Holding Magnets and Magnetic Catches for Doors
Product Specifications
Product Overview
A magnetic catch closes a door with a magnet and a steel plate. There is no pawl, no spring and no moving part, which is why the part tolerates a frame that is welded slightly out of square and a door that has warped by a millimetre. The magnet pulls the door in, the plate gives it something to pull against, and the door is opened by pulling harder than the rated load.
The rating on the data sheet is the pull needed to separate the catch from its plate, measured on a straight pull. It is not the force the door sees in service: a door that is pulled at the handle, 200 mm from the catch, converts a 40 N rating into a smaller force at the magnet. That is why a large door takes a bigger catch than its mass alone suggests, and why two catches on a wide door are usually better than one heavy one.
The Southco 02 range on this page is the snap in family, in polypropylene, in black or white. The rectangular hole bodies run from 40 N on the medium size, 02-10-101-10, to 52 N on the large size, 02-10-201-10, and 105 N on the double magnet body, 02-10-801-10. The round hole bodies run from 24 N on the small size, 02-20-411-10, to 58 N on the large size, 02-20-612-10. The adhesive mount body, 02-30-121-10, is rated 40 N and is the one to use where the frame cannot be punched.
Mounting is the part that decides the installation. A snap in body needs a rectangular or a round hole with the right edge, and it is pressed in from the front, which means the hole is punched before the panel is painted. An adhesive body is stuck to a clean, flat surface and needs 24 hours before it is loaded. Neither is a screw fixing, so a frame that is expected to be adjusted needs a different family rather than a bigger screw.
The plate is part of the joint. A steel door closes against the magnet and the catch needs no plate, but a stainless door, an aluminium door or a plastic door does not attract a magnet in a useful way, and a steel strike plate has to be fitted to the door. The plate is thinner than the door and has to be recessed or surface mounted, and its thickness changes the gap, which changes the pull.
The second family on this page is the bare magnet, and it is the part for a custom door where a standard catch does not fit. The neodymium discs listed are N52 grade with a nickel copper nickel plating, from 3.18 mm diameter and 3.18 mm thick at 0.84 lb of pull up to 15.88 mm diameter and 6.35 mm thick at 18.94 lb. The pull figure is measured against a thick steel plate, which is the best case: a thin plate or a painted surface gives less.
Temperature is the limit to watch with a bare magnet. The N52 discs are rated to 80 C maximum operating temperature, and above that they lose strength permanently rather than temporarily. A cabinet that is powder coated at 180 C with the magnets already fitted is a cabinet with weak magnets, which is why they are fitted after the oven and not before.
A magnet is also a part that has to be treated with care on an assembly line. Two discs that snap together can chip their plating, and a chipped plating on a neodymium magnet is the start of corrosion. They are kept apart in the store, handled with a plastic spatula rather than a steel one, and kept away from a pacemaker, a watch and a magnetic stripe card.
Key Specifications
| Parameter | Value | Notes |
|---|---|---|
| Catch body material | Polypropylene | Black or white |
| Rated pull, rectangular hole | 40 N to 105 N | Medium, large and double magnet bodies |
| Rated pull, round hole | 24 N to 58 N | Small and large bodies |
| Rated pull, adhesive mount | 40 N | Where the frame cannot be punched |
| Installation | Snap in or adhesive mount | Snap in pressed from the front |
| Strike plate | Steel plate required on a non steel door | Plate thickness changes the gap |
| Magnet grade | N52 neodymium on the disc range | Nickel copper nickel plated |
| Magnet pull | 0.84 lb to 18.94 lb | Against a thick steel plate |
| Magnet maximum temperature | 80 C | Permanent loss above the rating |
| Magnet tolerance | Plus or minus 0.004 in | Per the supplier data |
| Magnet diameter range | 3.18 mm to 15.88 mm | Thickness 3.18 mm to 6.35 mm |
Included Models and Order Codes
The catches are listed by hole shape and rated pull, because the punching decides the part as much as the rating does. The bare magnets follow, with diameter, thickness and pull, for a door that has no room for a standard catch.
