Contact Us
  • Home
  • COMPONENTS
  • Adhesive Standoffs and PCB Mounting Pads for Board Fixing

Adhesive Standoffs and PCB Mounting Pads for Board Fixing

Nylon standoffs on a double sided adhesive base, from 3.5 mm to 19.1 mm, for a board that has no room for a mounting hole or a screw boss. The pad sticks to the chassis, the board snaps onto the locking head, and a release tab lets the board come off again without tools. Three head sizes cover 1.2 mm to 1.6 mm board thickness, in a body rated UL94 V-2.
quote now

Product Specifications

Product Overview

A board needs support at the middle as well as at the corners. Without it, a 1.6 mm board with a heavy transformer or a long connector flexes under its own weight, and the solder joint at the edge of the flex cracks after a few thermal cycles.

Where the chassis has no hole and no room for a boss, the standoff is stuck on. The base is a nylon pad with a double sided acrylic tape and a release tab, the body rises to the standoff height, and the head snaps through the board and locks it. The board can be released by pinching the head, which matters during test and rework.

The number that decides the part is the standoff height, not the base size. Height is the gap between the chassis and the underside of the board, and it has to clear the tallest component on the bottom side plus a margin for the solder joint and the conformal coat. A height that is 0.5 mm short presses the board onto a via and a height that is 3 mm long lets the board rock.

The head size follows the board thickness. The 3.5 mm head takes a 1.2 to 1.6 mm board, the 3.0 mm head takes a 1.2 to 1.6 mm board with a tighter grip and the 2.0 mm head takes a 1.6 mm board. All three are nylon 6/6 with a UL94 V-2 rating, and the adhesive is a rubber based tape with a shelf life of about one year in the unopened bag.

Key Specifications

ParameterValueNotes
Body materialNylon 6/6, naturalUL94 V-2
AdhesiveRubber based double sided tape, 0.8 mmRelease tab on the pad
Base diameter14.0 mm on type 1 and type 2, 12.7 mm on type 4The base is the bonding area
Standoff height3.5 mm to 19.1 mmHeight is the gap under the board
Head typeSnap lock, releasable by pinchingBoard is fitted after the base is stuck
Top hole3.5 mm, 3.0 mm or 2.0 mmMatched to board thickness
Board thickness1.2 to 1.6 mm, or 1.6 mm for the 2.0 mm headCheck the head against the board
Shelf lifeAbout 1 year from shipmentUnopened bag, room temperature, away from sunlight
Service temperatureLimited by the adhesive, not the nylonKeep the joint away from a heatsink

Included Models and Order Codes

The part number carries the head type and the height. CBABS1 is the 3.5 mm head, CBABS2 the 3.0 mm head and CBABS4 the 2.0 mm head, and the last three digits are the height in thousandths of an inch. Only the heights that are confirmed on both the maker table and the catalogue are listed here, so a height that is missing from this table is still available but quoted on request.

Part NumberHead typeStandoff heightBase diameterTop holeBoard thickness
CBABS105AType 1, snap lock3.5 mm14.0 mm3.5 mm1.2 to 1.6 mm
CBABS115AType 1, snap lock6.4 mm14.0 mm3.5 mm1.2 to 1.6 mm
CBABS215AType 2, snap lock6.4 mm14.0 mm3.0 mm1.2 to 1.6 mm
CBABS220AType 2, snap lock8.0 mm14.0 mm3.0 mm1.2 to 1.6 mm
CBABS225AType 2, snap lock10.0 mm14.0 mm3.0 mm1.2 to 1.6 mm
CBABS420AType 4, snap lock11.1 mm12.7 mm2.0 mm1.6 mm
CBABS430AType 4, snap lock15.9 mm12.7 mm2.0 mm1.6 mm
CBABS435AType 4, snap lock19.1 mm12.7 mm2.0 mm1.6 mm

Screw Mounted Supports in the Same Height Steps

Where the chassis can take a screw, the same heights are available on a screw mounted body. The CBSB and CBSBT series use a 4.8 mm to 15.9 mm standoff with a locking or a snap fit head, which is the right choice on a metal chassis that is earthed and cannot rely on a taped joint. The height steps match the adhesive parts, so a board can mix the two fixing methods without changing the stack.

