Contact Us
  • Home
  • COMPONENTS
  • Calibration Buffers and Conductivity Standards for pH Analysers

Calibration Buffers and Conductivity Standards for pH Analysers

A pH or conductivity reading is only as good as the standard behind it. A buffer that has absorbed carbon dioxide, or a conductivity standard diluted with the wrong water, moves the calibration without any alarm. This page lists certified pH buffers from 1.679 to 12.45 and KCl conductivity standards from 25 microsiemens to 111.3 millisiemens per centimetre, with the uncertainty of each. The table also gives the value at 20 and at 25 C where the maker publishes both, because a standard used at the wrong temperature reads low by about two percent per degree. Colour coded technical buffers are listed next to the certified reference materials, so a routine calibration and a method validation can draw from the same page.
quote now

Product Specifications

Product Overview

A calibration standard is a reference material, and the two things that matter are the assigned value and the uncertainty. A technical buffer assigned at 4.01 with a tolerance of plus or minus 0.02 is fine for a routine check on a process electrode. A certified reference material assigned at 4.005 with an uncertainty of plus or minus 0.010 is what a method validation or an audit asks for. Both are on this page, and the difference is in the certificate rather than in the bottle.

Temperature is the most common source of error. A conductivity standard has two assigned values, one at 20 C and one at 25 C, and they are not close: one family reads 133 microsiemens at 20 C and 147 at 25 C, 1274 and 1408 microsiemens, and 11.64 and 12.85 millisiemens. A meter that compensates to 25 C and a standard used at 20 C will disagree by about ten percent unless the temperature is entered. A pH buffer moves less, but a buffer calibrated at 20 C and used at 37 C still drifts, which is why the assigned temperature is printed on the bottle.

Handling decides how long the value holds. A buffer left open absorbs carbon dioxide and its pH falls, most quickly in the alkaline range, so a pH 10 buffer has the shortest open life. A conductivity standard left open concentrates by evaporation and reads high. Published open life runs two to three months for a 500 mL bottle, and the certificate life of 18 to 36 months applies only to an unopened bottle. A laboratory that calibrates daily should use a small sachet or a pour top rather than a large bottle that is opened twenty times a week.

The range of standards should match the range of the measurement. For conductivity, a 84 microsiemens standard covers the 0 to 200 microsiemens decade, 1413 microsiemens covers 200 to 2000, and 12.88 millisiemens covers 2 to 20 millisiemens. Using a 12.88 millisiemens standard to calibrate a meter that reads drinking water puts the calibration point two decades above the reading, and the error at the low end is not visible in the calibration. For pH, the pair should bracket the working value, so a pH 4.01 and 7.00 pair for an acidic process and a 7.00 and 10.01 pair for an alkaline one.

Key Specifications

ParameterValueNote
pH range covered1.679, 4.005, 6.865, 7.000, 9.180, 10.012 and 12.45the 6.865 and 9.180 values are the NIST and DIN pair
pH uncertainty, certifiedplus or minus 0.010 for 1.679 to 10.012, plus or minus 0.05 at 12.45certified reference material with a certificate
pH uncertainty, technicalplus or minus 0.024.01, 7.00 and 10.01 colour coded buffers
pH traceabilityNIST and DIN 19266, or IUPAC for the certified seriesstated on the certificate
Conductivity range25 microsiemens to 111.3 millisiemens per centimetreKCl and NaCl standards
Conductivity uncertaintyplus or minus 1 percent on the KCl standards, plus or minus 2.5 percent at 146.9 microsiemensthe low decade carries the wider tolerance
Conductivity traceabilityNIST and OIMLKCl 1D, 0.1D and 0.01D grades
Assigned temperature20 C and 25 C values published for the conductivity seriesthe two differ by about ten percent
Open life2 to 3 months after opening18 to 36 months unopened, per the certificate
Packaging500 mL bottle, 250 mL bottle, 20 mL sachet, powder pillowa sachet avoids repeated opening of a large bottle
Colour codingred 4.01, yellow 7.00, blue 10.01reduces a wrong buffer in a routine calibration
Storage15 to 25 C, out of direct light, cap closeddo not store a buffer in a beaker
Certificatesingle lot certificate with the assigned value and uncertaintyrequired for a validated method

Included Models and Order Codes

The first block is certified pH reference material, the second is conductivity reference material, the third is the routine technical buffer used for daily calibration. The value in the table is the assigned value at 25 C unless the row says otherwise, and the uncertainty is the maker figure for that lot series, not a general claim.

