Contact Us
  • Home
  • COMPONENTS
  • Peristaltic Pump Tubing and Pump Heads for Analysers

Peristaltic Pump Tubing and Pump Heads for Analysers

Peristaltic tubing is a wear part and a metering element at the same time. The bore sets the volume per revolution, the wall sets how well the rollers close the tube, and the material sets the pressure and the chemical range. This page covers bore sizes from 0.5 to 9.6 mm, six tube materials and the head families that take them, with flow per revolution for the colour-coded panel tubing. Every flow figure is the maker rating for that bore at a stated speed, so a pump can be sized without a trial run. Where a tube is replaced on a running analyser, the wall thickness and the head gap matter as much as the bore, because a thicker wall in the same head changes the occlusion.
quote now

Product Specifications

Product Overview

A peristaltic pump moves liquid by squeezing a tube, so the tube is both the wetted path and the measuring chamber. That is why a tube change can shift a calibration: the same nominal bore from two makers can differ in wall thickness by a tenth of a millimetre, and a thicker wall in the same head reduces the occlusion and the volume per revolution. On a reagent line that dispenses 50 microlitres per cycle, that difference shows up as a bias long before it shows up as a leak.

Bore is the first number to fix. Volume per revolution rises with the square of the bore, so a step from 1.6 to 3.2 mm is not twice the flow but roughly four times, and a step from 3.2 to 4.8 mm is a little over twice. The published figures for one family run 0.004 to 9.0 mL/min at 0.5 mm across 0.1 to 220 rpm, 0.04 to 92 mL/min at 1.6 mm, 0.17 to 370 mL/min at 3.2 mm, and 0.38 to 830 mL/min at 4.8 mm. Those ranges are the ones to use when a pump is selected, because a tube chosen on bore alone can be correct at one speed and outside the head rating at another.

Wall thickness is the second number. A 1.6 mm wall is the common rating for laboratory and analyser heads, and the same bore in a 1.0 mm wall is used on panel mount heads where the tube is held in a fixed channel. The two are not interchangeable: a thin wall tube in a head cut for a thick wall will not occlude, and a thick wall tube in a narrow channel will creep and shorten its life. When a tube is ordered as a replacement, the wall and the head gap are confirmed together, not just the bore.

Material closes the choice. Thermoplastic elastomer tube such as Bioprene gives a long squeeze life and low permeability and runs 5 to 80 C. Platinum-cured silicone gives the smoothest bore and the most stable flow, and runs -20 to 80 C, which is why it is the default for reagent and sample lines that are cleaned in place. Marprene is the choice for oxidising reagents and carries 7 bar (100 psi). Reinforced silicone such as STA-PURE PCS holds 100 psi and stays flexible to -20 C. Neoprene is the low cost option for water and mild chemistry. For a line that runs 24 hours a day, tube life is the cost driver, and the material choice matters more than the pump speed.

Key Specifications

ParameterValueNote
Bore range0.5 to 9.6 mm, which is 0.02 to 0.38 in0.5, 0.8, 1.6, 3.2, 4.8, 6.4 and 8.0 mm are the stocked steps
Wall thickness1.6 mm on the 913, 933, 941, 960, 965, 902 and 920 families; 1.0 mm on the panel mount familywall and head gap are confirmed together
Flow at 220 rpm, 0.5 mm bore0.004 to 9.0 mL/min across 0.1 to 220 rpmmaker rating for Marprene, Bioprene and PureWeld XL
Flow at 220 rpm, 1.6 mm bore0.04 to 92 mL/min across 0.1 to 220 rpmabout ten times the 0.5 mm bore at the same speed
Flow at 220 rpm, 3.2 mm bore0.17 to 370 mL/min across 0.1 to 220 rpmthe common step for reagent and sample lines
Flow at 220 rpm, 4.8 mm bore0.38 to 830 mL/min across 0.1 to 220 rpmused where a transfer step has to finish in seconds
Volume per revolution, panel tubing0.085 mL/rev at 1.14 mm bore, 0.34 mL/rev at 2.79 mm borecolour coded, ten bores from 1.14 to 2.79 mm
Pressure, Marprene7 bar, which is 100 psithe highest rating in the thermoplastic group
Pressure, STA-PURE PCS100 psireinforced silicone, flexible to -20 C
Temperature, Bioprene and Marprene5 to 80 C23 to 176 F
Temperature, Pumpsil and STA-PURE-20 to 80 C-4 to 176 F
MaterialsBioprene, Pumpsil platinum-cured silicone, PureWeld XL, STA-PURE PCS, STA-PURE PFL, Marprene, Neoprenesix families cover the analyser range
Head families114 head with seven tube sizes to 300 mL/min, 300 series heads, 520R head for 0.5 to 9.6 mmthe 520R covers the full bore range of the 500 series
Tube formatcontinuous coils and tube elementselements are cut to the head length and fitted with the same wall

Included Models and Order Codes

Part numbers below are the maker codes for a 1.6 mm wall tube, which is the standard element for a laboratory or analyser head. The suffix 016 is the wall in millimetres, so the same family in another wall carries a different suffix and is not a drop-in replacement. Flow is quoted at the top speed of the 500 series, 220 rpm, for the bore in that row.