| Part Number | Type | Hole or Mounting | Rated Pull | Size | Colour |
|---|---|---|---|---|---|
| 02-10-101-10 | Magnetic catch latch | Rectangular hole, snap in | 40 N (8.7 lb) | Medium | Black |
| 02-10-101-20 | Magnetic catch latch | Rectangular hole, snap in | 40 N (8.7 lb) | Medium | White |
| 02-10-201-10 | Magnetic catch latch | Rectangular hole, snap in | 52 N (11.8 lb) | Large | Black |
| 02-10-201-20 | Magnetic catch latch | Rectangular hole, snap in | 52 N (11.8 lb) | Large | White |
| 02-10-801-10 | Magnetic catch, double magnet | Rectangular hole, snap in | 105 N (23 lb) | Large | Black |
| 02-20-411-10 | Magnetic catch latch | Round hole, snap in | 24 N (5.5 lb) | Small | Black |
| 02-20-612-10 | Magnetic catch latch | Round hole, snap in | 58 N (13 lb) | Large | Black |
| 02-30-121-10 | Magnetic catch latch | Adhesive mount | 40 N (8.7 lb) | Medium | Natural |
| D22-N52 | Neodymium disc | Pressed or bonded | 0.84 lb | 3.18 x 3.18 mm | Nickel plated |
| D24-N52 | Neodymium disc | Pressed or bonded | 1.05 lb | 3.18 x 6.35 mm | Nickel plated |
| D32-N52 | Neodymium disc | Pressed or bonded | 1.70 lb | 4.76 x 3.18 mm | Nickel plated |
| D34-N52 | Neodymium disc | Pressed or bonded | 2.44 lb | 4.76 x 6.35 mm | Nickel plated |
| D52-N52 | Neodymium disc | Pressed or bonded | 4.15 lb | 7.94 x 3.18 mm | Nickel plated |
| D54-N52 | Neodymium disc | Pressed or bonded | 6.32 lb | 7.94 x 6.35 mm | Nickel plated |
| D82-N52 | Neodymium disc | Pressed or bonded | 7.97 lb | 12.70 x 3.17 mm | Nickel plated |
| D84-N52 | Neodymium disc | Pressed or bonded | 13.47 lb | 12.70 x 6.35 mm | Nickel plated |
| DA2-N52 | Neodymium disc | Pressed or bonded | 10.15 lb | 15.88 x 3.18 mm | Nickel plated |
| DA4-N52 | Neodymium disc | Pressed or bonded | 18.94 lb | 15.88 x 6.35 mm | Nickel plated |
Key Features
No moving parts – A magnetic catch has nothing to wear, which is why it tolerates a warped door and a frame that is a millimetre out of square.
Rated pull stated in newtons and pounds – 24 N to 105 N on the catches, so the door mass can be checked against a number rather than a size class.
Two hole shapes – Rectangular and round snap in bodies, because the punching on the frame is usually already made when the catch is specified.
Adhesive body for an unpunched frame – 02-30-121-10 sticks to a flat surface at 40 N, for a retrofit where the panel cannot be cut.
Strike plate called out – A non steel door needs a steel plate, and the plate thickness changes the gap and the pull.
Bare magnets to 18.94 lb – N52 discs from 3.18 mm to 15.88 mm diameter, for a door that has no room for a standard catch.
Temperature limit on the magnet – 80 C maximum on the N52 discs, so the part is fitted after a powder coat bake rather than before.
Applications
These parts hold cabinet doors, access lids, hatch covers and instrument covers closed, wherever a latch would be too expensive or too clumsy for the door.
Instrument and equipment cabinets – A 40 N rectangular body on a sheet steel door, with the catch on the frame and the door itself as the plate.
Aluminium and stainless doors – A catch with a steel strike plate on the door, where the door material does not attract a magnet on its own.
Hatch and cover panels – A 52 N or 105 N body on a lid that has to stay shut in wind, with two catches on a wide lid rather than one heavy one.
Retrofit and field repair – An adhesive mount body on a panel that cannot be punched, or a bare disc bonded into a recess in a plastic door.
A magnetic catch is chosen by the pull it has to resist and the tolerance the door can absorb, and the SUPERB PCB cabinet drawing gives both, so the catch is ordered against the door mass rather than against the hole it fits. On the SUPERB PCBA route the catch is fitted after the door is painted, because a polypropylene body that is masked and baked loses its snap fit.
Sourcing and Cross-Reference
A catch is ordered by the pull it has to resist and the hole the frame already has. Send the door mass, the handle distance from the catch, the hole shape and the door material, and the part follows. A catch quoted from the hole alone is a catch that may be too weak for the door, and a weak catch shows up as a door that rattles rather than as a part that fails.
The plate is part of the order. A steel door needs no plate, a stainless or aluminium door needs one, and the plate has to be recessed or it holds the door off the frame. Where the door is plastic, the plate is bonded into a recess and the adhesive is chosen for the plastic rather than for convenience.
For a bare magnet, the pull figure is quoted against a thick steel plate, and a thin plate, a painted surface or an air gap reduces it. Where a door has to hold against a specific force, we quote the magnet with the gap stated, because the same disc at 1 mm and at 3 mm is two different parts in practice.
SUPERB Assembly fits a catch to the first door of a build, closes it twenty times and pulls it open with a spring gauge, because a catch that is rated 40 N on paper reads 28 N once the strike plate is 2 mm out of line.
Q: Can you supply 40 N snap in magnetic catches for a 1.2 mm steel door and the steel strike plates for an aluminium door in the same shipment?
A: Send the door mass, the door material, the frame thickness, the hole shape you can punch and the pull you need to resist. The SUPERB Tech desk quotes the catch with its rated load and hole shape, and the strike plate where the door is not steel.
Why Buy Catches and Magnets Through SUPERB
- Pull quoted with the door mass: The rated load and the handle distance are read together, so a door does not arrive with a catch that is too weak.
- Hole shape checked first: Rectangular, round and adhesive bodies are listed by the punching, so the frame does not have to be cut twice.
- Strike plates in the same order: A stainless or aluminium door is quoted with its plate rather than sent to a second supplier.
- Magnet grade and temperature stated: N52 with an 80 C limit, so the magnet is fitted after the paint line and not before.
- Small quantities and mixed colours: Black, white and natural bodies in one line, which suits a panel builder with a short run.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Draw Latches and Toggle Latches for Enclosure Doors, Continuous and Butt Hinges for Enclosure Doors, Enclosure Handles and Corner Guards for Portable Units, Silicone O Rings and Sealing Gaskets for Enclosures, Breather Vents and Pressure Equalization Plugs for Sealed Cases, Obsolete Part Cross Reference Hub.