PartTypeAssigned valueUncertaintyPackNote
S11M001pH certified reference material, IUPAC1.679 pHplus or minus 0.010500 mLacidic end, rarely used on a process line
S11M002pH certified reference material4.005 pHplus or minus 0.010500 mLfirst point of an acidic pair
S11M003pH certified reference material6.865 pHplus or minus 0.010500 mLNIST neutral point, not 7.000
S11M004pH certified reference material7.000 pHplus or minus 0.010500 mLthe 7.000 value used by most process meters
S11M006pH certified reference material9.180 pHplus or minus 0.010500 mLalkaline point of the NIST series
S11M007pH certified reference material10.012 pHplus or minus 0.010500 mLalkaline point of the DIN series
S11M008pH certified reference material12.45 pHplus or minus 0.05500 mLwidest tolerance, shortest open life
S51M001Conductivity CRM, KCl 1D, OIML111.3 mS/cmplus or minus 1 percent500 mLhigh decade, for brine and seawater
S51M002Conductivity CRM, KCl 0.1D12.85 mS/cmplus or minus 1 percent500 mLthe 2 to 20 mS decade
S51M003Conductivity CRM, KCl 0.01D1408 uS/cmplus or minus 1 percent500 mLthe 200 to 2000 uS decade
S51M004Conductivity CRM, 0.05 percent NaCl1015 uS/cmplus or minus 1 percent500 mLNaCl matrix, not KCl
S51M013Conductivity CRM, NaCl25 uS/cmper certificate250 mLpure water range
C20C250KCl conductivity standard12.88 mS/cm at 25 Cplus or minus 1 percent500 mLthe meter calibration point for most benchtop units
C20C270KCl conductivity standard1413 uS/cm at 25 Cplus or minus 1 percent500 mLthe common single point calibration
C20C280KCl conductivity standard146.9 uS/cm at 25 Cplus or minus 2.5 percent500 mLlow decade, wider tolerance
2283449pH technical buffer, NIST4.01 pH at 25 Cplus or minus 0.02500 mLred, routine calibration
2283549pH technical buffer, NIST7.00 pH at 25 Cplus or minus 0.02500 mLyellow, routine calibration
2283649pH technical buffer, NIST10.01 pH at 25 Cplus or minus 0.02500 mLblue, routine calibration
HI70030Conductivity standard sachet12.88 mS/cm at 25 Cper certificate20 mLsingle use, no open bottle
HI70031Conductivity standard sachet1413 uS/cm at 25 Cper certificate20 mLsingle use, for field meters

Which Standard for Which Reading Range

A standard is chosen to sit inside the reading range, not at the top of the meter scale. The table is the short form used when a calibration procedure is written, and it also shows where a second point is needed.

Reading rangepH buffer pairConductivity standardSecond pointWhy
Acidic process, pH 2 to 54.01 and 7.00not applicable7.00 as the checkthe pair brackets the working value
Neutral process, pH 6 to 86.865 and 7.000, or 4.01 and 7.00not applicablethe second buffer is the slope check6.865 and 7.000 are close, so use 4.01 for slope
Alkaline process, pH 9 to 127.00 and 10.01not applicable10.01 as the checkan alkaline buffer absorbs carbon dioxide fastest
Pure water, 0 to 200 uS/cmnot applicable84 or 146.9 uS/cmnone below 100 uSa high standard puts the point two decades away
Drinking water, 200 to 2000 uS/cmnot applicable1413 uS/cm12.88 mS/cm if the range is widethe common single point calibration
Brine and seawater, 2 to 20 mS/cmnot applicable12.88 mS/cm111.3 mS/cm for the top decadethe low standard is below the working range

