Contact Us

STM8S207MBT6B

Brand: ST
ST STM8S207MBT6B is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S207MBT6B — MCU & Embedded Processors | Superb Automation

STM8S207MBT6B

ST — MCU & Embedded Processors

Product Overview

The STM8S207MBT6B from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S207MBT6B: 128 Kbyte Flash STM8S MCU in LQFP80

STM8S207MBT6B is the 128 Kbyte Flash member of the STM8S 8-bit line in a LQFP80 body (14 by 14 mm), with 2048 bytes of true data EEPROM, 6 Kbyte of RAM, 68 general purpose I/O, 16 analog inputs and 18 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.

Order code and memory

Order codeSTM8S207MBT6B
Program Flash128 Kbytes
Data EEPROM2048 bytes, 300 kcycle endurance
RAM6 Kbytes
PackageLQFP80, 14 by 14 mm
Pin count80
Maximum general purpose I/O68
External interrupt pins37
High sink outputs18
ADC channels16
Controller area networknot present
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock24 MHz up to 105 C ambient
Flash accesszero wait states to 16 MHz
CoreHarvard, 3 stage pipeline, 80 instructions, 20 addressing modes
Timersadvanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer
Analog to digital converter10-bit, 16 channels, scan mode, analog watchdog, 14 clock cycles per conversion
ADC clock1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V
Serial interfacesUART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz
Run current11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum
Low powerhalt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off
Resetpower-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis
Identification96-bit unique ID, single wire interface module for debug and programming

Points to check before this part goes on a BOM

This is the top of the STM8S207 line: 128 Kbytes of Flash, 2048 bytes of data EEPROM and 6 Kbytes of RAM on the 80-pin body. The RAM figure does not move with the Flash figure anywhere in this family, so a firmware image that grows past 64 Kbytes does not gain working memory with it.

The 80-pin package exposes all 16 analog channels, both reference pins, 68 I/O and 18 high sink outputs, with 37 external interrupt inputs. RthJA is 38 C/W and the allowed dissipation is 443 mW at 85 C, which is comfortable for the 11.4 mA typical run current at 24 MHz from 5 V.

With 128 Kbytes of program space the Flash read behaviour at 24 MHz matters: zero wait states are guaranteed only to 16 MHz, and the 24 MHz setting uses one wait state through the WAITSTATE option bit. Time critical loops either run at 16 MHz without wait states or move into RAM, where the run current drops to about 4.4 mA at 5 V.

Where this order code fits

Equipment with a large fixed program image such as a graphical panel, a protocol heavy gateway or a product with several language sets, where 128 Kbytes removes the need for external memory. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the resource differences that decide the choice before any code is written.

Questions buyers ask

Is there a 128 Kbyte part with CAN? Yes, the STM8S208MB on the same 80-pin body. The 207MB has no CAN controller, so the two are pin compatible and function different.

Does more Flash mean more RAM? No. RAM is 6 Kbytes across the whole STM8S207 and STM8S208 line, from 32 to 128 Kbytes of program memory.

What package is it? LQFP80, 14 by 14 mm, 0.5 mm pitch, with 38 C/W junction to ambient.

SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the Supplier Quality Audit page walks through the checks that keep a substitute from failing on the bench.