Contact Us

STM32L151C8T6

Brand: ST
ST STM32L151C8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32L151C8T6 — MCU & Embedded Processors | Superb Automation

STM32L151C8T6

ST — MCU & Embedded Processors

Product Overview

The STM32L151C8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32L151C8T6: 64 Kbyte, LQFP48 body

STM32L151C8T6 is a member of the STM32L151x6/8/B and STM32L152x6/8/B low power line described by DocID17659 Rev 12. The order code fixes 64 Kbytes of Flash, 10 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 14 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down supply.

Order code and memory

Order codeSTM32L151C8T6
Program Flash64 Kbytes
SRAM10 Kbytes
Data EEPROM4 Kbytes with ECC
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels14 channels on the 12 bit converter
Digital to analog converternot present
Segment LCD drivernot present on this part
Supply voltage1.65 to 3.6 V with the brownout reset enabled, 1.8 to 3.6 V without it and down to 1.65 V in power down
Maximum CPU clock32 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient
DatasheetDocID17659 Rev 12

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 32 MHz, 1.25 DMIPS per MHz, memory protection unit
Clock sources1 to 24 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC trimmed to plus or minus 1 percent, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC, and a PLL that also produces the 48 MHz USB clock
Low power modes214 microamps per MHz in Run mode, 9 microamps in Low power run, 1.2 microamps in Stop with the RTC, 0.9 microamps in Standby with the RTC and 10 nanoamps of I/O leakage, with wakeup from Stop under 8 microseconds
Timersten timers: six 16 bit timers with up to four compare channels each, two 16 bit basic timers and the independent and window watchdogs, plus the SysTick counter and the RTC
Serial interfacestwo SPI blocks at 16 Mbit/s, two I2C blocks with SMBus and PMBus, three USARTs with ISO 7816 and IrDA support and one USB 2.0 device port clocked from the internal PLL
Analogone 12 bit ADC at 1 Msps, two 12 bit DAC channels with output buffers and two ultra low power comparators that double as a wakeup source, with capacitance sensing on up to 20 channels
Memory interfacenot present on this body
Flash and EEPROM enduranceprogram memory rated 10 kcycles minimum over minus 40 to plus 105 C with 300 kcycles typical, EEPROM 30 kcycles minimum with 300 typical, and 30 years of retention at 85 C against 10 years at 105 C
Thermal resistance junction to ambient55 C/W on LQFP48
Input tolerance5 V tolerant on 73 of the 83 I/O of the 100 pin body, all mappable on 16 external interrupt vectors
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC and the backup registers alive with the main rail off
Statusfull production per the datasheet cover

Points to check before this part goes on a BOM

The order code reads as C for 48 pins, 8 for 64 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. Nothing in the string states the 10 Kbytes of SRAM or the 4 Kbytes of EEPROM, so two codes that differ only in the flash letter look alike on a purchase order and behave differently in firmware that sizes buffers against the top of RAM.

The 4 Kbytes of EEPROM are separate from program flash and carry ECC. At four bytes per record that is 1024 records, and against the 30 kcycle minimum in the endurance table the part supports about 30.7 million record writes, which is why meter totals and calibration constants belong in the EEPROM and not in an emulated flash page.

There is no segment driver on this part. The LCD belongs to the STM32L152 codes in the same document, so a board that needs a glass display has to move to STM32L152C8T6, the same 48 pin LQFP with 4x18 segments, or carry an external driver and lose the reason for the 48 pin body in the first place.

1.2 microamps in Stop with the RTC is 10.5 mAh across a year, and 0.9 microamps in Standby is 7.9 mAh, so on a 225 mAh coin cell the self discharge of the cell is the larger term. The 214 microamps per MHz in the feature list is a Run mode figure at 1.8 V and comes to 6.85 mA at the full 32 MHz.

The LQFP48 is rated 55 C/W junction to ambient. Against a 105 C junction limit and an 85 C ambient that is 364 mW of total dissipation, and the core at 32 MHz accounts for roughly 12 mW of it, so the budget belongs to the I/O and to whatever regulator shares the board. Eight indicator LEDs at 8 mA spend more than the core does.

Fourteen analog channels come out of port A, port B and port C, and those same pins carry the USB pair, the crystal and the debug port. A board that enumerates on USB and keeps serial wire debug has fewer than fourteen channels free, so the channel count on the pinout is a maximum and not a promise.

The document separates 1.65 to 3.6 V with the brownout reset enabled from 1.8 to 3.6 V without it. On a 3.3 V rail the difference does not matter, but on a two cell alkaline pack that sags towards 2.0 V the choice decides whether the part resets cleanly or drifts into the low voltage corner of its own specification.

The pin compatible codes in this body are C6 with 32 Kbytes of Flash and 10 Kbytes of SRAM, and CB with 128 Kbytes and 16 Kbytes. A firmware image built for the CB code will not fit the 64 Kbyte part even though the footprint and the pinout match, so a second source check has to compare the memory column and not the package drawing.

Where this order code fits

It is the 64 Kbyte, 48 pin member of the line and turns up on meter front ends, small sensor nodes and interface boards that need the EEPROM more than they need pins. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Does STM32L151C8T6 drive an LCD directly? No. The segment driver sits on the STM32L152 codes only. STM32L152C8T6 is the same 48 pin body with 4x18 segments, so the board can keep its footprint and gain the glass driver.

How long does the 4 Kbyte EEPROM last? The endurance table gives 30 kcycles minimum per cell with 300 typical. At four bytes per record that is 1024 records per full cycle and roughly 30.7 million writes at the minimum figure, with ECC covering single bit upsets.

Can it run straight from two AA cells? The supply range is 1.65 to 3.6 V with the brownout reset enabled, which covers two alkaline cells from 3.0 V fresh down to 2.0 V near end of life. Any 3.3 V peripheral on the same board still needs a regulator stage.

Is there a 105 C ambient option? This document states one range for the line, minus 40 to plus 85 C ambient with a 105 C junction. A 105 C ambient belongs to the STM32L151xD document, where ordering suffix 7 carries it.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.