Contact Us

TPS2561DRCR

Brand: Texas Instruments
Texas Instruments TPS2561DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2561DRCR — Power Management & Signal Chain | Superb Automation

TPS2561DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2561DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2561DRCR: dual channel adjustable limit switch in a 3 mm body

TPS2561DRCR is a two channel power switch with independent adjustable current limits in a VSON body of 10 pins. Each channel has its own enable, its own fault flag and a shared current limit resistor, in a three millimetre square body with a thermal pad.

Order code and package

Order codeTPS2561DRCR, DRC package, VSON ten lead with thermal pad
ChannelsTwo independent switches with separate enables and separate fault outputs
Limit programmingOne resistor from ILIM sets both channels, recommended 20 kOhm to 187 kOhm
EnableActive high on this member, the TPS2560 carries the active low version
Body3.00 mm by 3.00 mm, thermal pad connected to ground

Electrical parameters that decide the application

Limit at 20 kOhm2590 mA minimum, 2800 mA typical, 3005 mA maximum per channel
Limit at 61.9 kOhm800 mA minimum, 900 mA typical, 1005 mA maximum per channel
Limit at 100 kOhm470 mA minimum, 560 mA typical, 645 mA maximum per channel
Short circuit response3.5 us typical from the short to the current falling
Input range2.5 V to 6.5 V, covering a 3.3 V and a 5 V rail
FlagsOpen drain active low per channel, asserted on overcurrent or overtemperature
ThermalOvertemperature shutdown, with the pad as the heat path for both channels

Family variants and how they differ

TPS2560Same dual switch with active low enables
TPS2553Single channel of the same idea with a wider resistor range
TPS2052BTwo fixed 0.5 A channels when a resistor is not wanted
TPS2069CSingle channel fixed 1 A for a port that does not need adjustment
TPS22992Two channels is not offered there; that part is a single 6 A switch with a bias pin

Points to check before this part goes on a BOM

Two channels in one body share a limit resistor, which is the important constraint. A product with a 500 mA port and a 1.5 A port cannot use one TPS2561, because both channels would be set to the same threshold. The part is for two ports of the same class, such as two USB downstream ports, where one resistor sets both and the board area of a second device is saved.

The three published limit points at 20 kOhm, 61.9 kOhm and 100 kOhm show how the threshold scales: 2.8 A, 900 mA and 560 mA. The tolerance at each point is about plus or minus 7 percent at the typical, which is tighter than the fixed limit families and is the reason to pay for the resistor. A 500 mA port set at 61.9 kOhm sits at 800 mA minimum, so the load has 300 mA of headroom above its rating and the connector sees no more than 1005 mA.

The 3.5 us short circuit response is the number that keeps the upstream 5 V rail alive when one of the two ports shorts. Each channel limits independently, so a fault on channel one does not take channel two down, and the flag tells the host which one failed. That independence is the reason to use a dual switch rather than one device per port only when the two ports are the same class and the board area matters.

The thermal pad is shared by both channels and is connected to ground. With both channels at 1 A the dissipation is roughly twice the single channel figure, and the pad has to carry both. A land pattern that connects the pad to a small island under the body will run hotter than the datasheet figure, and a product that loads both ports continuously should be measured rather than calculated from one channel.

The input range of 2.5 V to 6.5 V covers the 3.3 V and 5 V rails with one order code, but the electrical table is written for a 5 V input. At 3.3 V the on resistance and the limit both shift, and the published minimum and maximum limits are specified at 5 V. A 3.3 V board needs the curves for that rail rather than the table, and the difference is large enough to change a connector rating.

The flag outputs are per channel and open drain, so two pull ups are needed and the host can distinguish the ports. A product that wires the two flags together saves a resistor and loses the information, which turns a two port fault into a single anonymous interrupt. The flags also assert on overtemperature, so a hot board can report a fault on a channel that has no load problem.

The ten lead VSON is 3 mm square, which is small for two switches that can pass 2.8 A each. The limit is the thermal path through the pad, not the silicon, and the datasheet thermal table gives the junction to ambient resistance for the package on the JEDEC board. At the top of the limit range with both channels loaded, the part depends on the copper and on the airflow, and a sealed enclosure changes both.

The fixed 20 kOhm to 187 kOhm resistor range is a stability constraint rather than a preference. Below 20 kOhm the limit rises towards 2.8 A and the loop has less margin, above 187 kOhm the offsets dominate and the accuracy falls away. The published points are inside that range, and a resistor chosen outside it produces a limit that is neither accurate nor stable, which shows up as a port that trips at a different current on different boards.

Both channels share one limit resistor, so the current budget of the two ports has to be the same before this part is chosen. A product with one 500 mA port and one 1.5 A port needs two single channel devices, and the board area saved by the dual part is not worth a limit that is wrong for one of the ports. The published points also show that the same resistor produces the same limit on both channels within the tolerance of the sense amplifiers, so a build that needs the two ports to be identical is served well, and a build that needs them different is not served at all. The two enables are separate, however, so the ports can still be switched on at different times, which is what a host needs when one port must stay off while the other enumerates. A shared fault flag would undo that advantage, so the two flag pins should stay on separate inputs.

Where this order code fits

It is the dual port switch for two downstream USB ports of the same class, or two identical peripheral bays, where the limit has to be tailored to the connector and the board area of a second device is not available. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Reduce Component Cost page.

Questions buyers ask

Can the two channels have different limits? No, one resistor sets both, so the part suits two ports of the same class.

What is the limit at 61.9 kOhm? 800 mA minimum, 900 mA typical, 1005 mA maximum per channel.

Does one channel fault affect the other? No, each channel limits and flags independently.

What is the difference from the TPS2560? The 2560 has active low enables; this order code has active high enables.

Can the two channels be paralleled for a higher current? No, each channel has its own sense loop and flag, and the limit resistor sets both to the same threshold rather than summing them.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.