PartMaterialBore and wallFlow at 220 rpmTemperatureNote
913.A005.016Pumpsil, platinum-cured silicone0.5 mm, 1.6 mm wall9.0 mL/min-20 to 80 Csmoothest bore, lowest flow in the family
913.A008.016Pumpsil0.8 mm, 1.6 mm wallnot stated for this bore-20 to 80 Cbetween the 0.5 and 1.6 mm steps
913.A016.016Pumpsil1.6 mm, 1.6 mm wall92 mL/min-20 to 80 Cthe default reagent line element
913.A032.016Pumpsil3.2 mm, 1.6 mm wall370 mL/min-20 to 80 Csample and wash lines
913.A048.016Pumpsil4.8 mm, 1.6 mm wall830 mL/min-20 to 80 Ctransfer and drain steps
913.A064.016Pumpsil6.4 mm, 1.6 mm wallnot stated for this bore-20 to 80 Clarger head, lower speed
913.A080.016Pumpsil8.0 mm, 1.6 mm wallnot stated for this bore-20 to 80 Chighest bore in the 500 series
933.0005.016Bioprene, thermoplastic elastomer0.5 mm, 1.6 mm wall9.0 mL/min5 to 80 Clong squeeze life, low permeability
933.0032.016Bioprene3.2 mm, 1.6 mm wall370 mL/min5 to 80 Csame flow as Pumpsil at this bore
941.0016.016PureWeld XL1.6 mm, 1.6 mm wall92 mL/minas Pumpsilwelded flow path for disposable assemblies
960.0016.016STA-PURE PCS, reinforced silicone1.6 mm, 1.6 mm wall92 mL/min-20 to 80 C100 psi rating
965.0032.016STA-PURE PFL3.2 mm, 1.6 mm wall370 mL/min-20 to 80 Creinforced, for higher pressure lines
902.0016.016Marprene, thermoplastic elastomer1.6 mm, 1.6 mm wall92 mL/min5 to 80 C7 bar rating, oxidising reagents
920.0032.016Neoprene3.2 mm, 1.6 mm wall370 mL/min5 to 80 Cwater and mild chemistry
049.EF6D.N05Bioprene, panel mount0.5 mm bore, 1.0 mm wallnot stated for this family5 to 80 Cfixed channel head, not for a 520R
049.EH6D.N10Silicone, panel mount1.0 mm bore, 1.0 mm wallnot stated for this family-20 to 80 Cthe same channel as the 0.5 mm tube
049.EF6D.N20Bioprene, panel mount2.0 mm bore, 1.0 mm wallnot stated for this family5 to 80 Cbetween the 1.0 and 3.0 mm steps
049.EH6D.N30Silicone, panel mount3.0 mm bore, 1.0 mm wallnot stated for this family-20 to 80 Clargest bore in this family

Colour Coded Panel Tubing, Volume per Revolution

Panel mount tubing is matched to a fixed channel rather than to a roller head, and it is identified by colour rather than by bore. The table gives the bore, the volume per revolution and the flow at four common speeds, which is the form used when a dispense volume is set in software.

Colour codeBoremL/rev12 rpm25 rpm60 rpm100 rpm
Red/Red1.14 mm0.0851.0 mL/min2.1 mL/min5.1 mL/min8.5 mL/min
Grey/Grey1.30 mm0.111.3 mL/min2.8 mL/min6.6 mL/min11 mL/min
Yellow/Yellow1.42 mm0.131.6 mL/min3.3 mL/min7.8 mL/min13 mL/min
Yellow/Blue1.52 mm0.141.7 mL/min3.5 mL/min8.4 mL/min14 mL/min
Blue/Blue1.65 mm0.172.0 mL/min4.3 mL/min10.2 mL/min17 mL/min
Green/Green1.85 mm0.202.4 mL/min5.0 mL/min12.0 mL/min20 mL/min
Purple/Purple2.06 mm0.242.9 mL/min6.0 mL/min14.4 mL/min24 mL/min
Purple/Black2.29 mm0.273.2 mL/min6.8 mL/min16.2 mL/min27 mL/min
Purple/Orange2.54 mm0.313.7 mL/min7.8 mL/min18.6 mL/min31 mL/min
Purple/White2.79 mm0.344.1 mL/min8.5 mL/min20.4 mL/min34 mL/min

