STM8S207S6T6
Product Specifications
STM8S207S6T6
ST — MCU & Embedded Processors
Product Overview
The STM8S207S6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S207S6T6: 32 Kbyte Flash STM8S MCU in LQFP44
STM8S207S6T6 is the 32 Kbyte Flash member of the STM8S 8-bit line in a LQFP44 body (10 by 10 mm), with 1024 bytes of true data EEPROM, 6 Kbyte of RAM, 34 general purpose I/O, 9 analog inputs and 15 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.
Order code and memory
| Order code | STM8S207S6T6 |
| Program Flash | 32 Kbytes |
| Data EEPROM | 1024 bytes, 300 kcycle endurance |
| RAM | 6 Kbytes |
| Package | LQFP44, 10 by 10 mm |
| Pin count | 44 |
| Maximum general purpose I/O | 34 |
| External interrupt pins | 31 |
| High sink outputs | 15 |
| ADC channels | 9 of 16 |
| Controller area network | not present |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 24 MHz up to 105 C ambient |
| Flash access | zero wait states to 16 MHz |
| Core | Harvard, 3 stage pipeline, 80 instructions, 20 addressing modes |
| Timers | advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer |
| Analog to digital converter | 10-bit, 9 channels, scan mode, analog watchdog, 14 clock cycles per conversion |
| ADC clock | 1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V |
| Serial interfaces | UART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz |
| Run current | 11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum |
| Low power | halt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off |
| Reset | power-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis |
| Identification | 96-bit unique ID, single wire interface module for debug and programming |
Points to check before this part goes on a BOM
This is the base 44-pin 32 Kbyte part, without the trailing ordering letter that appears on the T6C variant of the same device. Electrically it is the same 34 I/O, 9 channel, 8 CAPCOM, 15 high sink configuration, and the difference between the two lines in a BOM is the ordering suffix rather than the silicon.
For a 32 Kbyte image the 6 Kbytes of RAM is generous, and the 1024 bytes of EEPROM is the part that fills first in a product that logs setpoints or run hours. EEPROM endurance is 300 kcycles, so a once per minute record is a five year budget at one cell, not a ten year one.
Nine analog channels, no reference pins and 8 CAPCOM channels are the resource ceiling here. The 44-pin body is rated 443 mW at 85 C, the same as the 48, 64 and 80-pin bodies, because the limitation is the package footprint rather than the die.
Where this order code fits
Pump, fan and valve controllers, small appliance boards and retrofit modules that need a 10 by 10 mm body with 34 I/O and a real EEPROM. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the resource differences that decide the choice before any code is written.
Questions buyers ask
What is different from the T6C line? The trailing ordering letter. Memory, package, pin count and peripherals are the same, and both are 32 Kbyte parts with 1024 bytes of EEPROM.
How much current at 24 MHz? 11.0 mA typical from Flash at 3.3 V, 18 mA maximum, and 4.0 mA typical when the code runs from RAM.
Can it drive relays directly? There are 15 high sink outputs on this body, which is what they exist for. Inductive loads still need a clamp diode and a check against the total port current in the absolute maximum table.
SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the Vendor Consolidation page walks through the checks that keep a substitute from failing on the bench.