Contact Us

BQ76907RGRR

Brand: Texas Instruments
Texas Instruments BQ76907RGRR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ76907RGRR — Power Management & Signal Chain | Superb Automation

BQ76907RGRR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ76907RGRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ76907RGRR: a 2S to 7S monitor and protector in a 3.5 mm body

The BQ76907RGRR is a battery monitor and protector for packs from two to seven series cells. It carries the measurement, the protection comparators and the low side FET drivers in a 20 pin QFN that measures 3.5 mm on a side, which is small enough to sit on the same board as the cells in a hand held tool or a small vehicle battery.

The measurement chain is two converters. A 16 bit delta sigma converter reads the cells with a typical accuracy of 4 mV, and a separate 16 or 24 bit converter counts charge through the sense resistor with a plus or minus 200 mV input range. The charge count is accumulated into a 48 bit register with a time stamp, so the host can read coulomb count over long intervals without polling.

Protection covers voltage, temperature, current and the internal diagnostics, and the FET drivers are low side N channel with an option to recover on their own after a fault clears. The part talks I2C at up to 400 kHz with an optional CRC, and it provides a programmable regulator output for the host or for a small load.

Key data for the BQ76907RGRR

FunctionBattery monitor and protector for 2 to 7 series cells
ChemistriesLi-ion, lithium polymer, LiFePO4 and LTO
Voltage measurement16 bit delta sigma converter, 4 mV typical cell accuracy
Current measurementDedicated 16 or 24 bit coulomb counter, plus or minus 200 mV range
Charge accumulation48 bit accumulator with timer, read by the host at long intervals
ProtectionCell overvoltage and undervoltage, overcurrent in charge and discharge, overtemperature, internal diagnostics
FET driveLow side N channel charge and discharge drivers, optional autonomous recovery
BalancingHost controlled cell balancing
InterfaceI2C at 400 kHz, optional CRC, programmable regulator output
Current drawNORMAL 32 to 175 microamps, SLEEP 6 microamps, DEEPSLEEP 2.7 microamps
PackageVQFN, 20 pins, 3.5 mm body, marking SN
OrderingBQ76907RGRR, 3000 pieces on a large tape and reel, moisture level 1 with no floor life limit

The three power modes, and what each one is for

The difference between 175 microamps and 2.7 microamps is the difference between a pack that is flat after a month in a warehouse and one that is still usable after a year. The modes are set by the host and by the activity on the pack, and each one keeps a different set of functions alive.

In normal mode the part is measuring, protecting and talking on the bus. This is the state during charge and discharge, and the current in this mode moves across the published 32 to 175 microamp range depending on how much of the part is enabled and how often it converts. A pack that sits on a charger for a week is not in this mode most of the time.

Sleep mode keeps the protection comparators alive and turns off most of the measurement. A fault still opens the FETs, which is what a product needs while it sits idle on a shelf. Deep sleep turns off more, including parts of the protection path, and it is the state to use for shipping. Waking from deep sleep takes longer than waking from sleep, and a host that expects an immediate answer after a deep sleep wake will read a stale register.

Low side drive, and the ground it keeps

The charge and discharge FETs sit in the pack negative path, driven directly by the part. Low side drive means the gate signal is referenced to the pack negative, which is the same node the part sits on, so no charge pump is needed for the drive and the part can hold the FETs on with a rail that is derived from the pack itself.

The trade is that the pack negative is no longer a solid ground for the system. The FETs introduce a small resistance in the return path, and any load that shares that return sees a voltage that moves with the current. A host that measures its own supply against the pack negative has to account for that, or its readings will move with the load even when the pack is steady.

The autonomous recovery option decides what happens after a fault. With it enabled the part re closes the FETs after the condition clears and the delay expires, which is what a tool or a scooter wants. With it disabled the pack stays open until the host commands a recovery, which is what a pack that has to log the event before it resumes wants.

Where it fits in a build

Small packs with a real protection requirement and a small board: cordless tools, garden equipment, e-bike batteries, robot vacuum packs, portable medical devices, and any product where a 20 pin package is the difference between fitting the enclosure and not. A 10S pack or a pack that needs high side drive belongs in the larger members of the family.

The part is also a natural choice for a pack that is built in the hundreds rather than the millions, because the external component count is low and the configuration lives in the part rather than in a host processor. For a first build of such a pack, the NPI production launch checklist page covers the items we confirm before a line is released.

The sourcing side of this part is covered on the supplier onboarding checklist. For a first build in a new package, that page covers what a supplier has to show before the part enters a line.

Questions we get on this code

Does it need a host processor? It protects on its own, so a pack can be safe without a host. Reading the state of charge, setting thresholds and controlling balancing all need a host on the bus.

Can the same part build a 3S and a 7S pack? Yes, the cell count is a configuration item and the sense inputs cover the range. The thresholds and the balancing settings change with the cell count, so the two packs do not share a configuration.

Is the coulomb counter accurate enough to report state of charge by itself? It is accurate as a charge count, and the drift comes from the offset and from the sense resistor. Long intervals between full cycles let the error grow, so a host that wants a state of charge figure has to correct the count against a voltage reference point now and then.

What is the programmable regulator for? It powers a small external load, typically the host or a radio, from the pack. Its output voltage is a configuration item, and the current it can supply is limited, so it is not a substitute for a system rail.