Contact Us

STM32L152CBT6

Brand: ST
ST STM32L152CBT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32L152CBT6 — MCU & Embedded Processors | Superb Automation

STM32L152CBT6

ST — MCU & Embedded Processors

Product Overview

The STM32L152CBT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32L152CBT6: 128 Kbyte, LQFP48 body

STM32L152CBT6 is a member of the STM32L151x6/8/B and STM32L152x6/8/B low power line described by DocID17659 Rev 12. The order code fixes 128 Kbytes of Flash, 16 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 14 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down supply.

Order code and memory

Order codeSTM32L152CBT6
Program Flash128 Kbytes
SRAM16 Kbytes
Data EEPROM4 Kbytes with ECC
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels14 channels on the 12 bit converter
Digital to analog converter2 channels of 12 bits
Segment LCD driver4x18 segments
Supply voltage1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down
Maximum CPU clock32 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient
DatasheetDocID17659 Rev 12

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 32 MHz, 1.25 DMIPS per MHz, memory protection unit
Clock sources1 to 24 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC trimmed to plus or minus 1 percent, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC, and a PLL that also produces the 48 MHz USB clock
Low power modes214 microamps per MHz in Run mode, 9 microamps in Low power run, 1.2 microamps in Stop with the RTC, 0.9 microamps in Standby with the RTC and 10 nanoamps of I/O leakage, with wakeup from Stop under 8 microseconds
Timersten timers: six 16 bit timers with up to four compare channels each, two 16 bit basic timers and the independent and window watchdogs, plus the SysTick counter and the RTC
Serial interfacestwo SPI blocks at 16 Mbit/s, two I2C blocks with SMBus and PMBus, three USARTs with ISO 7816 and IrDA support and one USB 2.0 device port clocked from the internal PLL
Analogone 12 bit ADC at 1 Msps, two 12 bit DAC channels with output buffers and two ultra low power comparators that double as a wakeup source, with capacitance sensing on up to 20 channels
Memory interfacenot present on this body
Flash and EEPROM enduranceprogram memory rated 10 kcycles minimum over minus 40 to plus 105 C with 300 kcycles typical, EEPROM 30 kcycles minimum with 300 typical, and 30 years of retention at 85 C against 10 years at 105 C
Thermal resistance junction to ambient55 C/W on LQFP48
Input tolerance5 V tolerant on 73 of the 83 I/O of the 100 pin body, all mappable on 16 external interrupt vectors
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC and the backup registers alive with the main rail off
Statusfull production per the datasheet cover

Points to check before this part goes on a BOM

The order code is C for 48 pins, B for 128 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. It is the largest memory available in the 48 pin body with the glass driver, and the next code up in that body, CBU6, is a 151 part with no driver at all.

The driver covers 4x18 segments, which is 72 segments on four backplanes. That is a three and a half digit display with annunciators, and it is the reason this part exists: the same memory in the 64 pin body gives 128 segments but takes 36 pins instead of 22.

22 of the 37 I/O go to the glass in a full 4x18 application, which leaves 15 pins for the sensor inputs, the serial port and the debug interface. A board that uses the display and needs twelve analog channels has to look at the 64 pin body, because the pins and not the memory become the limit first.

The LQFP48 is rated 55 C/W junction to ambient, which is 364 mW at an 85 C ambient against a 105 C junction. That is a smaller budget than the 64 pin body offers and it is the number to check when a display backlight driver or a relay coil shares the same copper area.

The 4 Kbytes of EEPROM hold meter totals and calibration constants independently of the program flash, and the 16 Kbytes of SRAM hold the segment map and the measurement queue. On a 48 pin part the memory is rarely the constraint, which is why projects stay on this code for years after the first prototype.

1.2 microamps in Stop with the RTC is 10.5 mAh over a year, so a meter that updates its display once a minute and sleeps in between can run from a lithium cell for its service life. The display itself draws more than the part during the update, and that is the number to measure on the bench.

The USB port is present on this part and takes its 48 MHz clock from the PLL, which means a crystal on the high speed oscillator for any link that has to enumerate over temperature. Boards that only use the UART for configuration can leave the crystal off and run from the internal 16 MHz RC.

The 48 pin codes in this document differ in memory and in the display driver and not in pinout, so a substitution has to compare the memory column first. CBT6 against C8T6 is 128 Kbytes against 64, and against CBU6 it is the driver and the package that change, not the pin count.

Where this order code fits

It is the small display part of the line, used where a 3.5 digit readout and a handful of sensor inputs have to fit a 48 pin footprint. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the BOM Shortage Recovery page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Is 72 segments enough for a three and a half digit display? Yes. Four backplanes at 18 segment lines cover three and a half digits with decimal points, unit annunciators and a battery symbol, which is the usual content of a handheld meter glass.

Can I use all 14 analog channels with the display on? Not with a full 4x18 glass. The display consumes 22 pins and the analog channels sit on the same ports, so a display board normally gives up four to six channels.

What is the thermal budget on this package? 55 C/W junction to ambient, which is 364 mW with an 85 C ambient and a 105 C junction. The figure assumes the exposed pins are soldered to copper on a board with normal airflow, not to a bare pad.

Which code is the 256 Kbyte version in this body? STM32L151CCU6 is the 256 Kbyte part in the UFQFPN48 body and it has no display driver. There is no 256 Kbyte LQFP48 code with the driver in this document.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.