Contact Us

STM8L152R6T6

Brand: ST
ST STM8L152R6T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8L152R6T6 — MCU & Embedded Processors | Superb Automation

STM8L152R6T6

ST — MCU & Embedded Processors

Product Overview

The STM8L152R6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8L152R6T6: 32 Kbyte ultra-low-power STM8L MCU in LQFP64

STM8L152R6T6 is a 32 Kbyte Flash member of the STM8L ultra-low-power line in a LQFP64 body (10 by 10 mm), with 2 Kbytes of RAM, 1 Kbyte of data EEPROM, 54 general purpose I/O, 28 channels on the 12 bit converter and 2 channel of 12 bit DAC. The supply range is 1.65 to 3.6 V without brown out reset, 1.8 to 3.6 V with it and the core runs at up to 16 MHz. It also carries a segment LCD controller driving 8x36 or 4x40 segments with step up converter.

Order code and memory

Order codeSTM8L152R6T6
Program Flash32 Kbytes
Data EEPROM1 Kbyte with ECC and read while write
RAM2 Kbytes
PackageLQFP64, 10 by 10 mm
Pin count64
Maximum general purpose I/O54
ADC channels28 of the 12 bit converter
DAC channels2 of 12 bits with output buffer
LCD controller8x36 or 4x40 segments with step up converter
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage1.65 to 3.6 V without brown out reset, 1.8 to 3.6 V with it
Maximum CPU clock16 MHz, 16 MIPS peak
Run current200 uA per MHz plus 330 uA static
Halt current400 nA typical
Active halt1.4 uA typical with the real time clock running
Low power modes5.9 uA typical in low power run, 3 uA in low power wait
Wake up time4.7 microseconds from halt
Analog to digital converter12 bit, up to 1 Msps, 28 channels, internal reference voltage and temperature sensor on chip
Digital to analog converter2 channel of 12 bits with output buffer, 7 microseconds typical settling into 5 k and 50 pF
Comparators2, one fixed threshold and one rail to rail, both can wake the core
Timersthree 16 bit general purpose timers, one 16 bit advanced control timer with three channels, one 8 bit timer, beeper timer, window and independent watchdog
Serial interfacestwo SPI blocks, one I2C at 400 kHz, three USARTs with ISO 7816 and IrDA
DMA4 channels covering the ADC, both DAC channels, I2C, SPI1, SPI2, USART1 to USART3 and the five timers
Data EEPROM endurance300 kcycle with ECC and read while write
Program memory endurance10 kcycle, 30 years retention at 85 C
Identification96 bit unique ID, single wire interface module, USART bootloader

Points to check before this part goes on a BOM

The R6 keeps the 64 pin body and the large display controller but halves the memory against the R8: 32 Kbytes of Flash, 2 Kbytes of RAM and 1 Kbyte of EEPROM. It is the part for a big glass on a small firmware, a heating controller or a timer with a fixed menu, where the pin count is driven by the display and the serial links rather than by code size. Choosing it over the R8 is purely a memory decision because everything else in the package is identical.

The peripheral count is the reason to accept 2 Kbytes of RAM. Three USARTs, two SPI blocks, one I2C, two 12 bit DAC channels, 28 converter channels and 54 I/O in a 10 by 10 mm body give a product room to grow without a board change, and the display controller takes 8 by 36 or 4 by 40 segments which covers most appliance and HVAC glasses. The RAM ceiling is real though: a display buffer plus a protocol queue plus metrology history will not fit, so the firmware has to stream rather than buffer.

Current figures on this density are 200 uA per MHz plus 330 uA static in run mode, 5.9 uA in low power run, 1.4 uA in active halt with the clock running and 400 nA in halt, with the 4.7 microsecond wake up shared across the line. Because the display stays alive in active halt, a product that refreshes the glass continuously sits at the 1.4 uA figure rather than the 400 nA one, and that difference decides the battery life of a wall unit.

Where this order code fits

Heating and ventilation controllers, appliance panels with a fixed menu, timers and counters with a large glass, and retrofit boards that must reuse an existing 64 pin footprint. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What is the difference between the R6 and the R8? The program array, the RAM and the EEPROM: 32 against 64 Kbytes, 2 against 4 Kbytes and 1 against 2 Kbytes. Package, pinout and the peripheral set are the same.

How much current does the display add in sleep? Active halt with the real time clock and the display running is 1.4 uA typical on this density against 400 nA in plain halt, so the glass is the dominant load in a sleeping product.

Are all 28 ADC channels bonded on 64 pins? Yes, the 64 pin body carries the full 28 channel converter, one more than the 48 pin body and ten more than the 32 pin body of the same family.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.