Contact Us
  • Home
  • COMPONENTS
  • Cam Locks and Key Locking Latches for Enclosure Doors

Cam Locks and Key Locking Latches for Enclosure Doors

A cam lock holds a door with a cam that swings behind the frame in a quarter turn, and a compression latch adds a 6.4 mm pull up that squeezes the gasket. The family here covers 13.5 mm and 19.1 mm bodies in zinc plated steel, aluminium, 304 and 316 stainless and moulded stainless, keyed and tool operated. Grip is the number that decides the part: door thickness plus compressed gasket plus frame thickness, with a 3.2 mm to 58 mm range across the cams listed. Every latch is rated 450 N static load and reaches NEMA 4 and IP65 with the flange gasket fitted.
quote now

Product Specifications

Product Overview

A cam lock is a single hole fixing with a cam on the back. The key or the tool turns a shaft, the cam swings from the free position to a position behind the frame, and the door is held by the cam rather than by a bolt. One hole, one nut, no striker plate and no alignment between two parts, which is why the part is used on cabinets, rack doors, meter boxes and test enclosures where the door is sheet steel and the frame is a folded edge.

There are two actions in this family and they solve different problems. A plain cam lock turns the cam behind the frame and stops there: the door is held shut, but the gasket is not squeezed, so the seal depends on the door being flat against the frame. A compression latch turns the cam behind the frame in the first part of the travel and then draws the door forward by 6.4 mm in the second part, which compresses a flange gasket and holds the door against vibration with an over centre action. A gasketed cabinet needs the second action, and that is the difference that most often decides whether a cabinet passes its leak test.

Grip is the number that decides which part fits, and it is not the door thickness. Grip is the door thickness plus the compressed thickness of the gasket plus the frame thickness, measured at the point the cam sits behind. A 2 mm steel door, a 1.5 mm frame and a gasket that compresses from 4 mm to 1 mm gives a total grip of 4.5 mm, and that number picks the cam. Where the sum falls between two cams, the smaller cam is chosen, because a cam that is too short leaves the gasket slack while a cam that is too long cannot be closed at all. Getting this wrong is the single most common reason a latch is returned.

The bodies in this family come in two sizes. The 19.1 mm body is the one for a cabinet door and it is available in machined 304 and 316 stainless, in cast 316 stainless, in zinc plated steel, in aluminium and in moulded stainless, with a maximum static load of 450 N and a maximum door thickness of 18 mm including the gasket. The 13.5 mm body is the compact size for a small enclosure, an instrument case or a panel that has no room for a 22.5 mm hole, and it uses an 8 mm grip range in eight steps from 3.2 mm to 28.6 mm rather than a separate cam.

Access is a separate decision from the body. The same 19.1 mm housing takes a double bit head, a 7 mm triangle, a 7 mm square, an 8 mm hex recess, a slotted recess, an 8 mm square, a railway standard head or a Bellcore 216 head, and the keyed versions take a tubular key. Two key codes appear in this range, CH751 and R001. CH751 is the common cabinet code and is used where a fleet of cabinets is opened with one key, while R001 is the code for a site that wants its own key and does not want a universal one. Keys are ordered as a single or as a pair, and a padlock bracket is available for the 19.1 mm tool operated body where a padlock rather than a key is the security.

The cam is ordered with the latch and not instead of it, and the cam type sets both the grip and the room the cam needs inside the door. A deep offset cam reaches past a deep frame return, a straight cam is the one for a flat frame, and a reversed cam turns the offset the other way for a frame that sits proud of the door. The cam tables in this range run in 2 mm steps on the hand operated body and in fixed ranges on the tool operated body, so a grip that is between two steps is rounded down rather than guessed.

The rating that matters in a sealed cabinet is the load on the latch and the fire and vibration approvals that the cabinet has to carry. The stainless versions of the 19.1 mm body are listed to EN 45545-3 E60 for rail work, the aluminium version is listed against DIN EN 61373 for vibration, and the whole family reaches NEMA 4 and IP65 with the flange gasket fitted. A cabinet that is washed down needs the stainless body and the gasket, because a zinc plated body with no gasket is a wet joint that rusts from the inside.

