Silicone O Rings and Sealing Gaskets for Enclosures
Product Specifications
Product Overview
An O ring is a simple part with an unforgiving rule: it seals because it is squeezed, and it is squeezed by the groove, not by the ring. The ring is a fixed section, and the groove depth decides how far that section is compressed when the lid is closed. Read the ring without the groove and the part is a number; read them together and it is a seal.
The size system on this page is AS568, the inch based series published by SAE. A dash number fixes both the inside diameter and the cross section, and the cross section families are 1.78 mm, 2.62 mm, 3.53 mm, 5.33 mm and 6.99 mm. A dash number in the 200 series always carries a 3.53 mm section, and the number after the series letter counts up through the inside diameters, so -214 is 24.99 mm inside diameter on a 3.53 mm section and -216 is 28.17 mm on the same section. That is why two rings that look the same on a bench are not interchangeable.
The 000 series is the smallest, with a 1.78 mm section and inside diameters from 4.47 mm at -008 to 63.22 mm at -037. It is the family for a connector shell, a small sensor body, a sight glass or a gland on a 6 mm cable. The 100 series steps up to a 2.62 mm section, from 9.19 mm at -110 to 72.69 mm at -150, and the 200 series uses the 3.53 mm section from 18.64 mm at -210 to 126.59 mm at -250. On an enclosure lid, the 200 series is the workhorse: the section is thick enough to absorb a little frame distortion and thin enough to close by hand.
Tolerance is part of the specification, not a detail. An AS568 ring carries a two way tolerance on the inside diameter that grows with the size, from about plus or minus 0.13 mm on the small sizes to about plus or minus 0.46 mm at a 53 mm inside diameter, and a cross section tolerance that stays near plus or minus 0.08 mm on the 1.78 mm section. A groove cut to a nominal depth with no allowance for the upper tolerance is a groove that over compresses the ring.
Squeeze is the number to agree before the drawing is released. On a face seal the ring is compressed between a flat lid and a flat flange, and the usual band is 20 to 30 percent of the section; on a radial static seal, where the ring sits in a groove on a piston or a bore, the band is nearer 10 to 15 percent. Take a 3.53 mm section at 25 percent and the groove is 2.65 mm deep. Take the same ring at 12 percent and it is 3.11 mm. Both figures come from the seal maker handbook for the compound, and both have to be on the drawing.
Where the joint is a flat lid rather than a groove, the part is a sponge gasket and the material is closed cell silicone. Saint-Gobain Norseal R10480S is the grade on this page: 332 kg per cubic metre, a compression deflection of 35 kPa at 25 percent, a compression set of 5 percent and a range of minus 73 to 260 C, recognised to UL 50E for electrical enclosure gaskets. It is supplied in 2.38, 3.18, 4.76, 6.35, 9.53 and 12.7 mm sheet. A denser silicone sponge at 250 kg per cubic metre and 90 kPa at 40 percent strain suits a lid that is clamped by screws rather than by hand.
Silicone is chosen over nitrile and EPDM for one reason: temperature range with retained elasticity. It holds from about minus 60 C to 200 C continuous, and to 250 C intermittent on the sponge grades, and it does not harden in UV the way a nitrile gasket does. It is not the material for a hydrocarbon or a fuel, and it has modest tear strength, so a gasket that is dragged across a thread should have a chamfer or a lead in on the lid.
Key Specifications
| Parameter | Value | Notes |
|---|---|---|
| Size standard | AS568 dash numbers, inch based | Also ISO 3601 metric sizes on request |
| Cross sections | 1.78 mm, 2.62 mm, 3.53 mm, 5.33 mm, 6.99 mm | 000, 100, 200, 300 and 400 series |
| Inside diameter range | 4.47 mm to 126.59 mm on the listed dash numbers | Larger sizes quoted to order |
| Inside diameter tolerance | About plus or minus 0.13 mm to 0.46 mm | Grows with the dash size |
| Cross section tolerance | About plus or minus 0.08 mm on the 1.78 mm and 2.62 mm sections | Per AS568 |
| Compound | Silicone, standard moulded grade | Other durometer to order with the part |
| Temperature range | About minus 60 C to 200 C continuous | Sponge grades to 250 C intermittent |
| Face seal squeeze | 20 to 30 percent of the section | Confirm on the gland drawing |
| Radial static squeeze | 10 to 15 percent of the section | Groove depth from the seal handbook |
| Sponge gasket density | 250 to 332 kg per cubic metre | Closed cell silicone |
| Sponge compression deflection | 35 kPa at 25 percent, or 90 kPa at 40 percent | Grade dependent |
| Sponge temperature range | Minus 73 C to 260 C on the low set grade | UL 50E recognised |
Included Models and Order Codes
The table lists the O ring dash numbers we quote most often for connector shells, sensor bodies and lid glands, with the section and the outside diameter that follows from it. The sponge gasket grades follow in the second table, because a flat lid is not sealed by a ring.
