STM32F215RET6
Product Specifications
STM32F215RET6
ST — MCU & Embedded Processors
Product Overview
The STM32F215RET6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F215RET6: 512 Kbyte, LQFP64 body
STM32F215RET6 is a member of the STM32F215 and STM32F217 performance line with cryptographic acceleration described by DocID17050 Rev 13. The order code fixes 512 Kbytes of Flash, 128 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 external channels on each of the 12 bit converters, and the core runs at up to 120 MHz from a 1.8 to 3.6 V supply.
Order code and memory
| Order code | STM32F215RET6 |
| Program Flash | 512 Kbytes |
| SRAM | 128 Kbytes |
| Package | LQFP64, 10 x 10 mm, 64 pins |
| Maximum general purpose I/O | 51 |
| Analog input channels | 16 external channels per converter |
| Digital to analog converter | not present |
| External memory controller | not available on this 64 pin body, the controller needs pins the package does not bond |
| Supply voltage | 1.8 to 3.6 V |
| Maximum CPU clock | 120 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
| Datasheet | DocID17050 Rev 13 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 120 MHz with the adaptive real time accelerator, 1.25 DMIPS per MHz, 150 DMIPS, a memory protection unit and single cycle multiply and divide |
| Clock sources | 4 to 26 MHz high speed external crystal, 16 MHz factory trimmed internal RC, 32.768 kHz low speed internal and external sources, a main PLL and a separate audio PLL for the I2S blocks |
| Timers | two advanced-control 16 bit timers with complementary outputs and dead time, four full featured general purpose timers of which TIM2 and TIM5 are 32 bit, six further general purpose 16 bit timers, two basic timers, the independent and window watchdogs, the SysTick counter and the RTC, which is the seventeen the cover counts |
| Serial interfaces | three SPI blocks two of which mux to I2S, three I2C blocks, four USARTs and two UARTs, two CAN 2.0B active controllers and one SDIO interface |
| DMA | two DMA controllers with eight streams each and a FIFO per stream, sixteen streams in total, with circular buffer support |
| ADC | three 12 bit successive approximation converters with a 0.5 microsecond conversion time, each sharing up to 16 external channels, up to 24 channels across the three on the larger bodies and up to 6 Msps in triple interleaved mode |
| DAC | two 12 bit channels with output buffers |
| Ethernet | not present, Ethernet is an STM32F217 feature |
| Camera interface | not present on the STM32F215 |
| Cryptographic acceleration | AES 128, 192 and 256 bit, Triple DES and a HASH unit for MD5 and SHA-1, plus an analog true random number generator |
| Programmable voltage detector | programmable voltage detector with selectable thresholds, plus power on reset, power down reset and brownout reset |
| Debug port | serial wire debug and JTAG, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC, the 4 Kbytes of backup SRAM and the backup registers alive with the main rail off |
| Flash endurance and retention | 10 kcycles at minus 40 to plus 85 C and 1 kcycle at 105 C, with 30 years of retention at 85 C after one kcycle, 20 years at 55 C after 10 kcycles and 10 years at 105 C |
| Thermal resistance junction to ambient | 45 C/W on this package |
| Input tolerance | almost all inputs 5 V tolerant, with fast I/O toggling to 60 MHz on the larger bodies |
| USB | one OTG full speed port on the device pins and one OTG high speed port that needs an external ULPI PHY |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
Fifty one general purpose pins carrying a 120 MHz core, 128 Kbytes of SRAM and a hardware AES block is a lot of function in a 10 x 10 mm package. The board level consequence is that the pins are heavily shared: the USB full speed pair, the two CAN channels, the second USART and the cryptographic block's own bus all draw on the same ports, so the pin assignment has to be worked out function by function rather than assumed.
The high speed OTG port cannot be used on this body. It needs twelve ULPI pins for an external PHY and the 64 pin package does not bond them, so the full speed port with its two pins is the only USB path here. That is enough for a device or a host at 12 Mbit/s and it is the reason this part appears on serial encrypted links rather than on high throughput interfaces.
The SRAM is the full 112 Kbytes of SRAM1 plus 16 Kbytes of SRAM2 even at 512 Kbytes of Flash, which is unusual for a small package. For an encrypted data path that matters: an AES block processing 1 Kbyte chunks needs a source and a destination buffer, and a receive queue behind it, and 128 Kbytes holds that with room for the application.
There is no external memory controller on 64 pins. Boards that need one take the 100 pin or 144 pin body, where the reduced or full flexible static memory controller is bonded. What the 64 pin part offers instead is a self contained node that keeps everything in internal memory, which for a sensor or a secure endpoint is the right shape anyway.
The LQFP64 is rated 45 C/W, so at 85 C ambient the dissipation budget is about 440 mW. With the crypto block active the current rises measurably above an idle benchmark, and a node that encrypts a continuous stream should be checked at that load. The 105 C ambient version of the same part is available for sealed enclosures.
Where this order code fits
It is the smallest package in the STM32F21x range, 512 Kbytes with the cryptographic block in a 10 x 10 mm LQFP64, for secure tokens, encrypted serial links and small controllers that need AES in hardware. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Can AES run from the hardware block on this package? Yes. The cryptographic block is part of the STM32F215 device and is not package dependent. The block handles AES with 128, 192 and 256 bit keys, Triple DES and MD5 or SHA-1 hashing, with the random number generator supplying seed material.
Why is USB limited to full speed here? The high speed OTG port needs twelve ULPI pins for an external PHY, and this 64 pin body does not bond them. The full speed port on PA11 and PA12 is the usable USB path on this package.
Does the STM32F215 have Ethernet? No. Ethernet and the camera interface are STM32F217 features only. A networked board moves to the F217 codes, which are available in the 100, 144 and 176 pin bodies.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.