Contact Us
  • Home
  • COMPONENTS
  • Current Sense Shunt Resistors for Power Measurement

Current Sense Shunt Resistors for Power Measurement

Metal strip and metal plate shunt resistors from 0.5 milliohm to 0.1 ohm and 0.1 W to 6 W, with tolerance, TCR and case size listed for each part number.
quote now

Product Specifications

Current sense shunt resistors for power measurement

Product Overview

A shunt resistor turns current into a voltage that an amplifier or a converter can measure. The value is chosen so the full scale current produces a usable drop, usually 10 mV to 100 mV, without wasting more power than the thermal budget of the board allows. Everything else follows from that choice: the case size needed to dissipate the heat, the tolerance that sets the gain error, and the temperature coefficient that sets how far the reading drifts as the board warms up.

The metal strip construction is what makes a low value practical. A solid alloy element welded between copper terminals gives 0.5 milliohm to 0.1 ohm with an element TCR below 20 ppm per C, inductance of 0.5 nH to 5 nH, and a thermal EMF below 3 uV per C on the Vishay WSL parts. A thick film part with the same value would drift with temperature and would add inductance to the loop.

Power rating is stated at a terminal or ambient temperature, not at room temperature with the part in free air. The values in the table are the 70 C ratings from the maker data sheets, and they fall as the terminal temperature rises toward 170 C. On a dense board the copper area under the part is part of the thermal path, which is why the same part is quoted at a lower current when it sits between two hot components.

Key Specifications

ParameterMetal strip, two terminalMetal plate, ERJ-M1WHigh power, CSS2H
Resistance range0.0005 ohm to 0.1 ohm by case0.005 ohm to 0.02 ohm0.0005 ohm and above
Power at 70 C0.1 W to 2 W by case1 W6 W
Temperature coefficient±75 to ±110 ppm/°C±100 ppm/°C±50 ppm/°C
Thermal EMFbelow 3 uV/°Clow, metal plate elementlow, metal element
Inductance0.5 nH to 5 nHbelow 1.0 nHlow, solid element
Case sizes0603, 0805, 1206, 2010, 2512, 281625122512
Sense connectiontwo terminal, Kelvin pads on the boardtwo terminaltwo terminal, wide terminal
Operating temperature-65 C to +170 C-55 C to +170 C-55 C to +170 C

Included Models and Order Codes

The parts below cover the values used on motor drives, battery packs, DC to DC converters and instrument front ends. Resistance, tolerance, power rating, TCR and case size are copied from the maker data sheet for each part number.

Part NumberResistanceTolerancePowerTCRSizeTerminals
WSL0603R0100FEA0.01 ohm±1%0.1 W±110 ppm/°C06032
WSL0805R0100FEA0.01 ohm±1%0.125 W±110 ppm/°C08052
WSL1206R0100FEA0.01 ohm±1%0.25 W±110 ppm/°C12062
WSL1206R0500FEA0.05 ohm±1%0.25 W±75 ppm/°C12062
WSL2010R0100FEA0.01 ohm±1%0.5 W±110 ppm/°C20102
WSL2010R1000FEA0.1 ohm±1%0.5 W±75 ppm/°C20102
WSL2512R0100FEA0.01 ohm±1%1 W±110 ppm/°C25122
WSL2816R0150FEH0.015 ohm±1%2 W±110 ppm/°C28162
ERJ-M1WSF5M0U0.005 ohm±1%1 W±100 ppm/°C25122
CSS2H-2512R-L500F0.0005 ohm±1%6 W±50 ppm/°C25122

Key Features

Value sets the loss – a 10 milliohm shunt carrying 10 A drops 100 mV and dissipates 1 W, so the case size is set by the loss long before it is set by the resistance value.

TCR drives the gain drift – at 37 ppm per C a 0.005 ohm part moves 0.02 % of its value over a 50 C rise, which is small next to a 1 % tolerance, but at the milliohm values used on battery packs the same drift is a visible offset in the current reading.

Kelvin sensing removes the solder joint – on the two terminal parts the sense traces are taken from the inner edge of the pad, so the resistance of the joint and of the copper pour does not appear in the measurement.

Low thermal EMF for small signals – the metal strip element is below 3 uV per C against copper, so a 10 mV full scale signal is not buried under a thermocouple effect at the sense pads.

Inductance below 5 nH – a solid element has little inductance compared with a wound or thick film part, which keeps the shunt usable in a 100 kHz to 1 MHz current loop without a separate filter.

Power derating is part of the rating – the 1 W or 6 W figure is quoted at 70 C, and the part is derated toward 170 C. Where the shunt sits near a switching device, the figure we quote is the one at the actual terminal temperature.

Automotive qualified options – the metal strip and metal plate families on this page carry AEC-Q200 qualification in the cases listed, which is the requirement behind most battery and motor drive enquiries.

Applications

These parts are quoted for boards that measure current in a power path, typically where: The shunt is placed on the power path of the same board that carries the control circuit, so it is quoted together with the SUPERB PCB and the SUPERB PCBA build for that board.

Motor drive phase current – a 0.5 milliohm part in a 2512 case carries the phase current of a drive at 20 A to 40 A with a 6 W rating, and the low inductance keeps the measurement usable inside the switching loop.

Battery pack and BMS – a 1 milliohm to 5 milliohm part on the pack negative or positive terminal measures charge and discharge current, and the tolerance of the shunt becomes the gain error of the whole gauge.

DC to DC and hot swap – a 10 milliohm part on a 5 A rail gives 50 mV of signal for a current limit comparator, and the 0603 and 0805 cases keep the part inside the footprint of a dense converter.

Sourcing and Cross-Reference

Shunts are specified by value, tolerance, TCR and case size, and a substitute that matches only the first two will still change the reading on the board. A 1 % part with 110 ppm per C is not a substitute for a 1 % part with 50 ppm per C on a battery gauge, even when both are 2512 and both are 5 milliohm.

Our check starts from the full scale current and the allowed drop, then matches the power at the terminal temperature of the enclosure, the tolerance and the TCR. Where the original part has gone end of life, as the Panasonic ERJ-M1W series has, the replacement is chosen on the same four fields and the land pattern is compared before it is quoted, because the terminal width on a 2512 metal plate part is not the same as on a metal strip part of the same case.

The pairing of a shunt with its amplifier is where most of the error appears, and the cross reference route for that pair is on our power management cross reference page. Where a value or a case has to change, the rules we apply are on pin to pin cross reference.

For volume builds, SUPERB Assembly support covers the sense trace routing at the pads, the copper area under the part and the reflow profile the 2512 and 2816 cases need.

Q: Can you supply a shunt that matches the TCR and the power rating of a part that has gone end of life?

A: Yes. Send the resistance, tolerance, TCR, power rating and case size, plus the full scale current and the ambient temperature, and the SUPERB Tech team will confirm a part on all five fields before quoting.

Why Buyers Source Shunt Resistors Through SUPERB

  1. TCR matched, not ignored: a replacement is quoted at the same or a lower TCR, because the drift of the shunt becomes the drift of the current reading.
  2. Power at the real temperature: the rating is quoted at the terminal temperature the board will see, with the derating curve, rather than the headline figure at 70 C.
  3. Sense layout stated: the note on where the sense traces leave the pad goes out with the part, which is the difference between a 1 % reading and a 5 % reading on a two terminal shunt.
  4. End of life parts covered: values that the maker has dropped are sourced from stock and from equivalent families, with the case and the terminal width confirmed against the board.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Passive components, Current sense amplifiers and shunt monitors, Battery chargers and fuel gauges, Common mode chokes and power inductors, Power management cross reference.