| Dash Number | Inside Diameter | Cross Section | Outside Diameter | Series |
|---|---|---|---|---|
| AS568-008 | 4.47 mm | 1.78 mm | 8.03 mm | 000 |
| AS568-010 | 6.07 mm | 1.78 mm | 9.63 mm | 000 |
| AS568-012 | 9.25 mm | 1.78 mm | 12.81 mm | 000 |
| AS568-014 | 12.42 mm | 1.78 mm | 15.98 mm | 000 |
| AS568-016 | 15.60 mm | 1.78 mm | 19.16 mm | 000 |
| AS568-018 | 18.77 mm | 1.78 mm | 22.33 mm | 000 |
| AS568-020 | 21.95 mm | 1.78 mm | 25.51 mm | 000 |
| AS568-022 | 25.12 mm | 1.78 mm | 28.68 mm | 000 |
| AS568-024 | 28.30 mm | 1.78 mm | 31.86 mm | 000 |
| AS568-030 | 41.00 mm | 1.78 mm | 44.56 mm | 000 |
| AS568-110 | 9.19 mm | 2.62 mm | 14.43 mm | 100 |
| AS568-112 | 12.37 mm | 2.62 mm | 17.61 mm | 100 |
| AS568-114 | 15.54 mm | 2.62 mm | 20.78 mm | 100 |
| AS568-116 | 18.72 mm | 2.62 mm | 23.96 mm | 100 |
| AS568-118 | 21.89 mm | 2.62 mm | 27.13 mm | 100 |
| AS568-210 | 18.64 mm | 3.53 mm | 25.70 mm | 200 |
| AS568-214 | 24.99 mm | 3.53 mm | 32.05 mm | 200 |
| AS568-216 | 28.17 mm | 3.53 mm | 35.23 mm | 200 |
| AS568-218 | 31.34 mm | 3.53 mm | 38.40 mm | 200 |
| AS568-220 | 34.52 mm | 3.53 mm | 41.58 mm | 200 |
| AS568-222 | 37.69 mm | 3.53 mm | 44.75 mm | 200 |
| AS568-224 | 44.04 mm | 3.53 mm | 51.10 mm | 200 |
| AS568-226 | 50.39 mm | 3.53 mm | 57.45 mm | 200 |
| AS568-228 | 56.74 mm | 3.53 mm | 63.80 mm | 200 |
| AS568-230 | 63.09 mm | 3.53 mm | 70.15 mm | 200 |
Silicone Sponge Gasket Grades
A flat lid is sealed by a sheet or a cord rather than by a ring. The two grades below cover a soft gasket for a hand closed lid and a firmer one for a lid that is drawn down by screws.
| Material | Density | Compression Deflection | Compression Set | Temperature | Supplied As |
|---|---|---|---|---|---|
| Silicone sponge, low compression set, UL 50E | 332 kg per cu m | 35 kPa at 25 percent | 5 percent | Minus 73 C to 260 C | Sheet 2.38 to 12.7 mm |
| Silicone sponge, medium density | 250 kg per cu m | 90 kPa at 40 percent strain | About 12 to 14 percent at 50 percent after 22 h at 70 C | Minus 60 C to 200 C | Sheet 1.5 to 12 mm, cord to order |
| Silicone sponge, FDA grade extruded | 300 kg per cu m | 50 kPa at 25 percent | 15 percent at 70 C for 22 h | Minus 50 C to 200 C | Cord and profile to order |
Key Features
Dash number fixes two dimensions – An AS568 dash number sets the inside diameter and the section together, so a -214 is 24.99 mm inside on a 3.53 mm section and is not interchangeable with a -114.