Installation is one hole and one nut, and the internal protrusion is the number to check against the components behind the door. The 19.1 mm body needs a 22.5 mm hole and an M22 x 1.5 mounting nut, and it sits 13 mm to 18 mm behind the door face depending on the grip. The three hole version spreads the load on a thin door that would otherwise pull in around a single nut. Where the door is a composite or a plastic, the three hole version with a backing plate is the safer fixing, because a plastic door creeps under a single nut and the latch comes loose after a season.

Key Specifications

ParameterValueNotes
Body sizes13.5 mm and 19.1 mm19.1 mm is the cabinet door size
Body materialsZinc plated steel, aluminium, 304 and 316 stainless, moulded stainlessStainless for washdown and rail
Access stylesDouble bit, 7 mm triangle, 7 mm square, 8 mm hex, slotted, 8 mm square, tubular keyRailway and Bellcore 216 heads also listed
Compression on the latch versions6.4 mm (0.25 in) pull upCompresses the flange gasket
Maximum static load450 N (102 lbf)19.1 mm body
Maximum door thickness18 mm including gasket19.1 mm body
SealingNEMA 4 and IP65 with the flange gasketGasket is a separate part on some bodies
Fire ratingEN 45545-3 E60 on the stainless versionsRail and transit cabinets
VibrationDIN EN 61373 on the aluminium versionRoad and rail mounting
MountingSingle hole 22.5 mm with M22 x 1.5 nut, or three holeThree hole for thin and plastic doors
Grip range across the cams3.2 mm to 58 mmDoor plus compressed gasket plus frame
Cam typesDeep offset forward and reversed, offset forward and reversed, straightCam ordered separately
Key codesCH751 and R001Keyed alike or keyed to a site code

Included Models and Order Codes

The bodies are listed first with the access and the grip they carry, then the keys and the gasket that complete an order. A body without a cam is a shaft and a head: the cam number is what makes it a latch, and it is quoted against the grip rather than against the body.

Part NumberTypeSizeMaterial or FinishGripNotes
E3-125-182Latch, key locking, fixed grip19.1 mmStainless, electropolished51 to 53 mmTubular key, IP65, 450 N static load
E3-28-201-12Cam, deep offset, forward19.1 mm bodySteel3.3 to 19 mmOrdered with the body
E3-28-202-12Cam, offset, forward19.1 mm bodySteel17 to 32.7 mmOrdered with the body
E3-28-203-12Cam, straight19.1 mm bodySteel30.7 to 46.4 mmFlat frame
E5-17Flange gasket13.5 mm bodyRubberNot applicableSealing for the compact body
PK-10-10-05Key, single19.1 mm latchesOvermoulded, CH751Not applicableOne key
PK-10-01-05Key, pair19.1 mm latchesOvermoulded, CH751Not applicableTwo keys, keyed alike
PK-10-01-05-KR001Key, pair19.1 mm latchesOvermoulded, R001Not applicableSite code, two keys
PK-10-01Key, pair, flat19.1 mm latchesSteelNot applicableFlat key pair

Cam Part Numbers and Grip Steps

A cam is a separate line on the order and the grip it covers is printed on it. The hand operated 19.1 mm body takes a cam in 2 mm steps from 15 mm to 53 mm in zinc plated steel, or from 20 mm to 58 mm in 304 stainless, and the tool operated body takes the three range cams below.

Part NumberCam TypeGripMaterialFits
E5-2500Offset cam15 mmSteel, zinc plated19.1 mm hand operated body
E5-2505Offset cam25 mmSteel, zinc plated19.1 mm hand operated body
E5-2510Offset cam35 mmSteel, zinc plated19.1 mm hand operated body
E5-2515Offset cam45 mmSteel, zinc plated19.1 mm hand operated body
E5-2519Offset cam53 mmSteel, zinc plated19.1 mm hand operated body
E5-1200-24Offset cam20 mm304 stainless19.1 mm stainless body
E5-1210-24Offset cam40 mm304 stainless19.1 mm stainless body
E5-1219-24Offset cam58 mm304 stainless19.1 mm stainless body
E3-28-700-24Compact cam4 mmStainless19.1 mm compact body
E3-28-710-24Compact cam24 mmStainless19.1 mm compact body
E3-28-719-24Compact cam42 mmStainless19.1 mm compact body

Key Features

Quarter turn with a cam behind the frame – One hole, one nut and no striker plate, so the door needs no alignment between two parts.

6.4 mm compression on the latch versions – The second half of the turn draws the door forward, which is what actually compresses the flange gasket.