Part NumberSeriesStandoff heightPack
CBSB-3-01A2-RTScrew mount, type 24.8 mm1000
CBSB-4-01A2-RTScrew mount, type 26.4 mm1000
CBSB-6-01A2-RTScrew mount, type 29.5 mm1000
CBSB-8-01A2-RTScrew mount, type 212.7 mm1000
CBSB-10-01A2-RTScrew mount, type 215.9 mm1000
CBSBT-5-01A2-RTScrew mount, type 47.9 mm1000
CBSBT-7-01A2-RTScrew mount, type 411.1 mm1000
CBSBT-9-01A2-RTScrew mount, type 414.3 mm1000

Key Features

No hole in the chassis – The pad bonds to a flat surface, so a board can be supported where drilling or tapping is not possible.

Heights from 3.5 mm to 19.1 mm – The gap under the board clears the tallest bottom side part plus the solder joint and the coating.

Release tab on the pad – The tape is applied with a tab that stays above the surface until it is pulled, which is faster than peeling a liner with a knife.

Board snaps off and back on – The head is a snap lock that can be pinched open, so the board comes out for test, rework or a firmware swap and goes back without a new standoff.

Three head sizes – A 3.5 mm, 3.0 mm and 2.0 mm head cover 1.2 mm to 1.6 mm boards with a grip that does not crush the laminate.

UL94 V-2 nylon – The body carries the flame rating that a panel review asks for, and the natural colour shows contamination on the assembly.

Same heights on a screw body – The screw mounted series uses the same height steps, so one stack height works with either fixing method.

Tape thickness stated – The 0.8 mm tape is part of the stack and is included in the height budget, which is the number that is usually missed.

Applications

Adhesive standoffs are used where a board has to be held away from a surface that cannot be drilled. The four cases below are the common ones.

Sheet metal enclosures – A controller board is supported at the middle on a painted plate, where a drilled hole would break the paint and start a corrosion point.

Potting and conformal coat – The pad keeps the board off the plate so the coating can flow under it, and the height sets the coating thickness at the gap.

Retrofit and repair – A board that was held by a bracket that is no longer available is re-supported with a pad and a standoff, without touching the chassis.

Low volume and prototype builds – A taped standoff avoids a tooling change on a short run, and the height can be changed without a new plate.

A taped standoff is only as good as the surface under it, so the SUPERB PCB assembly drawing names the plate finish and the gap under the board. On the SUPERB PCBA build the pads are pressed before the board is placed, and the height is checked with a gauge at the first article.

Sourcing and Cross-Reference

The height is the specification, and it is measured from the chassis to the underside of the board. A customer who sends a board thickness and a component height gets a part that fits; a customer who sends a part number gets what the number says, which may be 2 mm out of the stack.

The adhesive is the weak point, not the nylon. A taped joint holds on a clean, flat, painted surface at room temperature, and it loses grip on a rough casting, a powder coat with a heavy texture or a surface that runs above 60 C. Where any of those apply, the screw mounted body in the same height step is the honest answer.

The parts are packed 1000 to a bag, and the tape has a shelf life of about a year. A bag that has been open on a shelf for two years is not a bag to build with, which is the reason the date is on the label and not only in the catalogue.

SUPERB Assembly cleans the plate, presses each pad for the dwell time on the tape data sheet and snaps the board down at the corners first, because a board that is pressed at the middle bows the standoff out of the pad.

Q: Can you supply CBABS115A in the 6.4 mm height with the 3.5 mm head, and the CBSB-4 screw mounted body at the same height, for a 1.6 mm board?

A: Send the board thickness, the tallest component on the bottom side, the plate finish and the temperature at the pad. The SUPERB Tech desk replies with the height, the head size and, where the surface is rough or hot, the screw mounted body at the same height.

Why Buy Adhesive Standoffs Through SUPERB

  1. Height checked against the stack: The board thickness, the bottom side component and the coating are added before the part is quoted, so the gap is right the first time.
  2. Adhesive matched to the surface: A taped pad is quoted for a clean flat plate, and a screw body is offered where the surface is rough or hot.
  3. Same height on both fixings: Taped and screwed bodies share the height steps, so a mixed board does not need two stack heights.
  4. Releasable head: The snap lock opens by hand, which keeps a test or rework loop from consuming a new standoff each time.
  5. Board assembly support: The assembly team presses the pad, checks the height with a gauge and snaps the board down, so the gap is measured rather than assumed.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Standoffs, Spacers and Mounting Hardware for Board Stacks, Anti Vibration Mounts and Rubber Isolators, Captive Panel Screws and Quarter Turn Fasteners, Thermal Gap Pads and Heat Sinks for Board Cooling, NPI Production Launch Checklist, Kitting Service for Board and Panel Builds.