Contact Us

STM32L071RBT6

Brand: ST
ST STM32L071RBT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32L071RBT6 — MCU & Embedded Processors | Superb Automation

STM32L071RBT6

ST — MCU & Embedded Processors

Product Overview

The STM32L071RBT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32L071RBT6: 128 Kbyte, LQFP64 body

STM32L071RBT6 is a member of the STM32L071xx access line low power family described by DS10690 Rev 7. The order code fixes 128 Kbytes of Flash, 20 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 analog channels, and the core runs at up to 32 MHz from a 1.65 to 3.6 V with the brownout reset enabled and 1.8 to 3.6 V without it supply.

Order code and memory

Order codeSTM32L071RBT6
Program Flash128 Kbytes
SRAM20 Kbytes
Data EEPROM6 Kbytes with ECC
PackageLQFP64, 10 x 10 mm, 64 pins
Maximum general purpose I/O51
Analog input channels16 channels on the 12 bit converter
Digital to analog converternot present
Segment LCD drivernot present on this part
Supply voltage1.65 to 3.6 V with the brownout reset enabled and 1.8 to 3.6 V without it
Maximum CPU clock32 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient
DatasheetDS10690 Rev 7

Peripheral and electrical parameters

CoreARM Cortex-M0+ at up to 32 MHz, 0.95 DMIPS per MHz, memory protection unit
Clock sources1 to 25 MHz crystal oscillator, 32 kHz oscillator for the RTC with calibration, 16 MHz factory trimmed internal RC, internal 37 kHz low power RC, internal multispeed 65 kHz to 4.2 MHz RC and a PLL for the core clock
Low power modes93 microamps per MHz in Run mode, 0.86 microamps in Stop with the RTC and 20 Kbytes of RAM retained, 0.29 microamps in Standby on three wakeup pins and 41 microamps for a 12 bit conversion at 10 ksps
Timerseleven timers: two 16 bit timers with four channels, two 16 bit timers with two channels, one low power 16 bit timer, two 16 bit basic timers, the RTC, SysTick and the two watchdogs
Serial interfacesup to six SPI blocks of which one is I2S, three I2C blocks of which two carry SMBus and PMBus, four USARTs of which two carry ISO 7816 and IrDA, one UART and one LPUART that wakes from Stop
Analogone 12 bit ADC at 1.14 Msps and two ultra low power comparators; this line carries no DAC
Memory interfacenot present on this body
Flash and EEPROM enduranceflash and EEPROM cycling are listed separately, with retention stated at 85 C and at 105 C after 10 kcycles
Thermal resistance junction to ambient46 C/W on LQFP64
Input tolerance5 V tolerant on up to 51 I/O of the 64 pin body, all mappable on 16 external interrupt vectors
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC and the backup registers alive with the main rail off
Statusfull production per the datasheet cover

Points to check before this part goes on a BOM

The order code is R for 64 pins, B for 128 Kbytes of Flash, T for the LQFP body and 6 for the industrial range. The 071 prefix carries 6 Kbytes of EEPROM at this density and no USB port and no display driver, which are the two features that separate it from the 072 and 073 codes.

0.86 microamps in Stop with the RTC and the full 20 Kbytes of RAM retained is the headline of this part, and 0.29 microamps in Standby on three wakeup pins is below it. Over a year those are 7.5 and 2.5 mAh, so a 1200 mAh cell is limited by self discharge rather than by the microcontroller.

20 Kbytes of SRAM with 6 Kbytes of EEPROM at 128 Kbytes of flash is a memory mix built for logging. A node that holds a week of readings in RAM and a calibration record in EEPROM needs the RAM far more than it needs flash, which is why this density outsells the 192 Kbyte code in metering.

The ADC is 1.14 Msps at 12 bits and takes 41 microamps for a conversion at 10 ksps, which is a figure that includes the converter only. A board that leaves the converter clocked between readings spends more than the part does in Stop, so the sequence matters more than the resolution.

The LQFP64 is rated 46 C/W junction to ambient, so 435 mW at an 85 C ambient against a 105 C junction. 93 microamps per MHz in Run mode is the lowest of the low power lines here and comes to 2.98 mA at the full 32 MHz from an 1.8 V rail.

The LPUART wakes the part from Stop on a byte, which is how a node listens to a bus without waking the core for every edge. Four USARTs of which two carry ISO 7816 and IrDA plus three I2C blocks with SMBus cover meter and sensor buses without an external bridge.

There is no USB port on this code and no segment driver. A product that needs either has to move to the STM32L072 or STM32L073 codes, which share the pinout in most bodies, so the migration is a part change and a firmware rebuild rather than a board revision.

The 3 Kbyte EEPROM figure in the same document belongs to the 64 Kbyte codes and 6 Kbytes to the 128 and 192 Kbyte codes, so a substitution between densities changes the EEPROM map and not only the flash size. That is the field most often missed when a part is swapped under pressure.

Where this order code fits

It is the 128 Kbyte member of the low power access line, used on battery sensors, water and gas meters and remote nodes where Stop mode current decides the product life. Boards weighing it against a neighbouring density or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Does this part have USB? No. The USB port belongs to the STM32L072 and STM32L073 codes in the same family. A board that needs USB has to change prefix, and the pinout compatibility depends on the body.

What is the Stop mode current with the RTC running? 0.86 microamps with the full 20 Kbytes of RAM retained, which is 7.5 mAh over a year. Standby on three wakeup pins is 0.29 microamps, or 2.5 mAh over the same period.

Is there a display driver? Not on this code. The segment driver belongs to the STM32L073. A metering product that shows a glass display picks a code from that branch instead.

How much EEPROM comes with 128 Kbytes? 6 Kbytes, against 3 Kbytes on the 64 Kbyte codes in the same document. The EEPROM map changes with the density, so a firmware image moved between them needs its address table checked.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.