Key Features

Bore range 0.5 to 9.6 mm – eight stocked steps cover a 1 microlitre per revolution line and a 9 litre per hour transfer line from the same head family

Wall thickness stated with the bore – the 016 suffix is 1.6 mm and the panel family is 1.0 mm, so a replacement is not ordered on bore alone

Six materials on one list – Bioprene, Pumpsil, PureWeld XL, two STA-PURE grades, Marprene and Neoprene, with the temperature and pressure of each

Platinum-cured silicone bore – the smooth bore gives a stable volume per revolution, which is what a reagent dispense is calibrated against

Marprene to 7 bar – 100 psi covers a pressurised reagent line without a reinforced tube

Reinforced silicone to 100 psi – STA-PURE PCS stays flexible to -20 C, for a line that is chilled or cleaned in place

Colour coded panel tubing – ten bores from 1.14 to 2.79 mm with volume per revolution, so a dispense volume is set without a calibration run

Head matching in the table – the 114 head to 300 mL/min, the 300 series heads and the 520R head for the full 0.5 to 9.6 mm range are named next to the tube

Applications

Peristaltic tubing appears wherever a liquid has to be moved without touching the pump. The three cases below set the material and the wall.

Clinical chemistry reagent lines – a reagent pack is pierced once and dispensed for a week. Pumpsil in 1.6 mm bore at a 1.6 mm wall gives the stable volume per revolution that a 50 microlitre dispense needs, and the smooth bore resists the protein film that builds on a rougher tube.

Water and process analysers – sample is drawn from a sample pot that carries grit and algae. A 3.2 mm bore in Marprene carries the flow at 7 bar without a reinforced wall, and the tube is changed on a schedule rather than on a failure, because a worn tube changes the sample volume before it splits.

Benchtop and panel mount instruments – a compact analyser uses a fixed channel head and colour coded tubing. The 1.14 mm red tube at 0.085 mL/rev allows a 100 microlitre dispense in about 1.2 revolutions, which is the smallest dispense that stays repeatable without a syringe pump.

The analyser boards that drive these pumps are the kind of build SUPERB PCB and SUPERB PCBA programmes cover, from the motor drive to the fluidic control stage.

Sourcing and Cross-Reference

Tubing is bought by bore, wall and material, and the wall is the field that gets dropped. A 3.2 mm bore in a 1.6 mm wall and the same bore in a 1.0 mm wall carry different part numbers and are not interchangeable, so the head and the channel are confirmed before a part is named. Where the old tube is still on the pump, the wall is measured rather than read from a catalogue.

Where a maker has retired a tube grade, the substitute is chosen on pressure and temperature first and on bore second. A silicone tube can replace a thermoplastic one on a reagent line, but it will not hold the same pressure at 80 C, and a line that runs near the pump limit will show the difference as a slow delivery rather than as a leak.

Tube life is the hidden cost. A line that runs 24 hours a day can consume a tube a month, and the decision between a low cost Neoprene tube and a longer life Bioprene tube is a cost per litre question. We quote both and let the maintenance interval decide, rather than defaulting to the cheapest part.

When a line is rebuilt, the tube, the head and the fittings are picked as one set, which is how SUPERB Assembly ships a pump overhaul.

Q: Can you supply the same bore in a different wall thickness when the original tube is no longer listed?

A: SUPERB Tech can confirm the bore, the wall and the head gap against the old tube before the order is placed.

Why Buy Peristaltic Tubing from SUPERB

  1. Wall thickness confirmed, not assumed: the head gap and the wall are checked together, because the same bore in two walls gives two different dispense volumes
  2. Flow per revolution on the panel family: a dispense volume is set from a published figure rather than from a trial and error calibration
  3. Six materials with pressure and temperature: the choice between silicone, thermoplastic and reinforced tube is made on the line conditions, not on availability
  4. Head families named in the table: the tube and the head are quoted as a pair, which is what avoids a tube that fits the pump but not the channel
  5. Maker code on the delivery file: the part number and the wall are both written down, so the next replacement is the same part

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Peristaltic and Diaphragm Micro Pumps for Analysers, Inline Degassing Modules and Vacuum Degassers for Liquid Lines, Quick Disconnect Couplings and Luer Fittings for Reagent Lines, Inline Filters and Frits for Reagent Lines, Gas Mass Flow Sensors for Ventilators and Analysers, Component Lead Time Solutions.

Actual product photos available on request