STM32L151RDT6
Product Specifications
STM32L151RDT6
ST — MCU & Embedded Processors
Product Overview
The STM32L151RDT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32L151RDT6: 384 Kbyte, LQFP64 body
STM32L151RDT6 is a member of the STM32L151xD and STM32L152xD low power line described by DS8576 Rev 13. The order code fixes 384 Kbytes of Flash, 48 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 21 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down supply.
Order code and memory
| Order code | STM32L151RDT6 |
| Program Flash | 384 Kbytes |
| SRAM | 48 Kbytes |
| Data EEPROM | 12 Kbytes with ECC |
| Package | LQFP64, 10 x 10 mm, 64 pins |
| Maximum general purpose I/O | 51 |
| Analog input channels | 21 channels on the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| Segment LCD driver | not present on this part |
| Supply voltage | 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down |
| Maximum CPU clock | 32 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient |
| Datasheet | DS8576 Rev 13 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 32 MHz, 1.25 DMIPS per MHz, memory protection unit |
| Clock sources | 1 to 24 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC trimmed to plus or minus 1 percent, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC, and a PLL that also produces the 48 MHz USB clock |
| Low power modes | 230 microamps per MHz in Run mode with both flash banks active, 11 microamps in Low power run and 4.4 microamps in Stop with the RTC running |
| Timers | eleven timers: one 32 bit timer, six 16 bit timers with up to four compare channels, two 16 bit basic timers and two watchdog timers |
| Serial interfaces | eight SPI blocks of which two are I2S, two I2C blocks, five USARTs, one USB 2.0 device port and one SDIO interface |
| Analog | one 12 bit ADC at 1 Msps, two 12 bit DAC channels, three operational amplifiers and two ultra low power comparators, with capacitance sensing on up to 33 channels |
| Memory interface | not present on this body |
| Flash and EEPROM endurance | program memory rated 10 kcycles at 105 C with 300 kcycles typical, EEPROM 30 kcycles minimum, and retention of 30 years at 85 C against 10 years at 105 C |
| Thermal resistance junction to ambient | 46 C/W on LQFP64 |
| Input tolerance | 5 V tolerant inputs on the general purpose ports, all mappable on 16 external interrupt vectors |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC and the backup registers alive with the main rail off |
| Status | full production per the datasheet cover |
Points to check before this part goes on a BOM
The order code is R for 64 pins, D for 384 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. This document covers D only, so the C and E densities come from two other documents and a substitution has to start by checking which one the part belongs to.
48 Kbytes of SRAM against 16 on the previous density is the reason this part exists. A logger that buffers a page of records, a checksum table and a serial stack runs out of RAM long before it runs out of flash, and 16 Kbytes is where that usually happens.
The flash is organised in two banks with read while write, so a firmware image can be received into one bank while the other keeps running. That is the capability that separates this document from the single bank xC part, and it is worth checking in firmware notes rather than assumed from the density.
The memory interface on this body is multiplexed only: the address and data lines share pins, and the interface reaches bank 1 for a multiplexed NOR or PSRAM part. The full interface with separate address and data and the NAND option belongs to the 132 and 144 pin bodies in the same document.
The LQFP64 is rated 46 C/W junction to ambient, which is 543 mW at an 85 C ambient and a 110 C junction. The two flash banks add a little to the run current and nothing to the static budget, so the thermal answer is the same as the smaller densities in this body.
230 microamps per MHz in Run mode is a figure with both banks active, which is the worst case and not the normal one. 11 microamps in Low power run and 4.4 microamps with the RTC running are the numbers that matter for a logger that spends most of its life asleep.
21 analog channels on the 1 Msps 12 bit converter, with three operational amplifiers on this document against two on the xC part. A bridge plus a two stage filter fits inside the part, which is often why a board moves to this density rather than adding analog parts to the BOM.
12 Kbytes of EEPROM is the largest in the low power line and covers a device identity block, calibration and a rolling log without external memory. At four bytes per record that is 3072 records per full cycle and about 92 million writes at the 30 kcycle minimum.
Where this order code fits
It is the 384 Kbyte member in the 64 pin body, used where a data logger needs 48 Kbytes of RAM to buffer records and the board has to stay in a 10 mm package. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Does the part support read while write on the flash? Yes, the flash is two banks and the document describes read while write between them. A bootloader that swaps images relies on it, and the firmware has to place the routine in the bank that is not being written.
How much RAM is left after the stack and buffers? 48 Kbytes in total, of which the stack, the heap and the peripheral buffers take what they take. A logger that holds 32 Kbytes of record buffer still has room, which is the step that 16 Kbyte parts cannot make.
Can it drive external memory? Only a multiplexed bank 1 interface for NOR or PSRAM on this body. A part with separate address and data lines and NAND support is the 132 or 144 pin body in the same document.
What is the pin compatible alternative if it is short? STM32L151RCT6 is the 256 Kbyte version in the xC document, same 64 pin LQFP. It carries 32 Kbytes of SRAM instead of 48 and a single flash bank, so the memory interface and the read while write behaviour do not carry over.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.