Contact Us
  • Home
  • COMPONENTS
  • 6-Axis IMU Sensors for Flight Control and Navigation

6-Axis IMU Sensors for Flight Control and Navigation

6-axis inertial measurement units for flight control, stabilisation and navigation boards Triaxial gyroscope and accelerometer in LGA-14 and QFN-24 packages, 1.71 V to 3.6 V supply All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
quote now

Product Specifications

Product Overview

Attitude estimation starts with the gyroscope and the accelerometer pair. The gyro integrates angular rate to give an attitude estimate that drifts slowly, and the accelerometer gives an absolute reference that is noisy in vibration. Everything downstream (the filter, the control loop, the failsafe logic) depends on the noise density, the offset drift and the vibration rejection of the IMU, which is why the sensor choice is made early and rarely changed.

The parts below are the 6-axis IMUs used most often on flight control, gimbal and stabilisation boards. They range from the MPU-6050, which is still requested for repair and for designs that were locked to its register map, to the ICM-42688-P with its low noise density and high output data rate, and the BMI270 with its on chip motion interrupt features. All of them combine a 3-axis gyroscope and a 3-axis accelerometer with 16-bit conversion and a digital interface.

All models are grouped into this single product, so an IMU enquiry can also cover the flash, the magnetometer, the barometer and the passive parts on the same sensor board.

Electrical Specifications

ParameterICM-42688-PBMI270MPU-6050MPU-9250 class (9-axis)
Sensor content3-axis gyroscope and 3-axis accelerometer (6-axis)3-axis gyroscope and 3-axis accelerometer (6-axis)3-axis gyroscope, 3-axis accelerometer, DMP3-axis gyro, 3-axis accel and 3-axis magnetometer
Gyroscope rangeprogrammable, up to plus/minus 2000 dpsplus/minus 125, 250, 500, 1000, 2000 dpsplus/minus 250, 500, 1000, 2000 dpsplus/minus 250 to 2000 dps
Accelerometer rangeprogrammable, up to plus/minus 16 gplus/minus 2, 4, 8, 16 gplus/minus 2, 4, 8, 16 gplus/minus 2 to 16 g
Output data rateup to 32 kHz (low noise mode)25 Hz to 6.4 kHz gyroscope, 0.78 Hz to 1.6 kHz accelerometerup to 1 kHz register rate, 8 kHz gyro sample rateup to 4 kHz
Supply voltage1.71 V to 3.6 VVDD 1.71 V to 3.6 V, VDDIO 1.2 V to 3.6 V2.375 V to 3.46 V (VDD)1.71 V to 3.6 V
InterfaceSPI and I2C, plus I3C on later partsSPI (up to 10 MHz) and I2C, secondary I2C masterI2C up to 400 kHz, SPI on MPU-6000I2C and SPI
Package14-pin LGA, 2.5 mm x 3.0 mm14-pin LGA, 2.5 mm x 3.0 mm x 0.83 mm24-pin QFN, 4 mm x 4 mm x 0.9 mm24-pin QFN, 3 mm x 3 mm
Notable featureLow noise density and wide bandwidth for vibration rejectionOn chip motion interrupts, 2 kB FIFO, 685 uA at full output data rateDigital Motion Processor with MotionFusion and 1024 byte FIFOCompass integrated in the same package

Included Models and Order Codes

Order codes below include the package and the interface option, because the same silicon is often sold in more than one variant and the footprint, not the part family, decides which one your board needs.

ModelAxesInterfacePackageNotes
ICM-42688-P6-axisSPI, I2C, I3C on later parts14-pin LGA, 2.5 x 3.0 mmHigh performance 6-axis IMU, low noise, output data rate to 32 kHz
ICM-42670-P6-axisSPI and I2C14-pin LGA, 2.5 x 3.0 mmLower power 6-axis part in the same footprint family
ICM-426886-axisSPI and I2C14-pin LGAOrdering variants of the ICM-42688 family
ICM-209489-axisSPI and I2C24-pin QFN, 3 x 3 mmGyro, accelerometer and magnetometer with DMP
ICM-206026-axisSPI and I2C16-pin LGA, 3 x 3 mmOlder generation part still specified on existing designs
ICM-206896-axisSPI and I2C14-pin LGAIndustrial oriented variant of the same family
MPU-60506-axisI2C up to 400 kHz24-pin QFN, 4 x 4 mmRegister map compatible with many existing flight stacks, heavily used for repair
MPU-60006-axisSPI and I2C24-pin QFN, 4 x 4 mmSPI version of the MPU-6050
MPU-65006-axisSPI and I2C24-pin QFN, 3 x 3 mmPin compatible upgrade path from earlier MPU parts
MPU-92509-axisSPI and I2C24-pin QFN, 3 x 3 mmIntegrated magnetometer for full attitude reference
BMI2706-axisSPI up to 10 MHz and I2C14-pin LGA, 2.5 x 3.0 x 0.83 mmUltra low power IMU with on chip motion interrupts and 2 kB FIFO
BMI1606-axisSPI and I2C14-pin LGA, 2.5 x 3.0 mmEarlier ultra low power part, still sourced for existing builds
BMI0886-axisSPI and I2C16-pin LGA, 4.5 x 4.5 mmHigh vibration rejection version used in demanding motion control
LSM6DS3TR-C6-axisSPI and I2C14-lead LGA, 2.5 x 3.0 mmST 6-axis part, widely used on low power control boards
LSM6DSV16XTR6-axisSPI and I2C, I3C option14-lead LGA, 2.5 x 3.0 mmRecent ST part for high performance sensor fusion

