STM8S207K8T6C
Product Specifications
STM8S207K8T6C
ST — MCU & Embedded Processors
Product Overview
The STM8S207K8T6C from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM8S207K8T6C: 64 Kbyte Flash STM8S MCU in LQFP32
STM8S207K8T6C is the 64 Kbyte Flash member of the STM8S 8-bit line in a LQFP32 body (7 by 7 mm), with 1024 bytes of true data EEPROM, 6 Kbyte of RAM, 25 general purpose I/O, 7 analog inputs and 12 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.
Order code and memory
| Order code | STM8S207K8T6C |
| Program Flash | 64 Kbytes |
| Data EEPROM | 1024 bytes, 300 kcycle endurance |
| RAM | 6 Kbytes |
| Package | LQFP32, 7 by 7 mm |
| Pin count | 32 |
| Maximum general purpose I/O | 25 |
| External interrupt pins | 23 |
| High sink outputs | 12 |
| ADC channels | 7 of 16 |
| Controller area network | not present |
| Temperature grade | suffix 6, minus 40 to plus 85 C |
Electrical and peripheral parameters
| Supply voltage | 2.95 to 5.5 V |
| Maximum CPU clock | 24 MHz up to 105 C ambient |
| Flash access | zero wait states to 16 MHz |
| Core | Harvard, 3 stage pipeline, 80 instructions, 20 addressing modes |
| Timers | advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer |
| Analog to digital converter | 10-bit, 7 channels, scan mode, analog watchdog, 14 clock cycles per conversion |
| ADC clock | 1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V |
| Serial interfaces | UART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz |
| Run current | 11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum |
| Low power | halt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off |
| Reset | power-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis |
| Identification | 96-bit unique ID, single wire interface module for debug and programming |
Points to check before this part goes on a BOM
This is the largest Flash array available in the 32-pin body: 64 Kbytes of program and 1024 bytes of EEPROM, with 25 I/O, 7 analog channels and 12 high sink outputs. Note that the 48-pin 64 Kbyte part carries 1536 bytes of EEPROM, so the smaller package loses 512 bytes of data space as well as pins.
The 32-pin package is rated 360 mW at 85 C against 443 mW for the wider bodies, and it has the fewest high sink outputs in the line. Boards that drive several relays or a multiplexed LED display should add up the sink current before choosing this body.
The USB, CAN and crystal pins are shared with GPIO on this package, so a board that uses an external crystal loses two I/O and a board that uses the 128 kHz low speed internal clock keeps them. The internal 16 MHz RC oscillator is user trimmable and the part starts from it at 2 MHz after reset, which is enough for a safe start before the clock tree is set.
Where this order code fits
Compact sensor and actuator nodes, small drives and cost sensitive modules where 64 Kbytes of program space is needed but board area is fixed at 7 by 7 mm. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page. Both list the resource differences that decide the choice before any code is written.
Questions buyers ask
Can the part run without an external crystal? Yes. The internal 16 MHz RC oscillator is user trimmable and the device starts on it at 2 MHz after reset. An external 1 to 24 MHz crystal is optional and costs two pins.
How many high sink outputs? 12 on the 32-pin body, against 15 on 44 pins and 16 or 18 on the wider packages.
What is the difference from the K6? Only the Flash size, 64 Kbytes against 32 Kbytes. EEPROM, RAM, pin count and peripherals are identical, so the two are interchangeable on an existing board.
SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the BOM Shortage Recovery page walks through the checks that keep a substitute from failing on the bench.