Key Features

Certified pH values from 1.679 to 12.45 – the 6.865 and 9.180 NIST values sit next to the 7.000 and 10.012 DIN values, so a method written to either convention is covered

Uncertainty stated per part – plus or minus 0.010 on the certified series and plus or minus 0.02 on the technical buffers, which is the difference an audit looks for

Conductivity from 25 uS/cm to 111.3 mS/cm – the same list covers a pure water loop and a brine line

20 C and 25 C values – the table shows why a standard used at the wrong temperature reads about ten percent away

Open life on the label – 2 to 3 months after opening, against 18 to 36 months unopened, so a large bottle is not kept for a year

Single use sachets – a 20 mL sachet removes the carbon dioxide uptake that a repeatedly opened bottle collects

Colour coded technical buffers – red, yellow and blue for 4.01, 7.00 and 10.01, which cuts a wrong buffer in a routine calibration

KCl and NaCl standards listed separately – a meter calibrated on KCl and checked on NaCl shows a matrix difference, not a fault

Applications

Standards are consumed in three places: the daily calibration, the verification after a maintenance, and the method validation. Each one has a different tolerance requirement.

Process pH loops – a pH electrode on a reactor is calibrated against 4.01 and 7.00 every week and checked against a grab sample. The technical buffers are enough for the weekly routine, and the certified 4.005 and 7.000 materials are used when the loop is part of a validated batch record.

Conductivity in water treatment – a reverse osmosis skid reads 5 to 50 microsiemens. A 84 or 146.9 microsiemens standard sits inside that decade, and a 12.88 millisiemens standard is used only for the cell constant check, because it is two decades above the working point.

Laboratory and clinical analysers – an analyser with an internal pH and conductivity module needs a single use standard per shift. The 20 mL sachets are opened once and discarded, which keeps the open bottle problem out of a 24 hour line.

The analyser boards behind these calibrations are the kind of build SUPERB PCB and SUPERB PCBA programmes cover, from the electrode front end to the display board.

Sourcing and Cross-Reference

A buffer is ordered by value, uncertainty and pack size, and the pack size is the field that decides the cost per calibration. A 500 mL bottle is cheaper per millilitre, but if it is opened daily for three months the value at the end is not the value on the certificate. A 20 mL sachet costs more per millilitre and less per valid calibration. We quote both and let the calibration interval decide.

Where a method names a standard that is no longer supplied, the substitute has to match the traceability chain, not just the value. A 1413 microsiemens standard and a 1408 microsiemens standard are both KCl at about 0.01 molar, but they are assigned to different nominal values, and a method that names 1408 needs the OIML grade rather than the technical one.

Transport and storage are part of the specification. A buffer that freezes in transit can separate, and a conductivity standard that is stored above 25 C concentrates. We ship in the maker pack with the lot certificate and state the storage band, because a standard that has been mistreated is worse than no standard at all.

Where a skid is assembled with its standards and probe kit, the set is picked together, which is how SUPERB Assembly ships an analyser package.

Q: Can you supply a certified pH buffer with the certificate for a specific lot when our method names the value?

A: SUPERB Tech can confirm the assigned value, the lot certificate and the pack size against the method before the order is placed.

Why Buy Calibration Standards from SUPERB

  1. Value and uncertainty quoted together: a standard is never offered on pH value alone, since the tolerance is what decides whether it suits a validated method
  2. Certified and technical grades on one page: the routine calibration and the audit sample can be ordered from the same list
  3. Assigned temperature stated: 20 C and 25 C values are both given where the maker publishes them
  4. Pack size matched to the interval: 500 mL, 250 mL, 20 mL sachets and powder pillows, so a daily calibration is not run from a bottle opened for a year
  5. Lot certificate in the delivery file: the assigned value and the uncertainty travel with the goods

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: pH and ORP Electrodes for Process Analysers, Conductivity Cells and Toroidal Sensors for Water Analysers, Water Quality Sensor Circuits for pH, Conductivity and Dissolved Oxygen, Immersion Assemblies and Sample Probes for Online Analysers, Inline Filters and Frits for Reagent Lines, Component Lead Time Solutions.

Actual product photos available on request