Squeeze stated, not assumed – The page gives the groove depth that a 20 to 30 percent face seal and a 10 to 15 percent radial seal produce for each section.
Silicone for the outdoor cabinet – Elasticity is retained from about minus 60 C to 200 C, which is what a lid on a mast or a roof needs through a winter.
Sponge for the flat lid – Closed cell silicone at 250 to 332 kg per cu m takes the place of a ring where the joint is a flat sheet rather than a groove.
Gasket set that stays set – The low compression set grade is 5 percent on the supplier data, so a lid that is opened ten times a season still seals on the eleventh.
Materials matched to the fluid – Silicone where temperature and UV rule, nitrile or EPDM where oil or steam is in the line, quoted per application.
Applications
These seals go on enclosure lids, connector shells, sensor bodies, sight glasses and cable glands, wherever a joint has to stay dry through a temperature swing.
Outdoor and masthead enclosures – A 200 series ring on the lid gland, or a 6 mm sponge cord in a machined groove, with silicone for UV and a 40 C night to a 75 C day.
Sensor and transducer bodies – Small 000 series rings, 4.47 mm to 28.30 mm inside diameter, on a threaded body that is sealed against wash down.
Instrument lids with flat flanges – A closed cell silicone sheet gasket at 3.18 or 6.35 mm, cut to the flange, on a lid drawn down by M4 screws.
Medical and laboratory housings – Silicone on a housing that is wiped down with an alcohol, with the compound and the hardness stated on the drawing.
A seal is chosen against the groove, the fluid and the temperature, so the dash number and the compound are read together with the gland drawing that the SUPERB PCB enclosure carries. On the SUPERB PCBA side the gasket is fitted to the lid after conformal coating, because a seal that is already in place collects overspray and then leaks.
Sourcing and Cross-Reference
Seals are quoted from the gland drawing rather than from the ring size, because the groove is what makes the part work. Send the groove width, the groove depth, the inside diameter and the fluid, and the dash number follows. Send only the inside diameter and the answer is a ring that may be right for the bore and wrong for the squeeze.
Compound matters as much as size. Silicone is the default for temperature and UV, but it swells in some oils and has modest tear strength. Where the line carries a hydrocarbon, a nitrile or an FKM ring is quoted in the same dash size. The size system does not change with the compound, so the drawing stays the same and only the material code moves.
For obsolete or special sizes, the substitute is chosen on section and squeeze, not on the nearest diameter. A 3.53 mm section replaced with a 2.62 mm section in the same groove is a seal that is under compressed and weeps. We check the groove depth before we offer the alternative, and we say when a metric ISO 3601 size is the closer match.
SUPERB Assembly checks the squeeze on the first lid of a build by measuring the gasket section before and after the screws are torqued, because a sponge cord that is compressed twice as far as its maker allows takes a set and never seals again.
Q: Can you supply AS568-214 silicone O rings and confirm the groove depth for a 25 percent squeeze on our lid, and quote a 6.35 mm sponge gasket in the same order?
A: Send the groove width and depth, the inside diameter of the gland, the fluid, the temperature range and the IP rating you have to meet. The SUPERB Tech desk quotes the dash number and the compound, and states the squeeze the groove will give.
Why Buy Seals Through SUPERB
- Gland checked before the part is quoted: Groove depth, width and inside diameter are read together, so the ring arrives with the squeeze you planned.
- Compound and size quoted separately: The same dash number in silicone, nitrile, EPDM or FKM, with the temperature and fluid stated for each.
- Ring and flat gasket from one desk: An enclosure that needs a ring on the gland and a sponge sheet on the lid is quoted as one seal package.
- Tolerance on the drawing: AS568 inside diameter and section tolerances are stated with the part, which is what an inspection sheet has to reference.
- Small and mixed quantities: Ten rings and one sheet are quoted together, which suits a service build rather than a production run.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Breather Vents and Pressure Equalization Plugs for Sealed Cases, Nylon Grommets and Hole Plugs for Panel Openings, Cable Clamps and Harness Ties for Internal Wiring, EMI Shielding Cans and Contact Gaskets for RF Boards, Draw Latches and Toggle Latches for Enclosure Doors, BOM Shortage Recovery.