Contact Us

CD4043BE

Brand: Texas Instruments
Texas Instruments CD4043BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4043BE — Power Management & Signal Chain | Superb Automation

CD4043BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4043BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4043BE: four NOR set-reset latches with three state outputs

CD4043BE is the through-hole member of the CD4043B family, four independent NOR set-reset latches with three state outputs in a 16-lead plastic DIP, 25 pieces to a tube. The vendor descriptor reads CMOS Quad NOR R/S Latch with 3-State Outputs, the document is the CD4043B and CD4044B data sheet revision D, and the parametric table gives four channels, standard CMOS inputs, three state outputs, 2.4 mA sink and source, partial power down support and a 16 Mbps data rate. The sibling CD4044B in the same document is the NAND version, which has active low set and reset rather than active high.

The addendum lists CD4043BE as Active in production, PDIP (N) with 16 leads, 25 pieces to a tube, RoHS yes with a nickel-palladium-gold finish, no moisture level for the through-hole body, minus 55 to plus 125 degrees, and the marking CD4043BE. The SOIC rows use the DR and DW suffixes rather than BM and BM96: CD4043BDR is Active at 2500 pieces, CD4043BDWR is Active at 2000 pieces and CD4043BDW is Obsolete, while CD4043BD and CD4043BDT are also obsolete.

The CD4043BE row as the vendor addendum publishes it

Part classQuad NOR set-reset latch with three state outputs
Vendor descriptorCMOS Quad NOR R/S Latch with 3-State Outputs
Vendor documentCD4043B and CD4044B data sheet revision D
ChannelsFour independent set-reset latches
Set and resetActive high NOR inputs
OutputsOne output per latch, three state, with a common output enable
Output drive, parametric table2.4 mA sink and source in the enabled state
Data rate, parametric table16 Mbps
Power down behaviourPartial power down supported
Supply range3 V to 18 V
Package for this codePDIP (N), 16 leads
Packing25 pieces in a tube
Lead finishNIPDAU
Moisture levelNot applicable for this package type
Operating rangeMinus 55 to plus 125 degrees
StatusActive, production
Part markingCD4043BE
SOIC reel rowCD4043BDR, 2500 pieces, marking CD4043BM
Wide SOIC reel rowCD4043BDWR, 2000 pieces
Obsolete rowsCD4043BD, CD4043BDT and CD4043BDW, quantity blank
Ceramic rowCD4043BF3A, 25 piece tube, tin lead finish

Four flags, one bus, and the enable that decides

A set-reset latch answers a different question from a flip-flop. It does not capture data on a clock; it holds a state that two events can change, and the state persists until one of the events happens again. Four latches in one package therefore hold four independent conditions, such as four fault flags or four door switches, and each one is set by its own event and cleared by its own reset line without any clock.

The three state output is what makes the part useful on a bus. A common output enable turns all four outputs on or off together, so four latches can share a four bit bus with other devices and only drive it when their enable is asserted. When the enable is low the outputs go to a high impedance state, which is what allows several such packages to sit on the same four lines.

The reset that is not a power-on reset

Both set and reset are active high, and a latch with both inputs high has both of its internal NOR paths pulling the output, which the data sheet defines as an invalid state. Releasing both inputs from that state leaves the latch in a state that depends on which falls first, which is a real source of intermittent behaviour on a board that drives both from one controller pin through an inverter.

The latch also has no defined state at power up. A board that needs all four flags clear when the supply comes up must assert the reset lines, either from a controller or from an RC network, and must hold them long enough for the supply to settle. The leakage of 1 microamp at 18 V over temperature sets how large the pull resistor can be on those lines: 100 k is safe, 1 megohm is not.

Drive, enable and the bus it shares

The enable has to be slower than the bus, not faster. A driver that turns on while another device is still driving the same lines puts two output stages in parallel for the length of the overlap, and the current that flows is set by the difference between the two output levels rather than by the load. A controller that sequences the enables with a few hundred nanoseconds between them avoids the overlap, and a board that ties all the enables to one line is relying on the parts being identical, which is not a rule that holds across a mixed bill of materials.

The output drive is 2.4 mA in the enabled state, which is enough for a short CMOS bus and for the inputs of several CMOS devices. It is not enough for a resistive bus or for a long trace, and the three state behaviour is only useful if the bus is short enough that the enabled driver can charge it within the read window. A board that puts four of these packages on one bus needs a check of the total capacitance rather than of the drive alone.

The partial power down support matters on a board with a standby rail: a latch that is powered down does not load the bus heavily, so the remaining devices can still drive it. That is a specified behaviour rather than a side effect, and it is one reason the part remains in equipment that has more than one supply.

Where the 4043 sits against the 4044 and the 4042

The CD4044B in the same document is the NAND latch, with active low set and reset, which suits a circuit where the events are active low signals from open collector or open drain sources. The CD4042B is the clocked D latch, which captures a data bus rather than holding two events, and it does not have three state outputs. The CD4013B is the edge triggered flip-flop for counting and division.

A board that holds four events takes the 4043B, a board whose events are active low takes the 4044B, a board that captures a bus takes the 4042B, and a board that counts takes the 4013B. All four are in the same family and the same 3 V to 18 V envelope, so the choice is about the event structure.

Incoming checks on a latch with three state outputs

Two checks are needed beyond the truth table. The first is the enable: with the enable low the output must float, and a part that still drives the bus will fight another driver, which is a fault that damages both parts rather than just one. The second is the invalid state recovery: both inputs high then released should leave the latch in one of the two valid states rather than oscillating. The body marking separates this DIP from the BDR and BDWR SOIC rows, whose suffixes differ from the gate family naming.

The reference pages are the incoming inspection plan, date code management, and the pin to pin cross reference when a legacy board needs a second source.

Questions that come up on the 4043

Whether the outputs can be tied together with another driver. They can, provided the enable is used, because the three state output exists for a shared bus and the enable is the only thing that keeps two drivers apart.

Whether the latch can be used as a debounce element. It can, and that is one of its oldest uses: a switch pulls set, another pulls reset, and the latch holds the last state without a clock.

Whether the part needs a clock. It does not, and the absence of a clock is the reason it is chosen for events that arrive at random times.

Whether the obsolete wide body row can still be bought. It appears with a blank quantity, so any stock is broker stock, and the active route is the DR or the DWR reel.