Contact Us

DRV10983PWPR

Brand: Texas Instruments
Texas Instruments DRV10983PWPR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV10983PWPR — Power Management & Signal Chain | Superb Automation

DRV10983PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV10983PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV10983PWPR: a sensorless three phase driver for fan motors

The DRV10983PWPR is a three phase brushless motor driver with the power FETs, the commutation logic and a step down regulator inside one 24 pin body. It drives up to 2 A continuous and 3 A peak winding current from an 8 to 28 V rail, with 250 mΩ of combined resistance, and it does so without Hall sensors: the control loop reads the back EMF of the rotating winding and synthesises a continuous sinusoidal drive from it. The result is a fan or pump that runs quietly, because the commutation steps that produce the pure tone noise of a block commutated drive are gone.

The interface is deliberately simple. Speed can be set by an analogue voltage, by a PWM duty cycle, or by an I2C register write, and the tachometer output on the FG pin reports the electrical frequency back to the controller. A small EEPROM inside the part stores the motor parameters and the spin up profile, so the same driver board can be tuned to a different motor without a code change on the host.

The DRV10983PWPR rows as the addendum publishes them

Part classThree phase sensorless BLDC driver with integrated FETs
Vendor statusACTIVE, production data
Data sheetSLVSCP6H, July 2014, revised June 2020
Operating voltage8 V to 28 V
Continuous winding current2 A
Peak winding current3 A
RDS(on), high and low combined250 mΩ typical, 400 mΩ maximum at 24 V and 1 A
RDS(on) at 85 degrees325 mΩ typical
Supply current, buck mode3.5 mA typical, 5 mA maximum
Supply current, linear mode11 mA typical
Standby current, buck mode3 mA typical, 4 mA maximum
Sleep current, Z variant160 µA typical, 200 µA maximum
Undervoltage lockout rise7.0 V minimum, 7.4 V typical, 8.0 V maximum
Undervoltage lockout fall6.7 V minimum, 7.1 V typical, 7.5 V maximum
Lockout hysteresis200 to 400 mV
Step down output5.0 V or 3.4 V, 100 mA maximum load
Linear regulator3.3 V at 5 mA, 1.78 V core rail
Overcurrent protection3 A minimum, 4 A at 25 degrees, phase to phase
Thermal shutdown150 degrees with 10 degrees hysteresis
Lock detection0.3 s to enter, 5 s to release
PWM input frequency1 kHz to 100 kHz
Analogue speed range100 mV zero, 0.9 V full scale, 5.8 mV resolution
BodyHTSSOP with PowerPAD, 24 pins, 7.80 by 6.40 millimetres
Reel rowDRV10983PWPR, 2000 pieces, large tape and reel, Active
Tube rowDRV10983PWP, 60 pieces, tube, Active
MarkingDRV10983, with DRV10983Z on the sleep variant
Moisture levelLevel 2 at 260 degrees, one year floor life

Two rows decide the variant. The plain DRV10983 keeps the regulator running in standby, drawing 3 mA, so an external microcontroller stays powered while the motor is stopped. The Z variant shuts the regulator down and draws 160 µA, which is what a battery powered or always on appliance needs, but the external controller then loses its rail. Mixing the two on one board produces a fan that works and a controller that resets, so the marking on the top of the package has to be read rather than assumed.

What sensorless commutation asks of the motor

The control loop needs to see the back EMF, and it cannot see it while the motor is stationary. The part therefore starts open loop, ramps the frequency and the current until the rotor is turning fast enough for the EMF to be measurable, and then hands over to closed loop. The EEPROM stores the ramp profile, and that profile is specific to the motor: a fan with a heavy impeller needs a longer ramp and more starting current than a bare rotor. A board that is moved from one fan model to another without retuning will start some units and stall others.

The second requirement is a minimum inductance and a known phase resistance. The tuning procedure measures both, and the values are written into the EEPROM registers. A motor with a very low inductance produces a noisy current waveform that the EMF observer struggles to separate from switching noise, which is why very small high speed fans are harder to drive than 120 millimetre chassis fans.

The regulator inside, and what it can power

The step down regulator takes the 24 V rail down to 5 V or 3.4 V and can deliver 100 mA, which is enough for a Hall sensor, an LED string or a small microcontroller. In linear mode it dissipates the difference as heat, so a 24 V to 3.3 V conversion at 50 mA would burn a watt inside a body that is already hot. The buck mode is the only sensible choice above 12 V, and that is why the supply current rows differ so much between the two modes.

The 3.3 V linear regulator is separate and only rated 5 mA, so it powers the internal logic and a light external load. Using it for anything larger is the second most common mistake on these boards, after mixing the standby and sleep variants.

Thermal behaviour in a fan housing

At 2 A the three phases conduct through two FETs at a time, so the loss is 250 mΩ times the square of the current, about 1 W at 25 degrees and 1.3 W at 85. The package pad is 6.4 millimetres wide and sits directly under the die, and the board it lands on is usually a small round PCB inside a motor housing with no airflow across it. The junction therefore runs hot, and the 150 degree shutdown is a real limit rather than a theoretical one.

Because the current is sinusoidal, the loss is spread across the cycle rather than concentrated at a commutation edge, which is an advantage over a block commutated drive at the same average current. That, plus the absence of the sixth harmonic torque ripple, is why the acoustic difference is audible even when the electrical difference is not.

Buying DRV10983PWPR

The 2000 piece reel and the 60 piece tube are both live, so a prototype can be built from a tube and a production run from a reel. The tube saves the buyer from opening a reel for fifty pieces, and the parts in it are level 2 by default because the tube is sealed. Both carriers carry the same marking, so the pack has to be identified from the label.

The Z variant is a separate orderable string with its own tube and reel rows. A customer who tunes a board with the plain part and then switches to Z to save standby power has to check that the external controller still has a rail, because the regulator stops in sleep.

Questions that arrive with this part number

Whether the part can run a motor without a tuning step is the first, and the honest answer is no: the EEPROM has to be loaded with the motor parameters, and that loading is a production step. The second is whether the I2C interface is required. It is not, because the analogue and PWM speed inputs work without any bus traffic, but the fault registers and the speed readback are only available over I2C.

The third is the difference between this part and a gate driver plus external FETs. The integrated part is smaller, cheaper in total and easier to certify for acoustic noise, and it cannot be scaled to a 10 A motor. Above 3 A peak the discrete route is the only one.

For a fan or pump programme that is moving from a Hall sensor drive, the lead time page covers the reel position, and the incoming inspection plan covers the marking check between the plain and Z variants.