336AAdjustable soft start through the SS pin, fixed 340 kHz
SO PowerPAD bodyThe eight pin package version, larger than the 3 mm VSON
RT pinPresent on the 335A for frequency setting, not used as a frequency pin on this member

Points to check before this part goes on a BOM

The 340 kHz fixed frequency is the point of this member. A lower frequency means a larger inductor for the same ripple, and it means lower switching loss; 340 kHz with 4.7 uH on a 12 V to 3.3 V rail gives about 1.5 A of ripple at 3 A load, which is 50 per cent and about as much as a current mode loop wants to see.

Conduction loss at 3 A is 0.86 W split as 0.29 W in the high side FET at 25 per cent duty and 0.57 W in the low side FET. That is the price of 128 mOhm and 84 mOhm devices in a 3 mm body, and it is why the heat pad is not optional on a board that runs 3 A continuously at 28 V input.

The soft start capacitor is the difference between this part and the TPS54335A, and it matters when the output bank is large or the rail is sequenced. A 10 nF capacitor on SS gives a ramp in the tens of milliseconds, which keeps the inrush below the current limit and stops the hiccup circuit from tripping on a legal start.

Monotonic start up into a pre-biased output is a sequencing requirement, not a feature list item. When a 1.2 V rail is already held up by another converter, the part must not pull it down before it ramps, and a converter without this behaviour puts a negative glitch on a rail that is already powering logic.

Pulse skipping at light load raises the ripple and lowers the frequency, which is fine for a load that sleeps but wrong for an analog rail. A 3.3 V analog supply that feeds an ADC should stay in continuous conduction, and this part has no pin to force it, so the choice is made by the load current rather than by the board.

The current limit has three parts. The high side cycle by cycle limit stops the peak, the low side sourcing limit stops current runaway in a short, and the low side sinking limit turns the low side FET off to stop reverse current when the output is held above the regulation point. A rail that is back fed without the third one charges the input through the low side body diode.

The 4.5 V input floor with a 0.8 V reference means the part cannot make a 5 V rail from a 5 V bus. A 5 V rail at minus five per cent is 4.75 V, which is inside the input range but leaves 0.25 V of headroom for the high side FET and the inductor resistance at 3 A, so the part runs out of duty cycle before it runs out of current.

The 28 V input limit is the maximum operating value, and a 24 V bus at plus ten per cent is 26.4 V, which fits, while a 24 V bus with a load dump is not covered. Equipment that sees a vehicle bus needs the 42 V part, and this one is for a regulated 24 V rail inside a product.

The hiccup timer is set by the same components that set the loop, so a converter that is stable can still hiccup on a legal start if the output bank is large. The practical check is to start the board into its real load and watch the input current, not the output voltage: a start that trips the limit shows as a current stair step rather than a smooth ramp.

The 28 V input and 3 A output combination is the worst case for the package. At 28 V to 3.3 V the duty is 12 per cent and the low side FET carries 88 per cent of the current, so the 84 mOhm device dissipates 0.66 W while the high side dissipates 0.13 W. The heat pad is under the low side FET for a reason, and the copper it sits on is the thermal path.

The 0.8 V reference sets the divider current, not just the divider ratio. At 3.3 V out the bottom resistor carries 0.8 V and the top resistor the rest, so a 10 kOhm bottom resistor draws 80 uA and a 1 kOhm bottom resistor draws 800 uA. The lower value buys immunity to leakage and costs 2.6 mW at 3.3 V, which is the trade a standby rail has to make explicitly rather than by copying a divider from another board.

Where this order code fits

The part suits a set top box, a monitor, a router or an industrial controller that needs 3 A at 5 V, 3.3 V or 1.8 V from a 12 V or 24 V adapter rail, with a soft start set by the board rather than by the silicon. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What is the difference from the TPS54335A? The 335A has a 2 ms fixed soft start and an adjustable frequency from 50 kHz to 1.5 MHz. This member has an adjustable soft start and a fixed 340 kHz.

Does it need a bootstrap capacitor? Yes, one capacitor from BOOT to PH, and the part has no external diode.

Can the output be above the input? No. It is a buck converter, and the output has to stay below the input by the dropout of the high side FET and the inductor.

What happens on a shorted output? The high side limit holds the peak current, the hiccup timer runs, the part stops and restarts. The average current into a short is much lower than the limit.

How is the frequency set? It is fixed at 340 kHz. Boards that need another frequency use the TPS54335A, which has an RT pin and a 50 kHz to 1.5 MHz range.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.