Grip stated as a number – Door plus compressed gasket plus frame, with cams from 3.2 mm to 58 mm, so the part is chosen from the arithmetic rather than by eye.

Two body sizes – A 19.1 mm body for a cabinet door and a 13.5 mm body for an instrument case with no room for a 22.5 mm hole.

Keyed and tool operated access – Tubular key in CH751 or R001, or a double bit, triangle, square, hex or slotted head where a key is not wanted.

450 N static load – The single hole body holds a 450 N static load, which is well beyond the pull a person puts on a cabinet door.

Stainless, aluminium and plated steel – Washdown and rail cabinets take the stainless body, and the aluminium version carries the DIN EN 61373 vibration listing.

Padlock bracket available – The 19.1 mm tool operated body takes a bracket for a padlock where the site wants a lock rather than a key.

Applications

These locks go on cabinet doors, rack doors, meter and test enclosures, hatch covers and instrument cases, wherever a door has to stay shut against a gasket or a vibration.

Outdoor and washdown cabinets – A 19.1 mm stainless body with a tubular key and a flange gasket, on a door that is hosed down once a month.

Rack and server doors – A 19.1 mm zinc plated body with a CH751 key, so one key opens a whole rack of cabinets.

Rail and transit cabinets – A machined stainless body listed to EN 45545-3 E60, with the three hole fixing on a thin door.

Instrument and meter cases – A 13.5 mm body with a knob or a hex head on a case with a 8 mm grip, where a 22.5 mm hole will not fit.

A sealed door only stays sealed if the latch pulls the gasket down, and the SUPERB PCB cabinet panel drawing states the door thickness, the gasket and the frame before the lock is ordered. On the SUPERB PCBA route the lock goes in after the door is painted, because a masked body holds paint in the keyway and the key stops turning.

Sourcing and Cross-Reference

A lock is ordered from three numbers: the grip, the access style and the body material. Send the door thickness, the frame thickness and the gasket compression, and say whether the site needs a key code of its own. Where only the door is known, the gasket is the part that is usually forgotten, and a gasket that compresses from 4 mm to 1 mm changes the grip by 3 mm, which moves the order to a different cam.

A body and a cam are two lines, and a body quoted on its own will not latch a door. When a customer sends a drawing with a hole and no grip, the answer is a question about the frame and the gasket rather than a part number, and that question is cheaper than a returned latch.

Where a lock replaces another make, the grip and the hole are the two things to match, not the outline. A 22.5 mm hole and the same grip is the cross reference, and the access style can change on the same body without touching the door. Where the hole is 19 mm or a different key code is standard on the panel, the answer is a body change and not an adapter.

SUPERB Assembly fits the lock to the first door of a build and checks the grip with a feeler gauge between cam and frame, because a grip that is 2 mm long leaves the gasket uncompressed and the cabinet fails its leak test at the end of the line.

Q: Can you supply a 19.1 mm key locking latch with the CH751 code, a cam for a 6 mm grip and the flange gasket, in stainless, for a washdown cabinet?

A: Send the door thickness, the frame thickness, the compressed gasket thickness, the hole you can punch and the key code you need. The SUPERB Tech desk adds the three thicknesses into a total grip, picks the cam from that number and quotes the body and the cam together, because a latch body arrives without a cam on it.

Why Buy Door Locks Through SUPERB

  1. Grip worked out before the order: Door, gasket and frame are added together, so the cam that arrives fits the door that was drawn.
  2. Body, cam and key on one line: A latch, its cam and its key pair are quoted together, which avoids a body on the shelf with no way to close it.
  3. Key codes kept per site: CH751 for a fleet and R001 for a site that wants its own key, recorded against the order so a replacement matches.
  4. Stainless and rail versions listed: EN 45545-3 E60 and DIN EN 61373 versions are named, rather than a cabinet being approved on a plated body.
  5. Short runs and spares: A handful of bodies and cams is quoted as one line, which suits a panel builder who needs a spare for each cabinet type.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Draw Latches and Toggle Latches for Enclosure Doors, Continuous and Butt Hinges for Enclosure Doors, Enclosure Handles and Corner Guards for Portable Units, Captive Panel Screws and Quarter Turn Fasteners, Silicone O Rings and Sealing Gaskets for Enclosures, Obsolete Part Cross Reference Hub.