Contact Us

CD4001BM

Brand: Texas Instruments
Texas Instruments CD4001BM is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4001BM — Power Management & Signal Chain | Superb Automation

CD4001BM

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4001BM from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4001BM: the same four NOR gates in a 14-lead SOIC, 50 to a tube

CD4001BM is the small outline member of the CD4001B family: four independent 2-input NOR gates, buffered inputs and outputs, 3 V to 18 V, on the same die that the plastic DIP carries. The vendor document is SCHS015C revision C, shared with the CD4002B and the CD4025B, and the descriptor on the product page reads four channels, two inputs per channel, 3 V to 18 V. What separates this page from the DIP page is not the silicon but the body, the packing and the handling rules that follow from a surface mount part.

The addendum lists CD4001BM as Active in production, SOIC (D) with 14 leads, 50 pieces to a tube, RoHS yes with a nickel-palladium-gold finish, moisture sensitivity level 1 with a 260 degree peak and unlimited floor life, an operating range of minus 55 to plus 125 degrees, and the marking CD4001BM. Level 1 with unlimited floor life is the practical detail: the part does not need a dry cabinet, does not need to be counted against a floor life clock, and does not need a bake before reflow, which is what makes it usable on a line that opens a tube and runs it over several shifts.

The CD4001BM row as the vendor addendum publishes it

Part classQuad 2-input NOR gate, buffered inputs and outputs
Vendor descriptorFour channels, two inputs per channel, 3 V to 18 V
Vendor documentSCHS015C revision C, CD4001B, CD4002B and CD4025B
Supply range3 V to 18 V
Propagation delay, vendor figure60 ns typical at 10 V into a 50 pF load
Output drive, parametric table6.8 mA sink and source
Input current, maximum1 microamp at 18 V over the full range, 100 nA at 18 V and 25 degrees
Quiescent currentTested to maximum at 20 V on every unit
Noise margin1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V
Package for this codeSOIC (D), 14 leads
Body area, vendor figure51.9 square millimetres, 8.65 mm by 6 mm
Packing50 pieces in a tube
Lead finishNIPDAU
Moisture levelLevel 1, 260 degrees peak, unlimited floor life
Operating rangeMinus 55 to plus 125 degrees
StatusActive, production
Part markingCD4001BM
Reel member of the same bodyCD4001BM96, 2500 pieces on a large reel
Obsolete row of the same bodyCD4001BMT, quantity blank, Call TI
Through-hole memberCD4001BE, 14-lead PDIP, 25 piece tube
TSSOP memberCD4001BPWR, 2000 piece reel, marking CM001B

What four NOR gates do at 6.8 mA and 60 ns

The electrical envelope is the family envelope. Propagation delay is 60 ns typical at 10 V into 50 pF, drive is 6.8 mA in both directions, input current is 100 nA at 25 degrees and 1 microamp over temperature, noise margin is 1 V at 5 V, and the quiescent current is tested to maximum at 20 V on every unit rather than sampled. On a surface mount board the numbers that matter most are the two ends of that list: the 60 ns figure sets how many gate delays fit inside a timing window, and the leakage figure sets how large a pull resistor can be before the bias point drifts.

The 6.8 mA drive figure deserves a warning in the other direction as well. Four gates in one body means one package can drive four separate loads, and it is easy to total the current without checking the package dissipation. Each output at 6.8 mA into a 5 V rail dissipates about 34 mW if the output sits at half the rail, so four outputs loaded that way put about 136 mW into a 14-lead SOIC, which is inside the package limit but no longer negligible on a board that is already warm. The datasheet's own dissipation table is in the scanned section and this page does not quote a figure that it cannot read; the practical rule is to keep the four outputs below a few milliamps each unless the board has been checked thermally.

SOIC tube against SOIC reel: the 50 piece decision

The BM and the BM96 are the same body and the same die, and the only difference is packing: 50 pieces in a tube against 2500 on a large reel. A tube is the right format for a build of a few hundred boards, for a line that loads a feeder by hand, and for a service department that keeps a stock of the part for repairs. A reel is the right format for a production run that should not stop for a reload, and the reel also removes the tube handling that tends to bend leads on a 1.27 mm pitch body.

There is a cost side to the comparison that purchasing sees and engineering does not. A tube order splits into 50 piece multiples and leaves a partial tube at the end of a build, while a reel order is priced for a 2500 piece quantity and leaves a partial reel that has to be stored and tracked. For a first article run, the tube is the cheaper way to place the part on the line; for a repeat build with a stable forecast, the reel is the cheaper way to keep it there.

Where this body sits in the family and what replaces it

Inside the CD4001B family the bodies run PDIP, SOIC, TSSOP and the ceramic CDIP for the high reliability rows. The SOIC is the middle of that range: smaller than the DIP, easier to inspect than the TSSOP, and available on both a tube and a reel. The TSSOP member, CD4001BPWR, is 2000 to a reel with the marking CM001B, and it exists for boards where the 8.65 mm body of the SOIC does not fit. The ceramic CDIP rows, CD4001BF and CD4001BF3A, are the parts that carry the wide temperature grade and the military screening, and they are a different procurement conversation.

Across the logic family the substitutes are the CD4002B for a 4-input function and the CD4025B for a 3-input function, both in the same document, and the CD4011B when the function is NAND rather than NOR. A board that needs a mix of gate widths usually takes one of each rather than cascading 2-input gates, because each extra stage adds 60 ns and one more package to the bill.

Incoming checks for a surface mount logic line

A level 1 part still needs three checks. The body marking should read CD4001BM and not CD4001BMT, because the T row is obsolete and old stock circulates under a similar label. The date code should be inside the traceability window the customer requires, and the tube label should match the purchase order string including the reel or tube quantity. The third check is electrical: a 5 V truth table over the four gates plus a quiescent reading at 20 V covers both function and the screen the vendor applies.

The reference pages are the incoming inspection plan for the test sequence, date code management for the label rule, and the drop in replacement check when the SOIC is being considered against a different vendor's 4001.

Questions that come up on the SOIC body

Whether the BM and the BM96 can be mixed in one build. They can, since the die and the body are the same, but the packing has to be tracked separately because a partial reel and a partial tube do not combine cleanly on a feeder.

Whether the level 1 rating means no bake is ever needed. It means the part is not moisture sensitive at the stated peak temperature, so no bake is required for a normal reflow profile; a part that has been stored in a humid area for years should still be checked against the label rather than assumed.

Whether the part suits a 12 V automotive rail. The supply range allows 12 V and the temperature range covers minus 55 to plus 125 degrees, but the automotive qualification is a separate matter, and a circuit that needs an AEC part should look at the graded rows rather than at this catalogue code.

Whether the SOIC can be hand soldered for a prototype. It can, with a fine tip and drag soldering on a 1.27 mm pitch, and the level 1 rating means no pre bake is needed, which makes the tube a practical prototype format.