CD4076BE
Product Specifications
CD4076BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4076BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4076BE: the four bit register with three state outputs in a 16-lead plastic DIP
The CD4076BE is the plastic dual in line entry for the CD4076B, a four bit register built from D-type flip-flops with three state outputs, in a 16-lead body. The vendor page lists the device as ACTIVE with four channels, a maximum clock of 8 MHz, a drive of 2.4 mA in both directions, a maximum supply current of 3000 microamps and an operating range of minus 55 to plus 125 degrees. The tube row is 25 pieces with a nickel palladium gold finish, and the marking is CD4076BE.
This is the one part in this group whose function is not a gate. Data enters four flip-flops on the clock edge, two data disable inputs decide whether the entry happens at all, and two output disable inputs put the four outputs into high impedance independently of the clock. That independence is the feature that matters on a bus, because a register that can only float its outputs by stopping the clock forces the whole timing chain to stop with it.
The CD4076B rows as the addendum publishes them
| Part class | Four bit D-type register, three state outputs |
| Vendor descriptor | 4-bit register, standard CMOS input, three state output |
| Vendor status | ACTIVE, catalogue rating |
| Data sheet | SCHS054 family document, acquired from Harris Semiconductor |
| Package addendum date | 18 September 2026 |
| Channels | Four flip-flops with common clock |
| Clock frequency | 8 MHz maximum in the parametric table |
| Output drive | 2.4 mA sink and source |
| Supply current | 3000 microamps maximum |
| Feature, power down | Partial power down support, Ioff |
| Feature, speed | Propagation between 10 and 50 ns in the page feature list |
| Input current | 1 microamp at 18 V over temperature, 100 nA at 25 degrees |
| Noise margin | 1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V |
| PDIP body | 16 leads, 181.42 square millimetres, 19.3 by 9.4 mm |
| PDIP rows | CD4076BE and CD4076BE.A, 25 pieces, Active |
| SOIC tube row | CD4076BM, 40 pieces, Active |
| SOIC small reel | CD4076BMT, 250 pieces, Active |
| SOIC large reel | Not published for this device |
| Ceramic rows | CD4076BF and CD4076BF3A, 25 pieces, Active |
| SOP and TSSOP | Not in the page package list and not in the addendum |
| Military rows | Ceramic F and F3A only, no separate drawing row |
The missing large reel is the surprise. Every other 14-lead device in this band sells a 2500 piece reel, and this 16-lead register stops at a 250 piece small reel. A line that places a thousand boards a month has to plan around five small reels per thousand units, and the changeover cost is real. The plastic DIP at 25 pieces is the other live format, so a customer who needs a thousand pieces surface mount is looking at four reels of 250, not one of 2500.
What the parametric table fixes
Eight megahertz is the maximum clock in the parametric table, and it is a limit on the flip-flops rather than on the outputs. The propagation window of 10 to 50 ns in the feature list is a range across supply and temperature, and the two figures together set the setup and hold budget: at 8 MHz a clock period is 125 ns, so a 50 ns propagation leaves 75 ns for the data path. A board that runs the register at 5 V and 8 MHz is inside the table, and a board that runs it at 3 V is outside the parametric ratings even though the product page says the family works from 3 V.
The supply current of 3000 microamps maximum is high for a CD4000B part and it is the price of the three state output stage. A quad gate in this family draws 150 microamps, so twenty times the current buys four flip-flops and a bus interface. A battery product that keeps the register powered for years should be told that number before the part is chosen, because the quiescent figure dominates the budget when the clock is stopped.
The three state outputs present a high impedance when either output disable input is high, and the vendor states that this happens independently of the clock. The data disable inputs work differently: they block the entry of new data without gating the clock, so the register holds its last value while the rest of the chain keeps running. Those two behaviours are often confused on a board review, and they are the two lines a test engineer should probe first.
Where the 16-lead body fits
The plastic DIP is 181.42 square millimetres and the SOIC is 59.4, so the surface mount body is a third of the area. The register has sixteen leads because four data inputs, four outputs, two data disables, two output disables, a clock and two rails do not fit in fourteen. A board that needs several registers can share the clock and the disable lines across packages, which keeps the bus width without adding control pins.
There is no TSSOP and no SOP row for this device, so the only surface mount body is the wide SOIC. That narrows the assembly choice: a line set up for 1.27 mm pitch can place it, and a line that only runs fine pitch parts has to add a feeder for this one package. The 40 piece tube is useful for a prototype and the 250 piece small reel is the volume format, and neither is a full production reel.
What the documents do not publish
The page gives no maximum clock at temperature, no setup and hold times, no output enable and disable times and no bus contention rating. Those are in the data sheet, and for a register they matter more than the gate delay, because a bus that turns on two drivers at once is a fault that no timing margin hides. The page also does not print the function table for the disable inputs, which is the first thing a software engineer asks for when the register is mapped into a bus.
The partial power down feature deserves a line of its own. The Ioff entry in the page feature list means the outputs stay high impedance when the rail is taken to zero, so a register on a bus that is powered down does not load the other drivers. That behaviour is not universal across the 4000 series, and a substitute that lacks it can pull a live bus low through its protection diodes. A customer who uses the register on a hot swap board should treat the feature as a requirement rather than a bonus.
The clock line is the other shared resource. Eight megahertz in the parametric table is a maximum for the flip-flops at the rated rails, and every register on the same clock adds input capacitance to that line. Four packages on one clock line is fine at 8 MHz, and eight packages may need a buffer. The page does not publish the input capacitance, so that sum has to come from the data sheet before the clock tree is fixed.
Second source and long term availability
The CD4076B is second sourced under the same number, and the nearest alternative in the 4000 family is the CD4076 with a different suffix rather than a different function. A move to a 74HC173 changes the pin out and the control polarity, so it is a board change rather than a substitution. The pin to pin cross reference page sets out the checks, and the component obsolescence management page covers what to do when only the small reel remains.
What to send with an enquiry
Send the string, the body, the quantity and the date. If the board is surface mount, confirm that 250 piece reels are acceptable, because there is no 2500 piece row for this device and the changeover plan has to be built around that. If the register sits on a shared bus, say how many drivers are on it, because the three state behaviour is the reason this part is chosen and the reason a substitute may not work. The BOM consolidation page explains how the pack sizes and the bus parts are grouped before a quote is issued.