STM32L151VDT6
Product Specifications
STM32L151VDT6
ST — MCU & Embedded Processors
Product Overview
The STM32L151VDT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32L151VDT6: 384 Kbyte, LQFP100 body
STM32L151VDT6 is a member of the STM32L151xD and STM32L152xD low power line described by DS8576 Rev 13. The order code fixes 384 Kbytes of Flash, 48 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 83 general purpose I/O and 25 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down supply.
Order code and memory
| Order code | STM32L151VDT6 |
| Program Flash | 384 Kbytes |
| SRAM | 48 Kbytes |
| Data EEPROM | 12 Kbytes with ECC |
| Package | LQFP100, 14 x 14 mm, 100 pins |
| Maximum general purpose I/O | 83 |
| Analog input channels | 25 channels on the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| Segment LCD driver | not present on this part |
| Supply voltage | 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down |
| Maximum CPU clock | 32 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient |
| Datasheet | DS8576 Rev 13 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 32 MHz, 1.25 DMIPS per MHz, memory protection unit |
| Clock sources | 1 to 24 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC trimmed to plus or minus 1 percent, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC, and a PLL that also produces the 48 MHz USB clock |
| Low power modes | 230 microamps per MHz in Run mode with both flash banks active, 11 microamps in Low power run and 4.4 microamps in Stop with the RTC running |
| Timers | eleven timers: one 32 bit timer, six 16 bit timers with up to four compare channels, two 16 bit basic timers and two watchdog timers |
| Serial interfaces | eight SPI blocks of which two are I2S, two I2C blocks, five USARTs, one USB 2.0 device port and one SDIO interface |
| Analog | one 12 bit ADC at 1 Msps, two 12 bit DAC channels, three operational amplifiers and two ultra low power comparators, with capacitance sensing on up to 33 channels |
| Memory interface | not present on this body |
| Flash and EEPROM endurance | program memory rated 10 kcycles at 105 C with 300 kcycles typical, EEPROM 30 kcycles minimum, and retention of 30 years at 85 C against 10 years at 105 C |
| Thermal resistance junction to ambient | 43 C/W on LQFP100 |
| Input tolerance | 5 V tolerant inputs on the general purpose ports, all mappable on 16 external interrupt vectors |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC and the backup registers alive with the main rail off |
| Status | full production per the datasheet cover |
Points to check before this part goes on a BOM
The order code is V for 100 pins, D for 384 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. The 151 prefix means no segment driver, so a board that wants the glass in this body has to take STM32L152VDT6, which is otherwise the same part.
83 general purpose I/O with 48 Kbytes of SRAM and 12 Kbytes of EEPROM is the combination that makes a protocol gateway fit one chip: several serial ports, a memory interface for a buffer SRAM and enough RAM to hold a frame queue without an external part.
The memory interface here is the multiplexed version: address and data share pins, and the bank covers a multiplexed NOR or PSRAM. On a 100 pin board that saves 16 pins against a non multiplexed interface, which is the difference between fitting the connectors and not.
The LQFP100 is rated 43 C/W junction to ambient, so 581 mW at an 85 C ambient against a 110 C junction. On a gateway with an Ethernet PHY and a switching regulator nearby, the copper under the part is what decides whether the figure is met.
230 microamps per MHz in Run mode with both flash banks active, 11 microamps in Low power run and 4.4 microamps with the RTC running. The double bank is why the Run mode figure is higher than the single bank part at the same clock, and it is a price paid for read while write.
Five USARTs and one SDIO interface appear in this document and not in the 64 pin body. A concentrator that talks to four meters over UART and logs to an SD card uses both, and that combination is the practical reason this part exists in the range.
Three operational amplifiers and 25 analog channels sit behind a 1 Msps 12 bit converter. A gateway that also samples supply rails and enclosure temperature uses four or five of those channels, and the rest stay available for a sensor board added later.
The 151 prefix has no display driver and the 152 twin does. In second source work that difference is invisible on the package drawing and on most of the pin table, so a drop in check has to read the prefix and not only the memory and the package.
Where this order code fits
It is the 384 Kbyte part in the 100 pin body without the display driver, common on data concentrators and industrial gateways that need pins and memory but no glass. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Is this the same part as STM32L152VDT6? Functionally yes, apart from the segment display driver. The 152 code adds 4x44 or 8x40 segments and the step-up converter for the glass, and the rest of the memory and peripherals match.
How many serial ports does it have? Five USARTs, eight SPI blocks of which two are I2S, two I2C blocks and one SDIO interface, plus one USB 2.0 device port. That set is what makes four meter inputs and a card slot fit one chip.
What kind of external memory can it drive? A multiplexed NOR or PSRAM on bank 1 through the memory interface. The interface on this body does not offer separate address and data lines or the NAND option.
How does the EEPROM size compare with the smaller densities? 12 Kbytes here against 8 Kbytes in the xC document and 4 Kbytes in the x6/8/B document. It is the largest in the line and it is separate from the two flash banks.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.