Key Features

Six Axes In One Package – Gyroscope and accelerometer on the same die pair, which keeps the axes aligned and removes the mechanical mounting error of two separate sensors.

16-Bit Conversion On Both Axes – Resolution and range that cover slow attitude motion and high rate manoeuvres with the same device, by changing the programmable full scale.

Low Noise Density For Vibration – Parts with specified noise density and wide bandwidth so the control filter is not fed by sensor noise in a vibrating airframe.

High Output Data Rates – Up to 32 kHz in low noise mode on the newest parts, which allows averaging in software while still running the control loop fast.

On Chip FIFO And Interrupts – Byte level FIFO and motion triggered interrupts, so the host processor can sleep between frames and still keep an accurate time base.

Digital Interfaces Without Extra Parts – SPI and I2C on the same device, with a secondary I2C master on some parts for a magnetometer or a barometer.

Repair And Legacy Support – Older register maps such as the MPU-6000 and MPU-6050 families remain available for boards that cannot be recompiled, which is the normal case in a repair programme.

Applications

Where these IMU parts are used: Sensor boards are quoted as one item that covers the IMU, the magnetometer, the barometer and the SUPERB PCB and SUPERB PCBA work we support for the same design.

Flight Control And Stabilisation – Attitude and rate sensing on multirotor, fixed wing and VTOL control boards, including redundant two-sensor and three-sensor layouts.

Camera Gimbals And Stabilised Payloads – Axis control on gimbals, stabilised cameras and pointing mechanisms where low noise at low rates matters.

Navigation And Motion Reference Units – Fused with magnetometer, barometer and GNSS data to produce heading, attitude and dead reckoning output.

Industrial Motion And Vibration Monitoring – Machine tilt, shock and vibration measurement where the industrial grade parts and a traceable supply are required.

Sourcing and Cross-Reference

IMU supply is dominated by a small number of package and interface variants, and a board that was designed around one of them cannot always take another part without a layout change. When the exact order code is not available we list the nearest variant in the same family first, including whether it is pin compatible, whether it needs an interrupt configuration change, and whether the register map and the device ID are the same.

For parts that have been discontinued but are still needed for repair, we source verified stock and state the condition and the date code on the quote, because the sensor is the one component in a navigation unit where a remark or a rejected part shows up immediately in the calibration results.

SUPERB Assembly support covers the SMT build of the sensor board where the design goes into volume.

Q: Can you supply discontinued IMU parts such as MPU-6050 for repair and existing designs?

A: Yes. Send the part number and the quantity and the SUPERB Tech sales team will confirm availability, date code and the nearest variant in the same footprint family.

Why Source IMU Sensors from Superb Automation?

  1. Motion Sensor Specialisation: IMUs, magnetometers, barometers and pressure sensors handled as a single group, with the range and interface quoted for the exact order code.
  2. Legacy Part Support: Discontinued gyroscope and accelerometer families sourced from verified stock for repair programmes and for boards that cannot be redesigned.
  3. Package Accuracy: Quotes state the package and the interface option, because footprint and protocol decide whether a substitute can be used at all.
  4. Batch Traceability: Date code, condition and packing stated before the order is placed.
  5. Sensor Board Kitting: IMU, magnetometer, barometer, flash and passives for the same sensor board quoted together to match your BOM.
  6. Engineering Level Reply: Questions about noise, range and interface options are answered against the data sheet, not from a catalogue summary.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Sensors and Detectors, MCU and Embedded Processors, Multi-Function ICs, Components.