Contact Us

TPS62872Z0WRXSR

Brand: Texas Instruments
Texas Instruments TPS62872Z0WRXSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62872Z0WRXSR — Power Management & Signal Chain | Superb Automation

TPS62872Z0WRXSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62872Z0WRXSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62872Z0WRXSR: 2.7 V to 6 V, 12 A synchronous buck with I2C in a 16 pin VQFN-FCRLF

TPS62872Z0WRXSR is a high current synchronous buck with a digital interface that sets the output voltage, the switching frequency and the soft-start time from a register map in a VQFN-FCRLF body of 16 pins. It feeds a core rail or a DDR rail where the voltage has to be trimmed in the field, and it senses the output at the load rather than at the converter, so the drop across the copper is corrected instead of being budgeted.

Order code and package

Order codeTPS62872Z0WRXSR, RXS package, VQFN-FCRLF, 16 pins, 3000 pieces on a large reel
Family positionTPS62870 at 6 A, TPS62871 at 9 A, TPS62872 at 12 A and TPS62873 at 15 A, all pin to pin in the same body
Variant selectionThe Z code sets the start-up voltage and the I2C address together, so the two cannot be chosen independently
This variant0.750 V start-up, I2C address 0x41, spread spectrum and soft-start defaults set by the option table
Voltage selectionThe VSEL pin picks one of four start-up voltages when the board has to boot at more than one setting
SensingVOSNS and GOSNS are differential remote sense inputs, not a local feedback tap

Electrical parameters that decide the application

Input range2.7 V to 6 V operating, with an over voltage lockout at 6.3 V rising and 6.2 V falling
Output current12 A continuous in the RXS body, the family covering 6 A, 9 A, 12 A and 15 A
Output range0.5 V to 1.4 V in the register map, set by the VSET field and the VRANGE field rather than by a divider
Switching frequency2.25 MHz, 2.5 MHz or 3 MHz selectable, each with a plus or minus 10 per cent window
Supply current40 uA operating with the device not switching, 16.5 uA in standby with the enable pin low
Under voltage lockout2.6 V rising and 2.5 V falling with 90 mV of hysteresis
Thermal limitsWarning at 150 C and shutdown at 170 C, each with 20 C of hysteresis
InterfaceI2C on SDA and SCL with the address fixed by the variant, and a MODE/SYNC pin for mode and clock
Soft startDefault 1 ms on this option, programmable through the SSTIME field, with new setpoints ignored until the ramp completes

Family variants and how they differ

TPS62873Z0WRXSRthe 15 A member with the same 0.800 V start-up and the same 0x40 address family, for a board that needs more current without a second body
TPS62872Z2WRXSRthe same 12 A die with a 0.875 V start-up and address 0x42, selected by the VSEL strap rather than by the I2C address
TPS62872Z4WRXSRthe 0.800 V start-up with address 0x43, which is the option to take when three of these sit on one bus
TPSM8287A12the same converter delivered as an integrated inductor module, for boards that cannot place an inductor and a compensation network
TPS62A01a 1 A buck in the same input range with a fixed 0.6 V reference, for the housekeeping rails around this one

Points to check before this part goes on a BOM

The start-up voltage and the I2C address are one choice, not two. The Z0 option starts at 0.750 V and answers at 0x41, the Z2 option starts at 0.875 V and answers at 0x42, the Z4 option starts at 0.800 V and answers at 0x43, and there is no variant that lets a board pick one without the other. A board that needs three of these on one bus has to take the three different addresses, which means three different start-up voltages, and the boot code has to program the rail to its working value before the load is released.

The VSEL pin is the escape hatch for that coupling. It selects which of four start-up voltages the device uses at power up, so one order code can boot at a low voltage and step to a higher one without touching the bus. The strap is read at start-up, and a board that changes it at run time gets no effect until the part is cycled, which is the kind of detail that shows up as a rail stuck at the wrong level after a warm reset.

The output is set in registers, so there is no divider to calculate and no feedback resistor tolerance to add to the error budget. That is the reason to buy this part rather than a fixed-output converter, and it is also the reason the boot sequence matters: until the controller writes the VSET field the rail sits at the option's start-up voltage, and a load that draws current at that level is running outside its own specification for however long the write takes.

Remote sense is the second reason. VOSNS and GOSNS are a differential pair that has to be routed as a pair to the load, and the converter corrects for the drop in the copper and the connector. On a 12 A rail at 0.9 V, 2 mOhm of board resistance is 24 mV, which is 2.7 per cent of the rail, and a local sense tap would give that away. The pair has to be routed away from the switch node, because the same 24 mV of noise on the sense lines appears as an error the loop tries to correct.

All three frequencies are specified against a 3.3 V input and a 0.75 V output, which is a 23 per cent duty. At 3 MHz the on time is 76 ns per cycle, and the minimum on time of the part plus the gate drive delays start to matter at the top of the input range. A 6 V to 0.5 V rail is 8 per cent duty and 27 ns at 3 MHz, which is inside the part but leaves little room for jitter, so the lower frequency settings exist for exactly that corner.

The supply current figures separate two states that a power budget usually conflates. The 40 uA line is the device operating but not switching, and the 16.5 uA line is standby with the enable pin low. Neither is the current at full load, and neither is a light-load efficiency claim: this part runs in forced PWM or in a power save mode set by the MODE/SYNC pin, and the mode decides whether the quiescent current is the dominant term at milliamps of load.

The two lockouts protect different ends of the input range. The under voltage lockout at 2.6 V rising and 2.5 V falling keeps the part from trying to regulate a 2.7 V rail that is still coming up, and the over voltage lockout at 6.3 V protects a rail that is specified to 6 V from a 5 V adapter that overshoots at plug in. Both are specified with their own hysteresis, 90 mV and 85 mV, so a rail that sits near either threshold does not chatter between run and stop.

The thermal warning at 150 C is a register flag that a controller can read before the 170 C shutdown arrives, and that is the only early warning the part gives. A 12 A rail in a 2.5 mm by 2.5 mm body has a thermal path that runs through the pad and the vias, so the difference between a board that holds 12 A and one that folds back at 8 A is usually the copper under the part rather than the converter. The 20 C of hysteresis on both thresholds means a part that has warned keeps the flag set until it cools well below the trip point.

Where this order code fits

It belongs on the core rail of an FPGA, an ASIC or a network processor, on a DDR supply where the termination voltage has to track, and on any board where the rail is trimmed at test rather than fixed by resistors. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is this the 12 A or the 15 A part? 12 A. The family runs 6 A, 9 A, 12 A and 15 A pin to pin, and the TPS62873 is the 15 A member in the same body.

Can the I2C address be changed? No. The address is fixed by the Z option and tied to the start-up voltage, so three parts on one bus need three different order codes.

What sets the output voltage? The VSET and VRANGE register fields. There is no external divider, and the rail sits at the option's start-up voltage until the controller writes the register.

Does it need an external clock? No. The MODE/SYNC pin can take a clock, but the part switches on its own at 2.25 MHz, 2.5 MHz or 3 MHz without one.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.