Contact Us

STM8S105C4T6

Brand: ST
ST STM8S105C4T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S105C4T6 — MCU & Embedded Processors | Superb Automation

STM8S105C4T6

ST — MCU & Embedded Processors

Product Overview

The STM8S105C4T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S105C4T6: 16 Kbyte 5 V STM8S access line MCU in LQFP48

STM8S105C4T6 is the 16 Kbyte member of the STM8S105 access line in a LQFP48 body (7 by 7 mm), with 1 Kbyte of true data EEPROM, 2 Kbytes of RAM, 38 general purpose I/O, 35 external interrupt inputs, 9 capture compare channels, 16 high sink outputs and 10 analog inputs. The supply range is 2.95 to 5.5 V, the core runs at up to 16 MHz with zero wait state Flash access, and the converter is 10 bit with its own reference pins.

Order code and memory

Order codeSTM8S105C4T6
Program Flash16 Kbytes
Data EEPROM1 Kbyte, 300 kcycle endurance
RAM2 Kbytes
PackageLQFP48, 7 by 7 mm
Pin count48
Maximum general purpose I/O38
External interrupt pins35
Timer capture compare channels9
ADC channels10 of the 10 channel converter
High sink outputs16
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock16 MHz with zero wait state Flash access
Run current7.7 mA typical at 16 MHz from Flash on 5 V, 3.2 mA with the loop in RAM
Halt current6.5 uA typical at 5 V, 25 uA maximum at 85 C and 80 uA at 125 C
Active haltwait, active halt and halt modes, with the auto wakeup unit
Low power modesperipheral clocks can be switched off one by one
Wake up time7 microseconds from halt
Analog to digital converter10 bit, 10 channels, VREF+ and VREF- pins, 14 clock cycles per conversion
Digital to analog converternot present
Comparatorsnot present on this line
Timersone 16 bit advanced control timer with four capture compare channels and three complementary outputs, two 16 bit general purpose timers with five channels between them, one 8 bit basic timer, auto wakeup timer, window and independent watchdog
Serial interfacesUART with LIN master, SmartCard and IrDA, SPI up to 8 Mbit/s, I2C up to 400 kHz
DMAnot present on this line
Data EEPROM endurance300 kcycle for the 1 Kbyte true data EEPROM
Program memory endurance10 kcycle, 20 years retention at 55 C
Identification96 bit unique ID, single wire interface module, option byte read out protection

Points to check before this part goes on a BOM

The C4 is the 16 Kbyte member of the access line in a 48 pin body, and its selling point is the 5 V supply: 2.95 to 5.5 V means the part runs from the same rail as relays, contactors and industrial sensors without a level translator on every input. The I/O ring is specified as immune to current injection, which matters in a panel where a wire can pick up a spike, and the 16 high sink outputs drive LEDs and small relays directly. RAM is 2 Kbytes, the same as the 32 Kbyte C6 on this line.

The converter is 10 bit with ten channels on this body and its own VREF+ pins, running from 1 to 4 MHz across the full supply range and up to 6 MHz above 4.5 V. A conversion takes 14 clock cycles, so 3.5 microseconds at 4 MHz, and the sample and hold capacitor is 3 pF, which sets the maximum source impedance at the pin. On a 5 V panel the reference is usually the rail, so a noisy rail shows up as gain error rather than offset, and that is worth a separate filter on the sensor supply.

Program memory is 16 Kbytes with 1 Kbyte of true EEPROM beside it and 2 Kbytes of RAM. The Flash is rated 10 kcycles with 20 years retention at 55 C after cycling, while the EEPROM reaches 300 kcycles, so counters and calibration belong in the EEPROM and not in an emulated area. Current is 7.7 mA typical at 16 MHz from Flash on 5 V, dropping to 3.2 mA when the inner loop runs from RAM, and halt is 6.5 uA typical at 5 V.

Where this order code fits

Industrial panel controllers, relay boards, appliance control modules, motor drives with a 5 V sensor supply and any product where the logic has to share a rail with 5 V peripherals. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the Component Lead Time Solutions page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Does this part have CAN? No. The STM8S105 line has no controller area network block; the CAN parts of the same family are the STM8S208 order codes. A CAN node needs a different part number, not a different option byte.

How many ADC channels on 48 pins? Ten, one more than the 44 pin body and three more than the 32 pin body, with VREF+ and VREF- available for an external reference.

What is the maximum clock and supply? 16 MHz at 2.95 to 5.5 V, with zero wait state Flash access at that frequency, so the full 16 MIPS is available at 3.3 V as well as at 5 V.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.